Skip to Content
Version 38.93 by Xiaoling on 2022/05/31 09:21
Show last authors
1 **Contents：**
2
3 {{toc/}}
4
5
6
7 = 1. Introduction =
8
9 Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
10
11 * **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
12 * **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
13
14 (((
15 **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
16
17 )))
18
19 = 2. How to use AT Commands or Downlink command =
20
21 * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22 * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23 ** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24 ** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
25 ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
26
27
28 = 3. Support End Node and firmware version =
29
30 (% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
31 |=(% colspan="3" style="width: 963px;" %)(((
32 Dragino STM32 base hardware Firmware / LoRaWAN stack list
33 )))
34 |(% style="width:187px" %)(((
35 **Model**
36 )))|(% style="width:330px" %)(((
37 **Description**
38 )))|(% style="width:445px" %)(((
39 **Firmware Version <~-~-> Stack Version**
40 )))
41 |(% style="width:187px" %)(((
42 [[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],
43 )))|(% style="width:330px" %)(((
44 Open Source Generic LoRaWAN Sensor Node
45 )))|(% style="width:445px" %)(((
46 (((
47 LSN50 v1.6.0 <~-~-> DR-LWS-003;
48 )))
49
50 (((
51 (((
52 LSN50 v1.7.0 <~-~-> DR-LWS-005; ~-~-> Support since this version
53 )))
54 )))
55 )))
56 |(% style="width:187px" %)(((
57 [[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],
58 )))|(% style="width:330px" %)(((
59 LoRaWAN GPS Tracker
60 )))|(% style="width:445px" %)(((
61 (((
62 LGT92 v1.6.3 <~-~-> DR-LWS-003;
63 )))
64
65 (((
66 (((
67 LGT92 v1.6.4 <~-~-> DR-LWS-005;~-~-> Support since this version
68 )))
69 )))
70 )))
71 |(% style="width:187px" %)(((
72 [[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],
73 )))|(% style="width:330px" %)(((
74 LoRaWAN BLE Indoor Tracker
75 )))|(% style="width:445px" %)(((
76 LBT1 v1.0 <~-~-> DR-LWS-005;
77 )))
78 |(% style="width:187px" %)(((
79 [[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],
80 )))|(% style="width:330px" %)(((
81 LoRaWAN RS485 Modbus Converter
82 )))|(% style="width:445px" %)(((
83 RS485-LN v1.3 <~-~-> DR-LWS-005;
84 )))
85 |(% style="width:187px" %)(((
86 [[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],
87 )))|(% style="width:330px" %)(((
88 LoRaWAN Temperature & Humidity Sensor
89 )))|(% style="width:445px" %)(((
90 (((
91 LHT65 v1.7 <~-~-> DR-LWS-003;
92 )))
93
94 (((
95 (((
96 LHT65 v1.8.0 <~-~-> DR-LWS-005;~-~-> Support since this version
97 )))
98 )))
99 )))
100
101
102
103 = 4. System Management Commands =
104
105 == 4.1 Change Uplink Interval ==
106
107 Feature: Change LoRaWAN End Node Transmit Interval.
108
109 (% class="box infomessage" %)
110 (((
111 **AT Command: AT+TDC**
112 )))
113
114 (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
115 |=(% colspan="3" style="width: 724px;" %)AT+TDC
116 |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
117 |(% style="width:165px" %)AT+TDC=?|(% style="width:227px" %)Show current transmit Interval|(% style="width:329px" %)30000(((
118 OK
119
120 the interval is 30000ms = 30s
121 )))
122 |(% style="width:165px" %)AT+TDC=60000|(% style="width:227px" %)Set Transmit Interval|(% style="width:329px" %)OK(((
123 Set transmit interval to 60000ms = 60 seconds
124 )))
125
126 {{info}}
127 **Downlink Command: 0x01**
128 {{/info}}
129
130 (((
131 Format: Command Code (0x01) followed by 3 bytes time value.
132 )))
133
134 (((
135 If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
136 )))
