Changes for page End Device AT Commands and Downlink Command

Last modified by kai on 2024/09/06 10:00

From version < 21.1 >

edited by Xiaoling
on 2022/05/27 17:53

To version < 38.72 >

edited by Xiaoling
on 2022/05/31 09:18

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -3,6 +3,7 @@
  {{toc/}}
++
  = 1. Introduction =
  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
@@ -19,11 +19,10 @@
  * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
  * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
--** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
--** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
++** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
++** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
  ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
--
  = 3. Support End Node and firmware version =
  (% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
@@ -98,7 +98,6 @@
  )))
--
  = 4. System Management Commands =
  == 4.1 Change Uplink Interval ==
@@ -335,7 +335,6 @@
  )))
  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
--
  == 5.3 Application Session Key ==
  Feature: Get or Set the Application Session Key.
@@ -354,8 +354,6 @@
  OK
  )))
--
--
  == 5.4 Device Address ==
  Feature: Get or Set the Device Address.
@@ -374,8 +374,6 @@
  )))
  |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
--
--
  == 5.5 Device EUI ==
  Feature: Get or Set the Device EUI.
@@ -394,8 +394,6 @@
  OK
  )))
--
--
  == 5.6 Network ID ==
  Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
@@ -412,8 +412,6 @@
  )))
  |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
--
--
  == 5.7 Network Session Key ==
  Feature: Get or Set the Network Session Key
@@ -430,8 +430,6 @@
  )))
  |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
--
--
  = 6. Joining and sending date on LoRaWAN network =
  == 6.1 Confirm Mode ==
@@ -497,7 +497,6 @@
  )))
--
  == 6.4 LoRa® Network Join Mode ==
  Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
@@ -527,7 +527,6 @@
  * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
--
  == 6.5 LoRa® Network Join Status ==
  Feature: LoRa® Network Join Status.
@@ -544,7 +544,6 @@
  )))
--
  == 6.6 Print Last Received Data in Raw Format ==
  Feature: Print Last Received Data in Raw Format<port:data>.
@@ -561,7 +561,6 @@
  )))
--
  == 6.7 Print Last Received Data in Binary Format ==
  Feature: Print Last Received Data in Binary Format<port:data>.
@@ -578,7 +578,6 @@
  )))
--
  == 6.8 Send Text Data ==
  Feature: Send Text Data<port:data>.
@@ -599,7 +599,6 @@
  )))
--
  == 6.9 Send Hexadecimal Data ==
  Feature: Send hexadecimal data along with the application port.
@@ -619,7 +619,6 @@
  )))
--
  = 7. LoRaWAN network management =
  == 7.1 Adaptive Data Rate ==
@@ -652,7 +652,6 @@
  * **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
--
  == 7.2 LoRa® Class ==
  Feature: Get or Set the Device Class(Currently only support class A, class C).
@@ -672,7 +672,6 @@
  )))
--
  == 7.3 Duty Cycle Setting ==
  Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
@@ -692,7 +692,6 @@
  )))
--
  == 7.4 Data Rate ==
  Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
@@ -722,7 +722,6 @@
  * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
--
  == 7.5 Frame Counter Downlink ==
  Feature: Get or Set the Frame Counter Downlink.
@@ -744,7 +744,6 @@
  )))
--
  == 7.6 Frame Counter Uplink ==
  Feature: Get or Set the Frame Counter Uplink.
@@ -764,7 +764,6 @@
  )))
--
  == 7.7 Join Accept Delay1 ==
  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
@@ -784,7 +784,6 @@
  )))
--
  == 7.8 Join Accept Delay2 ==
  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
@@ -804,7 +804,6 @@
  )))
--
  == 7.9 Public Network Mode ==
  Feature: Get or Set the public network mode. (0: off, 1: on)
@@ -826,7 +826,6 @@
  )))
--
  == 7.10 Receive Delay1 ==
  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
@@ -846,7 +846,6 @@
  )))
--
  == 7.11 Receive Delay2 ==
  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
@@ -866,7 +866,6 @@
  )))
--
  == 7.12 Rx2 Window Data Rate ==
  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
@@ -886,7 +886,6 @@
  )))
--
  == 7.13 Rx2 Window Frequency ==
  Feature: Get or Set the Rx2 window frequency
@@ -906,7 +906,6 @@
  )))
--
  == 7.14 Transmit Power ==
  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
@@ -933,7 +933,6 @@
  * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
--
  == 7.15 RSSI of the Last Received Packet ==
  Feature: Get or Set the Rx2 window frequency
@@ -950,7 +950,6 @@
  )))
--
  == 7.16 SNR of the Last Received Packet ==
  Feature: Get the SNR of the last received packet
@@ -967,7 +967,6 @@
  )))
--
  == 7.17 Application Port ==
  Feature: Get or set the application port.
@@ -996,7 +996,6 @@
  * **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
--
  == 7.18 Single Channel Mode ==
  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
@@ -1014,7 +1014,6 @@
  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
--
  == 7.19 Eight Channel Mode ==
  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
@@ -1045,7 +1045,6 @@
  * **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
--
  == 7.20 Get or Set RXwindows1 timeout ==
  Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
@@ -1091,7 +1091,6 @@
  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
--
  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
  Feature: Get or Set uplinkdwelltime
@@ -1120,7 +1120,6 @@
  * **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
--
  == 7.23 Set Packet Receiving Response Level ==
  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
@@ -1163,7 +1163,6 @@
  * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
--
  = 8. AT Commands Combination =
  == 8.1 Set a fix RX2DR for downlink window ==
@@ -1172,7 +1172,6 @@
  * **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
--
  == 8.2 Use Downlink Command to set a fix uplink DR ==
  {{info}}

Changes for page End Device AT Commands and Downlink Command

Summary

Details

Applications

Navigation