Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -1,32 +1,864 @@
1		-{{box cssClass="floatinginfobox" title="**Contents**"}}
	1	+Contens
	2	+
2	2	{{toc/}}
3		-{{/box}}
4	4
5		-= Paragraph 1 =
6	6
7		-Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
	6	+= 1. Introduction =
8	8
9		-== Sub-paragraph ==
	8	+Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
10	10
11		-Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
	10	+* **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
	11	+* **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
12	12
13		-== Sub-paragraph ==
	13	+**This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
	14	+
14	14
15		-Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
	16	+= 2. How to use AT Commands or Downlink command =
16	16
17		-=== Sub-sub paragraph ===
	18	+* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
	19	+* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
	20	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	21	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	22	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
18	18
19		-Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
	24	+= 3. Support End Node and firmware version =
20	20
	26	+(% border="1" style="background-color:#ffffcc; color:green; width:942.222px" %)
	27	+|=(% colspan="3" style="width: 939px;" %) Dragino STM32 base hardware Firmware / LoRaWAN stack list
	28	+|(% style="width:187px" %)**Model**|(% style="width:306px" %)**Description**|(% style="width:443px" %)**Firmware Version <~-~-> Stack Version**
	29	+|(% style="width:187px" %)[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],|(% style="width:306px" %)Open Source Generic LoRaWAN Sensor Node|(% style="width:443px" %)LSN50 v1.6.0 <~-~-> DR-LWS-003;(((
	30	+LSN50 v1.7.0 <~-~-> DR-LWS-005; ~-~-> Support since this version
	31	+)))
	32	+|(% style="width:187px" %)[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],|(% style="width:306px" %)LoRaWAN GPS Tracker|(% style="width:443px" %)LGT92 v1.6.3 <~-~-> DR-LWS-003;(((
	33	+LGT92 v1.6.4 <~-~-> DR-LWS-005;~-~-> Support since this version
	34	+)))
	35	+|(% style="width:187px" %)[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],|(% style="width:306px" %)LoRaWAN BLE Indoor Tracker|(% style="width:443px" %)LBT1 v1.0 <~-~-> DR-LWS-005;
	36	+|(% style="width:187px" %)[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],|(% style="width:306px" %)LoRaWAN RS485 Modbus Converter|(% style="width:443px" %)RS485-LN v1.3 <~-~-> DR-LWS-005;
	37	+|(% style="width:187px" %)[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],|(% style="width:306px" %)LoRaWAN Temperature & Humidity Sensor|(% style="width:443px" %)LHT65 v1.7 <~-~-> DR-LWS-003;(((
	38	+LHT65 v1.8.0 <~-~-> DR-LWS-005;~-~-> Support since this version
	39	+)))
21	21
22		-= Paragraph 2 =
	41	+= 4. System Management Commands =
23	23
24		-Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
	43	+== 4.1 Change Uplink Interval ==
25	25
26		-== Sub-paragraph ==
	45	+Feature: Change LoRaWAN End Node Transmit Interval.
27	27
28		-Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
	47	+(% class="box infomessage" %)
	48	+(((
	49	+AT Command: AT+TDC
	50	+)))
29	29
30		-== Sub-paragraph ==
	52	+(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
	53	+|=(% colspan="3" style="width: 724px;" %) AT+TDC
	54	+|(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
	55	+|(% style="width:165px" %)AT+TDC=?|(% style="width:227px" %)Show current transmit Interval|(% style="width:329px" %)30000(((
	56	+OK
31	31
32		-Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
	58	+the interval is 30000ms = 30s
	59	+)))
	60	+|(% style="width:165px" %)AT+TDC=60000|(% style="width:227px" %)Set Transmit Interval|(% style="width:329px" %)OK(((
	61	+Set transmit interval to 60000ms = 60 seconds
	62	+)))
	63	+
	64	+**Downlink Command: 0x01**
	65	+
	66	+Format: Command Code (0x01) followed by 3 bytes time value.
	67	+
	68	+If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
	69	+
	70	+* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
	71	+* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
	72	+
	73	+== 4.2 Reboot End Node ==
	74	+
	75	+Feature: Reboot End Node to perform a new OTAA or ABP Join.