137
138 * **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
139 * **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
140
141
142
143 == 4.2 Reboot End Node ==
144
145 Feature: Reboot End Node to perform a new OTAA or ABP Join.
146
147 {{info}}
148 **AT Command: ATZ**
149 {{/info}}
150
151 (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
152 |=(% colspan="3" %)ATZ: Trig a reset of the MCU
153 |**Command Example**|**Function**|**Response**
154 |ATZ|Reset MCU|(((
155 Device reset and show booting info
156
157 LSN50 Device/LoRa ST Module
158
159 Image Version: XX
160
161 Frequency Band: XX
162
163 DevEui= XX XX XX XX XX XX XX XX
164
165 <followed by the Tx and Rx information>
166 )))
167
168 {{info}}
169 **Downlink Command: 0x04**
170 {{/info}}
171
172 (((
173 Format: Command Code (0x04) followed by FF.
174 )))
175
176 (((
177 If the downlink payload=**04FF**, the end node will reboot.
178
179
180 )))
181
182 == 4.3 Reset to factory Default ==
183
184 Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
185
186 {{info}}
187 **AT Command: AT+FDR**
188 {{/info}}
189
190 (% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
191 |=(% colspan="3" style="width: 828px;" %)Reset to factory default
192 |(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
193 |(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
194 Device reset to factory default parameters and show booting info
195
196 LSN50 Device/LoRa ST Module
197
198 Image Version: XX
199
200 Frequency Band: XX
201
202 DevEui= XX XX XX XX XX XX XX XX
203
204 Please set the parameters or reset Device to apply change
205 )))
206
207 {{info}}
208 **Downlink Command: 0x04**
209 {{/info}}
210
211 (((
212 Format: Command Code (0x04) followed by FE.
213 )))
214
215 (((
216 If the downlink payload=**04FE**, Reset Parameters to Factory Default, Keys Reserve.
217 )))
218
219
220 == 4.4 Show Firmware Version ==
221
222 Feature: Show firmware version. No downlink command yet.
223
224 {{info}}
225 **AT Command: AT+VER**
226 {{/info}}
227
228 (% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
229 |=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
230 |(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
231 |(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
232 1.3 EU868
233
234 OK
235 )))
236
237 {{info}}
238 **Downlink Command: 0x26 (Valid in 006 stack)**
239 {{/info}}
240
241 (((
242 Downlink Format: 0x26
243 )))
244
245 (((
246 Device will reply with firmware version info, device info. frequency band info. detail please check device user manual. Total 5 bytes Example: If device is of firmware version 1.1.0 Upload: xx ~-~- yy ~-~- zz ~-~- 110 total 5 bytes
247 )))
248
249 (((
250 **xx: Software Type:**
251 )))
252
253 * 0x00 01: LGT92 Version
254 * 0x00 02: LBT1
255 * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
256
257 (((
258 **yy: Frequency Band:**
259 )))
260
261 * 0x01: EU868
262 * 0x02: US915
263 * 0x03: IN865
264 * 0x04: AU915
265 * 0x05: KZ865
266 * 0x06: RU864
267 * 0x07: AS923
268 * 0x08: AS923-1
269 * 0x09: AS923-2
270 * 0xa0: AS923-3
271
272 (((
273 **zz: Subband**
274 )))
275
276 firmware version: v1.1.0 ~-~-> 110
277
278
279 == 4.5 Show System Configure ==
280
281 Feature: Show All configure. No downlink command yet.
282
283 {{info}}
284 **AT Command: AT+CFG**
285 {{/info}}
286
287 (% border="1" style="background-color:#ffffcc; color:green; width:599.222px" %)
288 |=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations
289 |(% style="width:160px" %)**Command Example**|(% style="width:154px" %)**Function**|(% style="width:280px" %)**Response**
290 |(% style="width:160px" %)AT+CFG|(% style="width:154px" %)Show all configures|(% style="width:280px" %)(((
291 AT+DEUI = XX XX XX XX XX XX XX XX
292
293 AT+DADDR=XXXXXXXX
294
295 ……….
