Changes for page End Device AT Commands and Downlink Command
Last modified by kai on 2024/09/06 10:00
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -123,13 +123,9 @@ 123 123 **Downlink Command: 0x01** 124 124 {{/info}} 125 125 126 -((( 127 127 Format: Command Code (0x01) followed by 3 bytes time value. 128 -))) 129 129 130 -((( 131 131 If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01. 132 -))) 133 133 134 134 * **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds 135 135 * **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds ... ... @@ -163,13 +163,9 @@ 163 163 **Downlink Command: 0x04** 164 164 {{/info}} 165 165 166 -((( 167 167 Format: Command Code (0x04) followed by FF. 168 -))) 169 169 170 -((( 171 171 If the downlink payload=**04FF**, the end node will reboot. 172 -))) 173 173 174 174 == 4.3 Reset to factory Default == 175 175 ... ... @@ -200,13 +200,9 @@ 200 200 **Downlink Command: 0x04** 201 201 {{/info}} 202 202 203 -((( 204 204 Format: Command Code (0x04) followed by FE. 205 -))) 206 206 207 -((( 208 208 If the downlink payload=**04FE**, Reset Parameters to Factory Default, Keys Reserve. 209 -))) 210 210 211 211 212 212 == 4.4 Show Firmware Version == ... ... @@ -230,25 +230,17 @@ 230 230 **Downlink Command: 0x26 (Valid in 006 stack)** 231 231 {{/info}} 232 232 233 -((( 234 234 Downlink Format: 0x26 235 -))) 236 236 237 -((( 238 238 Device will reply with firmware version info, device info. frequency band info. detail please check device user manual. Total 5 bytes Example: If device is of firmware version 1.1.0 Upload: xx ~-~- yy ~-~- zz ~-~- 110 total 5 bytes 239 -))) 240 240 241 -((( 242 242 **xx: Software Type:** 243 -))) 244 244 245 245 * 0x00 01: LGT92 Version 246 246 * 0x00 02: LBT1 247 247 * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01 248 248 249 -((( 250 250 **yy: Frequency Band:** 251 -))) 252 252 253 253 * 0x01: EU868 254 254 * 0x02: US915 ... ... @@ -261,9 +261,7 @@ 261 261 * 0x09: AS923-2 262 262 * 0xa0: AS923-3 263 263 264 -((( 265 265 **zz: Subband** 266 -))) 267 267 268 268 firmware version: v1.1.0 ~-~-> 110 269 269 ... ... @@ -987,15 +987,11 @@ 987 987 ))) 988 988 |(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK 989 989 990 -((( 991 -**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph. 992 -))) 968 +AT+RX1TWO is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph. 993 993 994 994 [[image:image-20220511120050-1.png]] 995 995 996 -((( 997 997 Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink. 998 -))) 999 999 1000 1000 == 7.21 Get or Set RXwindows2 timeout == 1001 1001 ... ... @@ -1096,6 +1096,6 @@ 1096 1096 1097 1097 Same as: 1098 1098 1099 -* AT+ADR=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/# H7.1AdaptiveDataRate]]1100 -* AT+DR=5 [[Reference>>http:// 8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.4DataRate]]1101 -* AT+TXP=0 [[Reference>>http:// 8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.14TransmitPower]]1073 +* AT+ADR=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#Adaptive_Data_Rate]] 1074 +* AT+DR=5 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Data_Rate]] 1075 +* AT+TXP=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Transmit_Power]]