	76	+
	77	+{{info}}
	78	+AT Command: ATZ
	79	+{{/info}}
	80	+
	81	+(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
	82	+|=(% colspan="3" %)ATZ: Trig a reset of the MCU
	83	+|**Command Example**|**Function**|**Response**
	84	+)))
	85	+|ATZ|Reset MCU|
	86	+(((
	87	+Device reset and show booting info
	88	+
	89	+LSN50 Device/LoRa ST Module
	90	+
	91	+Image Version: XX
	92	+
	93	+Frequency Band: XX
	94	+
	95	+DevEui= XX XX XX XX XX XX XX XX
	96	+
	97	+<followed by the Tx and Rx information>
	98	+)))
	99	+
	100	+Downlink Command: 0x04
	101	+
	102	+Format: Command Code (0x04) followed by FF.
	103	+
	104	+If the downlink payload=04FF, the end node will reboot.
	105	+
	106	+== 4.3 Reset to factory Default ==
	107	+
	108	+Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
	109	+
	110	+AT Command: AT+FDR
	111	+
	112	+|=(% colspan="3" %)Reset to factory default
	113	+|**Command Example**|**Function**|**Response**
	114	+|AT+FDR|Reset to factory default|Device reset to factory default parameters and show booting info
	115	+
	116	+{{{LSN50 Device/LoRa ST Module
	117	+Image Version: XX
	118	+Frequency Band: XX
	119	+DevEui= XX XX XX XX XX XX XX XX
	120	+Please set the parameters or reset Device to apply change
	121	+}}}
	122	+
	123	+
	124	+Downlink Command: 0x04
	125	+
	126	+Format: Command Code (0x04) followed by FE.
	127	+
	128	+If the downlink payload=04FE, Reset Parameters to Factory Default, Keys Reserve.
	129	+
	130	+
	131	+== 4.4 Show Firmware Version ==
	132	+
	133	+Feature: Show firmware version. No downlink command yet.
	134	+
	135	+AT Command: AT+VER
	136	+
	137	+|=(% colspan="3" %)AT+VER: Image Version and Frequency Band
	138	+|**Command Example**|**Function**|**Response**
	139	+|AT+VER=?|Show Image version and Frequency Band|
	140	+
	141	+{{{1.3 EU868
	142	+OK
	143	+}}}
	144	+
	145	+
	146	+Downlink Command: 0x26 (Valid in 006 stack)
	147	+
	148	+Downlink Format: 0x26
	149	+
	150	+Device will reply with firmware version info, device info. frequency band info. detail please check device user manual. Total 5 bytes Example: If device is of firmware version 1.1.0 Upload: xx ~-~- yy ~-~- zz ~-~- 110 total 5 bytes
	151	+
	152	+xx: Software Type:
	153	+
	154	+* 0x00 01: LGT92 Version
	155	+* 0x00 02: LBT1
	156	+* 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
	157	+
	158	+yy: Frequency Band:
	159	+
	160	+* 0x01: EU868
	161	+* 0x02: US915
	162	+* 0x03: IN865
	163	+* 0x04: AU915
	164	+* 0x05: KZ865
	165	+* 0x06: RU864
	166	+* 0x07: AS923
	167	+* 0x08: AS923-1
	168	+* 0x09: AS923-2
	169	+* 0xa0: AS923-3
	170	+
	171	+zz: Subband
	172	+
	173	+firmware version: v1.1.0 ~-~-> 110
	174	+
	175	+
	176	+== 4.5 Show System Configure ==
	177	+
	178	+Feature: Show All configure. No downlink command yet.
	179	+
	180	+AT Command: AT+CFG
	181	+
	182	+|=(% colspan="3" %)AT+CFG: Print all configurations
	183	+|**Command Example**|**Function**|**Response**
	184	+|AT+CFG|Show all configures|
	185	+
	186	+{{{AT+DEUI = XX XX XX XX XX XX XX XX
	187	+AT+DADDR=XXXXXXXX
	188	+……….
	189	+AT+RX2WTO=X
	190	+AT+CHS=868100000
	191	+OK
	192	+}}}
	193	+
	194	+
	195	+= 5. Keys, IDs and EUIs management =
	196	+
	197	+== 5.1 Application EUI ==
	198	+
	199	+Feature: Get or Set the Application EUI.