296
297 AT+RX2WTO=X
298
299 AT+CHS=868100000
300
301 OK
302 )))
303
304
305
306 = 5. Keys, IDs and EUIs management =
307
308 == 5.1 Application EUI ==
309
310 Feature: Get or Set the Application EUI.
311
312 {{info}}
313 **AT Command: AT+APPEUI**
314 {{/info}}
315
316 (% border="1" style="background-color:#ffffcc; color:green; width:686.222px" %)
317 |=(% colspan="3" style="width: 683px;" %)AT+APPEUI
318 |(% style="width:305px" %)**Command Example**|(% style="width:186px" %)**Function**|(% style="width:191px" %)**Response**
319 |(% style="width:305px" %)AT+APPEUI=?|(% style="width:186px" %)Get the Application EUI|(% style="width:191px" %)00 b3 d5 00 00 00 00 00(((
320 OK
321 )))
322 |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
323
324
325
326 == 5.2 Application Key ==
327
328 Feature: Get or Set the Application Key.
329
330 {{info}}
331 **AT Command: AT+APPKEY**
332 {{/info}}
333
334 (% border="1" style="background-color:#ffffcc; color:green; width:976.222px" %)
335 |=(% colspan="3" style="width: 973px;" %)AT+APPKEY
336 |(% style="width:441px" %)**Command Example**|(% style="width:180px" %)**Function**|(% style="width:350px" %)**Response**
337 |(% style="width:441px" %)AT+APPKEY=?|(% style="width:180px" %)Get the Application Key|(% style="width:350px" %)00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35(((
338 OK
339 )))
340 |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
341
342
343 == 5.3 Application Session Key ==
344
345 Feature: Get or Set the Application Session Key.
346
347 {{info}}
348 **AT Command: AT+APPSKEY**
349 {{/info}}
350
351 (% border="1" style="background-color:#ffffcc; color:green; width:1040.22px" %)
352 |=(% colspan="3" style="width: 1037px;" %)AT+APPSKEY
353 |(% style="width:451px" %)**Command Example**|(% style="width:231px" %)**Function**|(% style="width:354px" %)**Response**
354 |(% style="width:451px" %)AT+APPSKEY=?|(% style="width:231px" %)Get the Application Session Key|(% style="width:354px" %)00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2(((
355 OK
356 )))
357 |(% style="width:451px" %)AT+APPSKEY=00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2|(% style="width:231px" %)Set the Application Session Key|(% style="width:354px" %)(While Error in format, return AT_PARAM_ERROR)(((
358 OK
359 )))
360
361
362 == 5.4 Device Address ==
363
364 Feature: Get or Set the Device Address.
365
366 {{info}}
367 **AT Command: AT+DADDR**
368 {{/info}}
369
370 (% border="1" style="background-color:#ffffcc; color:green; width:795.222px" %)
371 |=(% colspan="3" style="width: 792px;" %)AT+DADDR
372 |(% style="width:192px" %)**Command Example**|(% style="width:241px" %)**Function**|(% style="width:359px" %)**Response**
373 |(% style="width:192px" %)AT+DADDR=?|(% style="width:241px" %)Get the Application Session Key.|(% style="width:359px" %)(While Error in format, return AT_PARAM_ERROR)(((
374 A8 40 41 FF
375
376 OK
377 )))
