Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,12 +20,10 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27		-
28		-
29	29	= 3. Support End Node and firmware version =
30	30
31	31	(% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
...	...	@@ -99,7 +99,6 @@
99	99	)))
100	100	)))
101	101
102		-
103	103	= 4. System Management Commands =
104	104
105	105	== 4.1 Change Uplink Interval ==
...	...	@@ -173,8 +173,6 @@
173	173
174	174	(((
175	175	If the downlink payload=**04FF**, the end node will reboot.
176		-
177		-
178	178	)))
179	179
180	180	== 4.3 Reset to factory Default ==
...	...	@@ -351,7 +351,6 @@
351	351	OK
352	352	)))
353	353
354		-
355	355	== 5.4 Device Address ==
356	356
357	357	Feature: Get or Set the Device Address.
...	...	@@ -370,7 +370,6 @@
370	370	)))
371	371	|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
372	372
373		-
374	374	== 5.5 Device EUI ==
375	375
376	376	Feature: Get or Set the Device EUI.
...	...	@@ -389,7 +389,6 @@
389	389	OK
390	390	)))
391	391
392		-
393	393	== 5.6 Network ID ==
394	394
395	395	Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
...	...	@@ -406,7 +406,6 @@
406	406	)))
407	407	|(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
408	408
409		-
410	410	== 5.7 Network Session Key ==
411	411
412	412	Feature: Get or Set the Network Session Key
...	...	@@ -423,7 +423,6 @@
423	423	)))
424	424	|(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
425	425
426		-
427	427	= 6. Joining and sending date on LoRaWAN network =
428	428
429	429	== 6.1 Confirm Mode ==
...	...	@@ -801,7 +801,7 @@
801	801
802	802	)))
803	803
804		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
805	805
806	806	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
807	807
...	...	@@ -1006,8 +1006,6 @@
1006	1006
1007	1007	(((
1008	1008	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1009		-
1010		-
1011	1011	)))
1012	1012
1013	1013	== 7.21 Get or Set RXwindows2 timeout ==