	200	+
	201	+AT Command: AT+APPEUI
	202	+
	203	+|=(% colspan="3" %)AT+APPEUI
	204	+|**Command Example**|**Function**|**Response**
	205	+|AT+APPEUI=?|Get the Application EUI|00 b3 d5 00 00 00 00 00(((
	206	+OK
	207	+)))
	208	+|AT+APPEUI=00 b3 d5 7e f0 00 4d 34|Set the Application EUI|OK
	209	+
	210	+== 5.2 Application Key ==
	211	+
	212	+Feature: Get or Set the Application Key.
	213	+
	214	+AT Command: AT+APPKEY
	215	+
	216	+|=(% colspan="3" %)AT+APPKEY
	217	+|**Command Example**|**Function**|**Response**
	218	+|AT+APPKEY=?|Get the Application Key|00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35(((
	219	+OK
	220	+)))
	221	+|AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|Set the Application Key.|OK
	222	+
	223	+== 5.3 Application Session Key ==
	224	+
	225	+Feature: Get or Set the Application Session Key.
	226	+
	227	+AT Command: AT+APPSKEY
	228	+
	229	+|=(% colspan="3" %)AT+APPSKEY
	230	+|**Command Example**|**Function**|**Response**
	231	+|AT+APPSKEY=?|Get the Application Session Key|00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2(((
	232	+OK
	233	+)))
	234	+|AT+APPSKEY=00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2|Set the Application Session Key.|(While Error in format, return AT_PARAM_ERROR)(((
	235	+OK
	236	+)))
	237	+
	238	+== 5.4 Device Address ==
	239	+
	240	+Feature: Get or Set the Device Address.
	241	+
	242	+AT Command: AT+DADDR
	243	+
	244	+|=(% colspan="3" %)AT+DADDR
	245	+|**Command Example**|**Function**|**Response**
	246	+|AT+DADDR=?|Get the Application Session Key.|(While Error in format, return AT_PARAM_ERROR)(((
	247	+A8 40 41 FF
	248	+
	249	+OK
	250	+)))
	251	+|AT+DADDR=A8 40 41 FF|Set the Application Session Key.|OK
	252	+
	253	+== 5.5 Device EUI ==
	254	+
	255	+Feature: Get or Set the Device EUI.
	256	+
	257	+AT Command: AT+DEUI
	258	+
	259	+|=(% colspan="3" %)AT+DEUI
	260	+|**Command Example**|**Function**|**Response**
	261	+|AT+DEUI=?|Get the Device EUI.|00 44 34 22 33 45 55 55(((
	262	+OK
	263	+)))
	264	+|AT+DEUI=A8 40 41 FF FF 12 34 56|Set the Device EUI.|(System will write new value to Device EUI,While Error in format, return AT_PARAM_ERROR)(((
	265	+OK
	266	+)))
	267	+
	268	+== 5.6 Network ID ==
	269	+
	270	+Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
	271	+
	272	+AT Command: AT+NWKID
	273	+
	274	+|=(% colspan="3" %)AT+NWKID
	275	+|**Command Example**|**Function**|**Response**
	276	+|AT+NWKID=?|Get the Network ID.|a8 40 41 ff(((
	277	+OK
	278	+)))
	279	+|AT+NWKID=A8 40 41 FF|Set the Network ID.|OK
	280	+
	281	+== 5.7 Network Session Key ==
	282	+
	283	+Feature: Get or Set the Network Session Key
	284	+
	285	+AT Command: AT+NWKSKEY
	286	+
	287	+|=(% colspan="3" %)AT+NWKSKEY
	288	+|**Command Example**|**Function**|**Response**
	289	+|AT+NWKSKEY=?|Get the Network Session Key.|00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92(((
	290	+OK
	291	+)))
	292	+|AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|Set the Network Session Key.|OK
	293	+
	294	+= 6. Joining and sending date on LoRaWAN network =
	295	+
	296	+== 6.1 Confirm Mode ==
	297	+
	298	+Feature: Get or Set the confirmation mode (0-1).