378 |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
379
380
381 == 5.5 Device EUI ==
382
383 Feature: Get or Set the Device EUI.
384
385 {{info}}
386 **AT Command: AT+DEUI**
387 {{/info}}
388
389 (% border="1" style="background-color:#ffffcc; color:green; width:1035.22px" %)
390 |=(% colspan="3" style="width: 1032px;" %)AT+DEUI
391 |(% style="width:250px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:634px" %)**Response**
392 |(% style="width:250px" %)AT+DEUI=?|(% style="width:147px" %)Get the Device EUI.|(% style="width:634px" %)00 44 34 22 33 45 55 55(((
393 OK
394 )))
395 |(% style="width:250px" %)AT+DEUI=A8 40 41 FF FF 12 34 56|(% style="width:147px" %)Set the Device EUI.|(% style="width:634px" %)(System will write new value to Device EUI,While Error in format, return AT_PARAM_ERROR)(((
396 OK
397 )))
398
399
400 == 5.6 Network ID ==
401
402 Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
403
404 {{info}}
405 **AT Command: AT+NWKID**
406 {{/info}}
407
408 (% border="1" style="background-color:#ffffcc; color:green; width:448.222px" %)
409 |=(% colspan="3" style="width: 445px;" %)AT+NWKID
410 |(% style="width:191px" %)**Command Example**|(% style="width:153px" %)**Function**|(% style="width:101px" %)**Response**
411 |(% style="width:191px" %)AT+NWKID=?|(% style="width:153px" %)Get the Network ID.|(% style="width:101px" %)a8 40 41 ff(((
412 OK
413 )))
414 |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
415
416
417 == 5.7 Network Session Key ==
418
419 Feature: Get or Set the Network Session Key
420
421 {{info}}
422 **AT Command: AT+NWKSKEY**
423 {{/info}}
424
425 (% border="1" style="background-color:#ffffcc; color:green; width:1017.22px" %)
426 |=(% colspan="3" style="width: 1014px;" %)AT+NWKSKEY
427 |(% style="width:455px" %)**Command Example**|(% style="width:215px" %)**Function**|(% style="width:343px" %)**Response**
428 |(% style="width:455px" %)AT+NWKSKEY=?|(% style="width:215px" %)Get the Network Session Key.|(% style="width:343px" %)00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92(((
429 OK
430 )))
431 |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
432
433
434 = 6. Joining and sending date on LoRaWAN network =
435
436 == 6.1 Confirm Mode ==
437
438 Feature: Get or Set the confirmation mode (0-1).
439
440 {{info}}
441 **AT Command: AT+CFM**
442 {{/info}}
443
444 (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
445 |=(% colspan="3" style="width: 707px;" %)AT+CFM
446 |(% style="width:155px" %)**Command Example**|(% style="width:205px" %)**Function**|(% style="width:346px" %)**Response**
447 |(% style="width:155px" %)AT+CFM=?|(% style="width:205px" %)Get the confirmation mode|(% style="width:346px" %)0(((
448 OK
449 )))
450 |(% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK
451 |(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
452
453 Downlink Command: 0x05
454
455 Format: Command Code (0x05) followed by 2 bytes mode value.
456
457 If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
458
459 * Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
460 * Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
461
462
463 == 6.2 Confirm Status ==
464
465 Feature: Get confirmation status of the last AT+SEND (0-1).
466
467 {{info}}
468 **AT Command: AT+CFS**
469 {{/info}}
470
471 (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
472 |=(% colspan="3" style="width: 531px;" %)AT+CFS
473 |(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:178px" %)**Response**
474 |(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:178px" %)0(((
475 OK
476 )))
477
478
479 == 6.3 Join LoRa® Network ==
480
481 Feature: Join network.
482
483 {{info}}
484 **AT Command: AT+JOIN**
485 {{/info}}
486
487 (% border="1" style="background-color:#ffffcc; color:green; width:647.222px" %)
488 |=(% colspan="3" style="width: 644px;" %)AT+JOIN
489 |(% style="width:163px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:334px" %)**Response**
490 |(% style="width:163px" %)AT+JOIN ?|(% style="width:147px" %)Get imformation.|(% style="width:334px" %)AT+JOIN: Join network(((
491 OK
492
493 While Error in format, return AT_BUSY_ERROR
494 )))
495
496
497
498 == 6.4 LoRa® Network Join Mode ==
499
500 Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
501
502 {{info}}
503 **AT Command: AT+NJM**
504 {{/info}}
505
506 (% border="1" style="background-color:#ffffcc; color:green; width:753.222px" %)
507 |=(% colspan="3" style="width: 750px;" %)AT+NJM
508 |(% style="width:162px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:361px" %)**Response**
509 |(% style="width:162px" %)AT+NJM=?|(% style="width:227px" %)Get the Network Join Mode|(% style="width:361px" %)1(((
510 OK
511 )))
