Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,6 +3,7 @@
3	3	{{toc/}}
4	4
5	5
	6	+
6	6	= 1. Introduction =
7	7
8	8	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -19,9 +19,9 @@
19	19
20	20	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
21	21	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
22		-** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
23		-** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
24		-** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
	23	+** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
	24	+** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
	25	+** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
25	25
26	26	= 3. Support End Node and firmware version =
27	27
...	...	@@ -169,6 +169,8 @@
169	169
170	170	(((
171	171	If the downlink payload=**04FF**, the end node will reboot.
	173	+
	174	+
172	172	)))
173	173
174	174	== 4.3 Reset to factory Default ==
...	...	@@ -293,6 +293,7 @@
293	293	OK
294	294	)))
295	295
	299	+
296	296	= 5. Keys, IDs and EUIs management =
297	297
298	298	== 5.1 Application EUI ==
...	...	@@ -311,6 +311,7 @@
311	311	)))
312	312	|(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
313	313
	318	+
314	314	== 5.2 Application Key ==
315	315
316	316	Feature: Get or Set the Application Key.
...	...	@@ -327,6 +327,7 @@
327	327	)))
328	328	|(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
329	329
	335	+
330	330	== 5.3 Application Session Key ==
331	331
332	332	Feature: Get or Set the Application Session Key.
...	...	@@ -345,6 +345,8 @@
345	345	OK
346	346	)))
347	347
	354	+
	355	+
348	348	== 5.4 Device Address ==
349	349
350	350	Feature: Get or Set the Device Address.
...	...	@@ -790,7 +790,7 @@
790	790
791	791	)))
792	792
793		-== 7.11Receive Delay2 ==
	801	+== 7.11 Receive Delay2 ==
794	794
795	795	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
796	796
...	...	@@ -995,6 +995,8 @@
995	995
996	996	(((
997	997	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
	1006	+
	1007	+
998	998	)))
999	999
1000	1000	== 7.21 Get or Set RXwindows2 timeout ==