	299	+
	300	+AT Command: AT+CFM
	301	+
	302	+|=(% colspan="3" %)AT+CFM
	303	+|**Command Example**|**Function**|**Response**
	304	+|AT+CFM=?|Get the confirmation mode|0(((
	305	+OK
	306	+)))
	307	+|AT+CFM=1|Set the confirmation mode|OK
	308	+|AT+CFM=2|Set the confirmation mode|While Error in format, return AT_PARAM_ERROR
	309	+
	310	+Downlink Command: 0x05
	311	+
	312	+Format: Command Code (0x05) followed by 2 bytes mode value.
	313	+
	314	+If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
	315	+
	316	+* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
	317	+* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
	318	+
	319	+== 6.2 Confirm Status ==
	320	+
	321	+Feature: Get confirmation status of the last AT+SEND (0-1).
	322	+
	323	+AT Command: AT+CFS
	324	+
	325	+|=(% colspan="3" %)AT+CFS
	326	+|**Command Example**|**Function**|**Response**
	327	+|AT+CFS=?|Get confirmation status|0(((
	328	+OK
	329	+)))
	330	+
	331	+== 6.3 Join LoRa® Network ==
	332	+
	333	+Feature: Join network.
	334	+
	335	+AT Command: AT+JOIN
	336	+
	337	+|=(% colspan="3" %)AT+JOIN
	338	+|**Command Example**|**Function**|**Response**
	339	+|AT+JOIN ?|Get imformation.|AT+JOIN: Join network(((
	340	+OK
	341	+
	342	+While Error in format, return AT_BUSY_ERROR
	343	+)))
	344	+
	345	+== 6.4 LoRa® Network Join Mode ==
	346	+
	347	+Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
	348	+
	349	+AT Command: AT+NJM
	350	+
	351	+|=(% colspan="3" %)AT+NJM
	352	+|**Command Example**|**Function**|**Response**
	353	+|AT+NJM=?|Get the Network Join Mode|1(((
	354	+OK
	355	+)))
	356	+|AT+NJM=0|Set the Network Join Mode|OK
	357	+|AT+NJM=2|Set the Network Join Mode|While Error in format, return AT_PARAM_ERROR
	358	+
	359	+Downlink Command: 0x20
	360	+
	361	+Format: Command Code (0x20) followed by 1 bytes mode value.
	362	+
	363	+If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
	364	+
	365	+* Example 1: Downlink Payload: 2000 ~/~/ Set AT+NJM=O
	366	+* Example 2: Downlink Payload: 2001 ~/~/ Set AT+NJM=1
	367	+
	368	+== 6.5 LoRa® Network Join Status ==
	369	+
	370	+Feature: LoRa® Network Join Status.
	371	+
	372	+AT Command: AT+NJS
	373	+
	374	+|=(% colspan="3" %)AT+NJS
	375	+|**Command Example**|**Function**|**Response**
	376	+|AT+NJS=?|Get the join status.|0(((
	377	+OK
	378	+)))
	379	+
	380	+== 6.6 Print Last Received Data in Raw Format ==
	381	+
	382	+Feature: Print Last Received Data in Raw Format<port:data>.
	383	+
	384	+AT Command: AT+RECV
	385	+
	386	+|=(% colspan="3" %)AT+RECV
	387	+|**Command Example**|**Function**|**Response**
	388	+|AT+RECV=?|print last received data in raw format.|0:(((
	389	+OK
	390	+)))
	391	+
	392	+== 6.7 Print Last Received Data in Binary Format ==
	393	+
	394	+Feature: Print Last Received Data in Binary Format<port:data>.
	395	+
	396	+AT Command: AT+RECVB
	397	+
	398	+|=(% colspan="3" %)AT+RECVB
	399	+|**Command Example**|**Function**|**Response**
	400	+|AT+RECVB=?|print last received data in binary format (with hexadecimal values).|2: 0010(((
	401	+OK
	402	+)))
	403	+
	404	+== 6.8 Send Text Data ==
	405	+
	406	+Feature: Send Text Data<port:data>.