512 |(% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK
513 |(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
514
515 {{info}}
516 **Downlink Command: 0x20**
517 {{/info}}
518
519 Format: Command Code (0x20) followed by 1 bytes mode value.
520
521 If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
522
523 * **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=O
524 * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
525
526
527
528 == 6.5 LoRa® Network Join Status ==
529
530 Feature: LoRa® Network Join Status.
531
532 {{info}}
533 **AT Command: AT+NJS**
534 {{/info}}
535
536 (% border="1" style="background-color:#ffffcc; color:green; width:498.222px" %)
537 |=(% colspan="3" style="width: 495px;" %)AT+NJS
538 |(% style="width:169px" %)**Command Example**|(% style="width:164px" %)**Function**|(% style="width:161px" %)**Response**
539 |(% style="width:169px" %)AT+NJS=?|(% style="width:164px" %)Get the join status.|(% style="width:161px" %)0(((
540 OK
541 )))
542
543
544
545 == 6.6 Print Last Received Data in Raw Format ==
546
547 Feature: Print Last Received Data in Raw Format<port:data>.
548
549 {{info}}
550 **AT Command: AT+RECV**
551 {{/info}}
552
553 (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
554 |=(% colspan="3" style="width: 584px;" %)AT+RECV
555 |(% style="width:161px" %)**Command Example**|(% style="width:272px" %)**Function**|(% style="width:150px" %)**Response**
556 |(% style="width:161px" %)AT+RECV=?|(% style="width:272px" %)print last received data in raw format.|(% style="width:150px" %)0:(((
557 OK
558 )))
559
560
561
562 == 6.7 Print Last Received Data in Binary Format ==
563
564 Feature: Print Last Received Data in Binary Format<port:data>.
565
566 {{info}}
567 **AT Command: AT+RECVB**
568 {{/info}}
569
570 (% border="1" style="background-color:#ffffcc; color:green; width:793.222px" %)
571 |=(% colspan="3" style="width: 790px;" %)AT+RECVB
572 |(% style="width:173px" %)**Command Example**|(% style="width:497px" %)**Function**|(% style="width:120px" %)**Response**
573 |(% style="width:173px" %)AT+RECVB=?|(% style="width:497px" %)print last received data in binary format (with hexadecimal values).|(% style="width:120px" %)2: 0010(((
574 OK
575 )))
576
577
578
579 == 6.8 Send Text Data ==
580
581 Feature: Send Text Data<port:data>.
582
583 {{info}}
584 **AT Command: AT+SEND**
585 {{/info}}
586
587 (% border="1" style="background-color:#ffffcc; color:green; width:991.222px" %)
588 |=(% colspan="3" style="width: 988px;" %)AT+SEND
589 |(% style="width:201px" %)**Command Example**|(% style="width:340px" %)**Function**|(% style="width:446px" %)**Response**
590 |(% style="width:201px" %)AT+SEND=12:hello world|(% style="width:340px" %)Send text data along with the application port.|(% style="width:446px" %)OK(((
591 While Error in format, return
592
593 AT_BUSY_ERROR/AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
594
595
596 )))
597
598
599
600 == 6.9 Send Hexadecimal Data ==
601
602 Feature: Send hexadecimal data along with the application port.
603
604 {{info}}
605 **AT Command: AT+SENDB**
606 {{/info}}
607
608 (% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
609 |=(% colspan="3" style="width: 1117px;" %)AT+SENDB
610 |(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
611 |(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK
612 |(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)While Error in format, return(((
613 AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
614
615
616 )))
617
618
619
620 = 7. LoRaWAN network management =
621
622 == 7.1 Adaptive Data Rate ==
623
624 Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on).
625
626 {{info}}
627 **AT Command: AT+ADR**
628 {{/info}}
629
630 (% border="1" style="background-color:#ffffcc; color:green; width:683.222px" %)
631 |=(% colspan="3" style="width: 680px;" %)AT+ADR
632 |(% style="width:162px" %)**Command Example**|(% style="width:266px" %)**Function**|(% style="width:250px" %)**Response**
633 |(% style="width:162px" %)AT+ADR=?|(% style="width:266px" %)Get the Adaptive Data Rate setting.|(% style="width:250px" %)1(((
634 OK
635 )))
636 |(% style="width:162px" %)AT+ADR=0|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)OK
637 |(% style="width:162px" %)AT+ADR=2|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)While Error in format, return(((
638 AT_PARAM_ERROR
639 )))
640
641 {{info}}
642 **Downlink Command: 0x22**
643 {{/info}}
644
645
646 If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
647
648 * **Example 1**: Downlink Payload: **2201** ~/~/ Set AT+ADR=1.
