Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,6 +3,7 @@
3	3	{{toc/}}
4	4
5	5
	6	+
6	6	= 1. Introduction =
7	7
8	8	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -19,10 +19,12 @@
19	19
20	20	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
21	21	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
22		-** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
23		-** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
24		-** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
	23	+** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
	24	+** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
	25	+** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
25	25
	27	+
	28	+
26	26	= 3. Support End Node and firmware version =
27	27
28	28	(% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
...	...	@@ -96,6 +96,7 @@
96	96	)))
97	97	)))
98	98
	102	+
99	99	= 4. System Management Commands =
100	100
101	101	== 4.1 Change Uplink Interval ==
...	...	@@ -169,6 +169,8 @@
169	169
170	170	(((
171	171	If the downlink payload=**04FF**, the end node will reboot.
	176	+
	177	+
172	172	)))
173	173
174	174	== 4.3 Reset to factory Default ==
...	...	@@ -345,6 +345,7 @@
345	345	OK
346	346	)))
347	347
	354	+
348	348	== 5.4 Device Address ==
349	349
350	350	Feature: Get or Set the Device Address.
...	...	@@ -363,6 +363,7 @@
363	363	)))
364	364	|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
365	365
	373	+
366	366	== 5.5 Device EUI ==
367	367
368	368	Feature: Get or Set the Device EUI.
...	...	@@ -381,6 +381,7 @@
381	381	OK
382	382	)))
383	383
	392	+
384	384	== 5.6 Network ID ==
385	385
386	386	Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
...	...	@@ -397,6 +397,7 @@
397	397	)))
398	398	|(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
399	399
	409	+
400	400	== 5.7 Network Session Key ==
401	401
402	402	Feature: Get or Set the Network Session Key
...	...	@@ -413,6 +413,7 @@
413	413	)))
414	414	|(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
415	415
	426	+
416	416	= 6. Joining and sending date on LoRaWAN network =
417	417
418	418	== 6.1 Confirm Mode ==
...	...	@@ -790,7 +790,7 @@
790	790
791	791	)))
792	792
793		-== 7.11Receive Delay2 ==
	804	+== 7.11 Receive Delay2 ==
794	794
795	795	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
796	796
...	...	@@ -995,6 +995,8 @@
995	995
996	996	(((
997	997	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
	1009	+
	1010	+
998	998	)))
999	999
1000	1000	== 7.21 Get or Set RXwindows2 timeout ==
...	...	@@ -1088,7 +1088,6 @@
1088	1088	* **AT+ADR=0 **~-~-> Disable ADR first
1089	1089	* **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1090	1090
1091		-
1092	1092	== 8.2 Use Downlink Command to set a fix uplink DR ==
1093	1093
1094	1094	{{info}}
...	...	@@ -1097,6 +1097,6 @@
1097	1097
1098	1098	Same as:
1099	1099
1100		-* AT+ADR=0 [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1101		-* AT+DR=5 [[Reference>>||anchor="H7.4DataRate"]]
1102		-* AT+TXP=0 [[Reference>>||anchor="H7.14TransmitPower"]]
	1112	+* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
	1113	+* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
	1114	+* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]