	407	+
	408	+AT Command: AT+SEND
	409	+
	410	+|=(% colspan="3" %)AT+SEND
	411	+|**Command Example**|**Function**|**Response**
	412	+|AT+SEND=12:hello world|Send text data along with the application port.|OK(((
	413	+While Error in format, return
	414	+
	415	+AT_BUSY_ERROR/AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
	416	+
	417	+
	418	+)))
	419	+
	420	+== 6.9 Send Hexadecimal Data ==
	421	+
	422	+Feature: Send hexadecimal data along with the application port.
	423	+
	424	+AT Command: AT+SENDB
	425	+
	426	+|=(% colspan="3" %)AT+SENDB
	427	+|**Command Example**|**Function**|**Response**
	428	+|AT+SENDB=12:abcdef0123456789|Send hexadecimal data along with the application port.|OK
	429	+|AT+SENDB=abcdef0123456789|Send hexadecimal data along with the application port.|While Error in format, return(((
	430	+AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
	431	+
	432	+
	433	+)))
	434	+
	435	+= 7. LoRaWAN network management =
	436	+
	437	+== 7.1 Adaptive Data Rate ==
	438	+
	439	+Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on).
	440	+
	441	+
	442	+AT Command: AT+ADR
	443	+
	444	+|=(% colspan="3" %)AT+ADR
	445	+|**Command Example**|**Function**|**Response**
	446	+|AT+ADR=?|Get the Adaptive Data Rate setting.|1(((
	447	+OK
	448	+)))
	449	+|AT+ADR=0|Set the Adaptive Data Rate setting.|OK
	450	+|AT+ADR=2|Set the Adaptive Data Rate setting.|While Error in format, return(((
	451	+AT_PARAM_ERROR
	452	+)))
	453	+
	454	+Downlink Command: 0x22
	455	+
	456	+
	457	+If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
	458	+
	459	+* Example 1: Downlink Payload: 2201 ~/~/ Set AT+ADR=1.
	460	+* Example 2: Downlink Payload: 2200FFFF ~/~/ Set AT+ADR=0.
	461	+
	462	+== 7.2 LoRa® Class ==
	463	+
	464	+Feature: Get or Set the Device Class(Currently only support class A, class C).
	465	+
	466	+AT Command:AT+CLASS
	467	+
	468	+|=(% colspan="3" %)AT+CLASS
	469	+|**Command Example**|**Function**|**Response**
	470	+|AT+CLASS=?|Get the Device Class.|A(((
	471	+OK
	472	+)))
	473	+|AT+CLASS=C|Set the Device Class.|OK(((
	474	+
	475	+)))
	476	+
	477	+== 7.3 Duty Cycle Setting ==
	478	+
	479	+Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
	480	+
	481	+AT Command:AT+DCS
	482	+
	483	+|=(% colspan="3" %)AT+DCS
	484	+|**Command Example**|**Function**|**Response**
	485	+|AT+DCS=?|Get the ETSI Duty Cycle setting.|1(((
	486	+OK
	487	+)))
	488	+|AT+DCS=1|Set the ETSI Duty Cycle setting.|OK(((
	489	+
	490	+)))
	491	+
	492	+== 7.4 Data Rate ==
	493	+
	494	+Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
	495	+
	496	+AT Command: AT+DR
	497	+
	498	+|=(% colspan="3" %)AT+DR
	499	+|**Command Example**|**Function**|**Response**
	500	+|AT+DR=?|Get the Data Rate.|5(((
	501	+OK
	502	+)))
	503	+|AT+DR=2|Set the Data Rate.|OK(((
	504	+
	505	+)))
	506	+
	507	+Downlink Command: 0x2200aaFF
	508	+
	509	+
	510	+If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
	511	+
	512	+* Example 1: Downlink Payload: 220001FF ~/~/ Set AT+DR=1.
	513	+* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+DR=0.
	514	+
	515	+== 7.5 Frame Counter Downlink ==
	516	+
	517	+Feature: Get or Set the Frame Counter Downlink.
	518	+
	519	+AT Command:AT+FCD
	520	+
	521	+|=(% colspan="3" %)AT+FCD
	522	+|**Command Example**|**Function**|**Response**
	523	+|AT+FCD=?|Get the Frame Counter Downlink.|0(((
	524	+OK
	525	+)))
	526	+|AT+FCD=10|Set the Frame Counter Downlink.|(System will write new value to FCD)(((
	527	+OK
	528	+
	529	+
	530	+)))
	531	+
	532	+== 7.6 Frame Counter Uplink ==
	533	+
	534	+Feature: Get or Set the Frame Counter Uplink.