649 * **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
650
651
652
653 == 7.2 LoRa® Class ==
654
655 Feature: Get or Set the Device Class(Currently only support class A, class C).
656
657 {{info}}
658 **AT Command:AT+CLASS**
659 {{/info}}
660
661 (% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
662 |=(% colspan="3" style="width: 504px;" %)AT+CLASS
663 |(% style="width:163px" %)**Command Example**|(% style="width:166px" %)**Function**|(% style="width:175px" %)**Response**
664 |(% style="width:163px" %)AT+CLASS=?|(% style="width:166px" %)Get the Device Class.|(% style="width:175px" %)A(((
665 OK
666 )))
667 |(% style="width:163px" %)AT+CLASS=C|(% style="width:166px" %)Set the Device Class.|(% style="width:175px" %)OK(((
668
669 )))
670
671
672
673 == 7.3 Duty Cycle Setting ==
674
675 Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
676
677 {{info}}
678 **AT Command:AT+DCS**
679 {{/info}}
680
681 (% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
682 |=(% colspan="3" style="width: 512px;" %)AT+DCS
683 |(% style="width:165px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:107px" %)**Response**
684 |(% style="width:165px" %)AT+DCS=?|(% style="width:239px" %)Get the ETSI Duty Cycle setting.|(% style="width:107px" %)1(((
685 OK
686 )))
687 |(% style="width:165px" %)AT+DCS=1|(% style="width:239px" %)Set the ETSI Duty Cycle setting.|(% style="width:107px" %)OK(((
688
689 )))
690
691
692
693 == 7.4 Data Rate ==
694
695 Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
696
697 {{info}}
698 **AT Command: AT+DR**
699 {{/info}}
700
701 (% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
702 |=(% colspan="3" style="width: 463px;" %)AT+DR
703 |(% style="width:156px" %)**Command Example**|(% style="width:167px" %)**Function**|(% style="width:140px" %)**Response**
704 |(% style="width:156px" %)AT+DR=?|(% style="width:167px" %)Get the Data Rate.|(% style="width:140px" %)5(((
705 OK
706 )))
707 |(% style="width:156px" %)AT+DR=2|(% style="width:167px" %)Set the Data Rate.|(% style="width:140px" %)OK(((
708
709 )))
710
711 {{info}}
712 **Downlink Command: 0x2200aaFF**
713 {{/info}}
714
715
716 If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
717
718 * **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
719 * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
720
721 == 7.5 Frame Counter Downlink ==
722
723 Feature: Get or Set the Frame Counter Downlink.
724
725 {{info}}
726 **AT Command:AT+FCD**
727 {{/info}}
728
729 (% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
730 |=(% colspan="3" style="width: 690px;" %)AT+FCD
731 |(% style="width:162px" %)**Command Example**|(% style="width:258px" %)**Function**|(% style="width:269px" %)**Response**
732 |(% style="width:162px" %)AT+FCD=?|(% style="width:258px" %)Get the Frame Counter Downlink.|(% style="width:269px" %)0(((
733 OK
734 )))
735 |(% style="width:162px" %)AT+FCD=10|(% style="width:258px" %)Set the Frame Counter Downlink.|(% style="width:269px" %)(System will write new value to FCD)(((
736 OK
737
738
739 )))