	535	+
	536	+AT Command:AT+FCU
	537	+
	538	+|=(% colspan="3" %)AT+FCU
	539	+|**Command Example**|**Function**|**Response**
	540	+|AT+FCU=?|Get the Frame Counter Uplink.|0(((
	541	+OK
	542	+)))
	543	+|AT+FCU=10|Set the Frame Counter Uplink.|OK(((
	544	+
	545	+)))
	546	+
	547	+== 7.7 Join Accept Delay1 ==
	548	+
	549	+Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
	550	+
	551	+AT Command:AT+JN1DL
	552	+
	553	+|=(% colspan="3" %)AT+JN1DL
	554	+|**Command Example**|**Function**|**Response**
	555	+|AT+JN1DL=?|Get the Join Accept Delay.|5000(((
	556	+OK
	557	+)))
	558	+|AT+JN1DL=10000|Set the Join Accept Delay.|OK(((
	559	+
	560	+)))
	561	+
	562	+== 7.8 Join Accept Delay2 ==
	563	+
	564	+Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
	565	+
	566	+AT Command:AT+JN2DL
	567	+
	568	+|=(% colspan="3" %)AT+JN2DL
	569	+|**Command Example**|**Function**|**Response**
	570	+|AT+JN2DL=?|Get the Join Accept Delay.|6000(((
	571	+OK
	572	+)))
	573	+|AT+JN2DL=20000|Set the Join Accept Delay.|OK(((
	574	+
	575	+)))
	576	+
	577	+== 7.9 Public Network Mode ==
	578	+
	579	+Feature: Get or Set the public network mode. (0: off, 1: on)
	580	+
	581	+AT Command:AT+PNM
	582	+
	583	+|=(% colspan="3" %)AT+PNM
	584	+|**Command Example**|**Function**|**Response**
	585	+|AT+PNM=?|Get the public network mode.|1(((
	586	+OK
	587	+)))
	588	+|AT+PNM=1|Set the public network mode.|(System will write new value to PNM)(((
	589	+OK
	590	+
	591	+
	592	+)))
	593	+
	594	+== 7.10 Receive Delay1 ==
	595	+
	596	+Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
	597	+
	598	+AT Command:AT+RX1DL
	599	+
	600	+|=(% colspan="3" %)AT+RX1DL
	601	+|**Command Example**|**Function**|**Response**
	602	+|AT+RX1DL=?|Get the delay.|1000(((
	603	+OK
	604	+)))
	605	+|AT+RX1DL=1500|Set the delay.|OK(((
	606	+
	607	+)))
	608	+
	609	+== 7.11Receive Delay2 ==
	610	+
	611	+Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
	612	+
	613	+AT Command:AT+RX2DL
	614	+
	615	+|=(% colspan="3" %)AT+RX2DL
	616	+|**Command Example**|**Function**|**Response**
	617	+|AT+RX2DL=?|Get the delay.|2000(((
	618	+OK
	619	+)))
	620	+|AT+RX2DL=2500|Set the delay.|OK(((
	621	+
	622	+)))
	623	+
	624	+== 7.12 Rx2 Window Data Rate ==
	625	+
	626	+Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
	627	+
	628	+AT Command:AT+RX2DR
	629	+
	630	+|=(% colspan="3" %)AT+RX2DR
	631	+|**Command Example**|**Function**|**Response**
	632	+|AT+RX2DR=?|Get the Rx2 window data rate.|2(((
	633	+OK
	634	+)))
	635	+|AT+RX2DR=6|Set the Rx2 window data rate.|OK(((
	636	+
	637	+)))
	638	+
	639	+== 7.13 Rx2 Window Frequency ==
	640	+
	641	+Feature: Get or Set the Rx2 window frequency
	642	+
	643	+AT Command:AT+RX2FQ
	644	+
	645	+|=(% colspan="3" %)AT+RX2FQ
	646	+|**Command Example**|**Function**|**Response**
	647	+|AT+RX2FQ=?|Get the Rx2 window frequency.|434665000(((
	648	+OK
	649	+)))
	650	+|AT+RX2FQ=434665000|Set the Rx2 window frequency.|OK(((
	651	+
	652	+)))
	653	+
	654	+== 7.14 Transmit Power ==
	655	+
	656	+Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
	657	+
	658	+AT Command:AT+TXP
	659	+
	660	+|=(% colspan="3" %)AT+TXP
	661	+|**Command Example**|**Function**|**Response**
	662	+|AT+TXP=?|Get the Transmit Power.|0(((
	663	+OK
	664	+)))
	665	+|AT+TXP=1|Set the Transmit Power.|OK(((
	666	+
	667	+)))
	668	+
	669	+Downlink Payload. The 4th byte of 0x22 downlink.