740
741 == 7.6 Frame Counter Uplink ==
742
743 Feature: Get or Set the Frame Counter Uplink.
744
745 {{info}}
746 **AT Command:AT+FCU**
747 {{/info}}
748
749 (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
750 |=(% colspan="3" style="width: 531px;" %)AT+FCU
751 |(% style="width:177px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:113px" %)**Response**
752 |(% style="width:177px" %)AT+FCU=?|(% style="width:239px" %)Get the Frame Counter Uplink.|(% style="width:113px" %)0(((
753 OK
754 )))
755 |(% style="width:177px" %)AT+FCU=10|(% style="width:239px" %)Set the Frame Counter Uplink.|(% style="width:113px" %)OK(((
756
757 )))
758
759 == 7.7 Join Accept Delay1 ==
760
761 Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
762
763 {{info}}
764 **AT Command:AT+JN1DL**
765 {{/info}}
766
767 (% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
768 |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
769 |(% style="width:164px" %)**Command Example**|(% style="width:229px" %)**Function**|(% style="width:140px" %)**Response**
770 |(% style="width:164px" %)AT+JN1DL=?|(% style="width:229px" %)Get the Join Accept Delay.|(% style="width:140px" %)5000(((
771 OK
772 )))
773 |(% style="width:164px" %)AT+JN1DL=10000|(% style="width:229px" %)Set the Join Accept Delay.|(% style="width:140px" %)OK(((
774
775 )))
776
777 == 7.8 Join Accept Delay2 ==
778
779 Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
780
781 {{info}}
782 **AT Command:AT+JN2DL**
783 {{/info}}
784
785 (% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
786 |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
787 |(% style="width:160px" %)**Command Example**|(% style="width:228px" %)**Function**|(% style="width:146px" %)**Response**
788 |(% style="width:160px" %)AT+JN2DL=?|(% style="width:228px" %)Get the Join Accept Delay.|(% style="width:146px" %)6000(((
789 OK
790 )))
791 |(% style="width:160px" %)AT+JN2DL=20000|(% style="width:228px" %)Set the Join Accept Delay.|(% style="width:146px" %)OK(((
792
793 )))
794
795 == 7.9 Public Network Mode ==
796
797 Feature: Get or Set the public network mode. (0: off, 1: on)
798
799 {{info}}
800 **AT Command:AT+PNM**
801 {{/info}}
802
803 (% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
804 |=(% colspan="3" style="width: 664px;" %)AT+PNM
805 |(% style="width:166px" %)**Command Example**|(% style="width:225px" %)**Function**|(% style="width:272px" %)**Response**
806 |(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
807 OK
808 )))
809 |(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)Set the public network mode.|(% style="width:272px" %)(System will write new value to PNM)(((
810 OK
811
812
813 )))
814
815 == 7.10 Receive Delay1 ==
816
817 Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
818
819 {{info}}
820 **AT Command:AT+RX1DL**
821 {{/info}}
822
823 (% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
824 |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
825 |(% style="width:155px" %)**Command Example**|(% style="width:128px" %)**Function**|(% style="width:122px" %)**Response**
826 |(% style="width:155px" %)AT+RX1DL=?|(% style="width:128px" %)Get the delay.|(% style="width:122px" %)1000(((
827 OK
828 )))
829 |(% style="width:155px" %)AT+RX1DL=1500|(% style="width:128px" %)Set the delay.|(% style="width:122px" %)OK(((
830
831 )))
832
833 == 7.11 Receive Delay2 ==
834
835 Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
836
837 {{info}}
838 **AT Command:AT+RX2DL**
839 {{/info}}
840
841 (% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
842 |=(% colspan="3" style="width: 478px;" %)AT+RX2DL
843 |(% style="width:175px" %)**Command Example**|(% style="width:152px" %)**Function**|(% style="width:150px" %)**Response**
844 |(% style="width:175px" %)AT+RX2DL=?|(% style="width:152px" %)Get the delay.|(% style="width:150px" %)2000(((
845 OK
846 )))
847 |(% style="width:175px" %)AT+RX2DL=2500|(% style="width:152px" %)Set the delay.|(% style="width:150px" %)OK(((
848
849 )))
850
851 == 7.12 Rx2 Window Data Rate ==
852
853 Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
854
855 {{info}}
856 **AT Command:AT+RX2DR**
857 {{/info}}
858
859 (% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
860 |=(% colspan="3" style="width: 522px;" %)AT+RX2DR
861 |(% style="width:160px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:130px" %)**Response**
862 |(% style="width:160px" %)AT+RX2DR=?|(% style="width:232px" %)Get the Rx2 window data rate.|(% style="width:130px" %)2(((