	670	+
	671	+If the downlink payload=22000100, it means setting the TXP to 0.
	672	+
	673	+* Example 1: Downlink Payload: 22000102 ~/~/ Set AT+TXP=2.
	674	+* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+TXP=0.
	675	+
	676	+== 7.15 RSSI of the Last Received Packet ==
	677	+
	678	+Feature: Get or Set the Rx2 window frequency
	679	+
	680	+AT Command:AT+RSSI
	681	+
	682	+|=(% colspan="3" %)AT+RSSI
	683	+|**Command Example**|**Function**|**Response**
	684	+|AT+RSSI=?|Get the RSSI of the last received packet.|0(((
	685	+OK
	686	+)))
	687	+
	688	+== 7.16 SNR of the Last Received Packet ==
	689	+
	690	+Feature: Get the SNR of the last received packet
	691	+
	692	+AT Command:AT+SNR
	693	+
	694	+|=(% colspan="3" %)AT+SNR
	695	+|**Command Example**|**Function**|**Response**
	696	+|AT+SNR=?|Get the RSSI of the last received packet.|0(((
	697	+OK
	698	+)))
	699	+
	700	+== 7.17 Application Port ==
	701	+
	702	+Feature: Get or set the application port.
	703	+
	704	+AT Command: AT+PORT
	705	+
	706	+|=(% colspan="3" %)AT+PORT
	707	+|**Command Example**|**Function**|**Response**
	708	+|AT+PORT=?|Get the application port|21(((
	709	+OK
	710	+)))
	711	+|AT+PORT=21|Set the application port|OK
	712	+
	713	+Downlink Command: 0x23
	714	+
	715	+Format: Command Code (0x23) followed by 1 bytes port value.
	716	+
	717	+If the downlink payload=2301, it means set the application port to 1, while type code is 23.
	718	+
	719	+* Example 1: Downlink Payload: 2301 ~/~/ set the application port to 1
	720	+* Example 2: Downlink Payload: 2305 ~/~/ set the application port to 5
	721	+
	722	+== 7.18 Single Channel Mode ==
	723	+
	724	+Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
	725	+
	726	+AT Command: AT+CHS
	727	+
	728	+|=(% colspan="3" %)AT+CHS
	729	+|**Command Example**|**Function**|**Response**
	730	+|AT+CHS=?|Get Frequency for Single Channel Mode|0(((
	731	+OK
	732	+)))
	733	+|AT+CHS=868100000|Set Frequency for Single Channel Mode|OK
	734	+
	735	+== 7.19 Eight Channel Mode ==
	736	+
	737	+Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
	738	+
	739	+AT Command: AT+CHE
	740	+
	741	+|=(% colspan="3" %)AT+CHE
	742	+|**Command Example**|**Function**|**Response**
	743	+|AT+CHE=?|Get eight channels mode|1(((
	744	+902.3 902.5 902.7 902.9 903.1 903.3 903.5 903.7
	745	+
	746	+OK
	747	+)))
	748	+|AT+CHE=1|Set eight channels mode|OK
	749	+
	750	+Downlink Command: 0x24
	751	+
	752	+Format: Command Code (0x24) followed by 1 bytes channel value.
	753	+
	754	+If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
	755	+
	756	+* Example 1: Downlink Payload: 2401 ~/~/ set channel mode to 1
	757	+* Example 2: Downlink Payload: 2405 ~/~/ set channel mode to 5
	758	+
	759	+== 7.20 Get or Set RXwindows1 timeout ==
	760	+
	761	+Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
	762	+
	763	+AT Command: AT+RX1WTO
	764	+
	765	+|=(% colspan="3" %)AT+ RX1WTO
	766	+|**Command Example**|**Function**|**Response**
	767	+|AT+RX1WTO=?|Get RXwindows1 timeout|14(((
	768	+OK
	769	+)))
	770	+|AT+RX1WTO=60|Set RXwindows1 timeout|OK
	771	+
	772	+AT+RX1TWO is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
	773	+
	774	+[[~[~[image:https://wiki.dragino.com/images/thumb/5/51/RX1WTO.JPG/600px-RX1WTO.JPG~|~|alt="RX1WTO.JPG" height="239" width="600"~]~]>>url:https://wiki.dragino.com/index.php/File:RX1WTO.JPG]]
	775	+
	776	+Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
	777	+
	778	+== 7.21 Get or Set RXwindows2 timeout ==
	779	+
	780	+Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
	781	+
	782	+AT Command: AT+RX2WTO
	783	+
	784	+|=(% colspan="3" %)AT+ RX2WTO
	785	+|**Command Example**|**Function**|**Response**
	786	+|AT+RX2WTO=?|Get RXwindows2 timeout|7(((
	787	+OK
	788	+)))
	789	+|AT+RX2WTO=20|Set RXwindows2 timeout|OK
	790	+
	791	+== 7.22 Setting up uplinkdwelltime (as923, au915) ==
	792	+
	793	+Feature: Get or Set uplinkdwelltime
	794	+
	795	+AT Command: AT+DWELLT
	796	+
	797	+|=(% colspan="3" %)AT+DWELLT
	798	+|**Command Example**|**Function**|**Response**
	799	+|AT+DWELLT=?|Get uplinkdwelltime|1(((
	800	+OK
	801	+)))
	802	+|AT+DWELLT=0|Set uplinkdwelltime|OK
	803	+
	804	+Downlink Command: 0x25
	805	+
	806	+Format: Command Code (0x25) followed by 1 bytes state value.
	807	+
	808	+If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
	809	+
	810	+* Example 1: Downlink Payload: 2501 ~/~/ set uplinkdwelltime to 1
	811	+* Example 2: Downlink Payload: 2500 ~/~/ set uplinkdwelltime to 0
	812	+
	813	+== 7.23 Set Packet Receiving Response Level ==
	814	+
	815	+Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
	816	+
	817	+RPL value:
	818	+
	819	+* AT+RPL=0: Device won't immediately reply any downlink commands from platform.
	820	+* AT+RPL=1: Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
	821	+* AT+RPL=2: Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
	822	+* AT+RPL=3: Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
	823	+* AT+RPL=4: Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
	824	+
	825	+Case Analyes:
	826	+
	827	+* For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
	828	+* For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
	829	+* For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
	830	+
	831	+AT Command: AT+RPL
	832	+
	833	+|=(% colspan="3" %)AT+RPL
	834	+|**Command Example**|**Function**|**Response**
	835	+|AT+RPL=?|Get packet receiving response level|1(((
	836	+OK
	837	+)))
	838	+|AT+RPL=0|Set packet receiving response level|OK
	839	+
	840	+Downlink Command: 0x21
	841	+
	842	+Format: Command Code (0x21) followed by 1 bytes level value.
	843	+
	844	+If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
	845	+
	846	+* Example 1: Downlink Payload: 2101 ~/~/ set packet receiving response level to 1
	847	+* Example 2: Downlink Payload: 2102 ~/~/ set packet receiving response level to 2
	848	+
	849	+= 8. AT Commands Combination =
	850	+
	851	+== 8.1 Set a fix RX2DR for downlink window ==
	852	+
	853	+* AT+ADR=0 ~-~-> Disable ADR first
	854	+* AT+RX2DR=xxxx ~-~-> Set xxxx to your wanted DataRate
	855	+
	856	+== 8.2 Use Downlink Command to set a fix uplink DR ==
	857	+
	858	+Downlink Command: 0x22000500
	859	+
	860	+Same as:
	861	+
	862	+* AT+ADR=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Adaptive_Data_Rate]]
	863	+* AT+DR=5 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Data_Rate]]
	864	+* AT+TXP=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Transmit_Power]]