863 OK
864 )))
865 |(% style="width:160px" %)AT+RX2DR=6|(% style="width:232px" %)Set the Rx2 window data rate.|(% style="width:130px" %)OK(((
866
867 )))
868
869 == 7.13 Rx2 Window Frequency ==
870
871 Feature: Get or Set the Rx2 window frequency
872
873 {{info}}
874 **AT Command:AT+RX2FQ**
875 {{/info}}
876
877 (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
878 |=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
879 |(% style="width:183px" %)**Command Example**|(% style="width:240px" %)**Function**|(% style="width:160px" %)**Response**
880 |(% style="width:183px" %)AT+RX2FQ=?|(% style="width:240px" %)Get the Rx2 window frequency.|(% style="width:160px" %)434665000(((
881 OK
882 )))
883 |(% style="width:183px" %)AT+RX2FQ=434665000|(% style="width:240px" %)Set the Rx2 window frequency.|(% style="width:160px" %)OK(((
884
885 )))
886
887 == 7.14 Transmit Power ==
888
889 Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
890
891 {{info}}
892 **AT Command:AT+TXP**
893 {{/info}}
894
895 (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
896 |=(% colspan="3" style="width: 462px;" %)AT+TXP
897 |(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
898 |(% style="width:161px" %)AT+TXP=?|(% style="width:189px" %)Get the Transmit Power.|(% style="width:112px" %)0(((
899 OK
900 )))
901 |(% style="width:161px" %)AT+TXP=1|(% style="width:189px" %)Set the Transmit Power.|(% style="width:112px" %)OK(((
902
903 )))
904
905 Downlink Payload. The 4th byte of 0x22 downlink.
906
907 If the downlink payload=22000100, it means setting the TXP to 0.
908
909 * **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
910 * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
911
912 == 7.15 RSSI of the Last Received Packet ==
913
914 Feature: Get or Set the Rx2 window frequency
915
916 {{info}}
917 **AT Command:AT+RSSI**
918 {{/info}}
919
920 (% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %)
921 |=(% colspan="3" style="width: 554px;" %)AT+RSSI
922 |(% style="width:164px" %)**Command Example**|(% style="width:289px" %)**Function**|(% style="width:100px" %)**Response**
923 |(% style="width:164px" %)AT+RSSI=?|(% style="width:289px" %)Get the RSSI of the last received packet.|(% style="width:100px" %)0(((
924 OK
925 )))
926
927 == 7.16 SNR of the Last Received Packet ==
928
929 Feature: Get the SNR of the last received packet
930
931 {{info}}
932 **AT Command:AT+SNR**
933 {{/info}}
934
935 (% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
936 |=(% colspan="3" style="width: 568px;" %)AT+SNR
937 |(% style="width:164px" %)**Command Example**|(% style="width:290px" %)**Function**|(% style="width:113px" %)**Response**
938 |(% style="width:164px" %)AT+SNR=?|(% style="width:290px" %)Get the RSSI of the last received packet.|(% style="width:113px" %)0(((
939 OK
940 )))
941
942 == 7.17 Application Port ==
943
944 Feature: Get or set the application port.
945
946 {{info}}
947 **AT Command: AT+PORT**
948 {{/info}}
949
950 (% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %)
951 |=(% colspan="3" style="width: 497px;" %)AT+PORT
952 |(% style="width:157px" %)**Command Example**|(% style="width:204px" %)**Function**|(% style="width:135px" %)**Response**
953 |(% style="width:157px" %)AT+PORT=?|(% style="width:204px" %)Get the application port|(% style="width:135px" %)21(((
954 OK
955 )))
956 |(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
957
958 {{info}}
959 **Downlink Command: 0x23**
960 {{/info}}
961
962 Format: Command Code (0x23) followed by 1 bytes port value.
963
964 If the downlink payload=2301, it means set the application port to 1, while type code is 23.
965
966 * **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
967 * **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
968
969 == 7.18 Single Channel Mode ==
970
971 Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
972
973 {{info}}
974 **AT Command: AT+CHS**
975 {{/info}}
976
977 (% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %)
978 |=(% colspan="3" style="width: 600px;" %)AT+CHS
979 |(% style="width:182px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:122px" %)**Response**
980 |(% style="width:182px" %)AT+CHS=?|(% style="width:295px" %)Get Frequency for Single Channel Mode|(% style="width:122px" %)0(((
981 OK
982 )))
983 |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
984
985 == 7.19 Eight Channel Mode ==
986
987 Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
988
989 {{info}}
990 **AT Command: AT+CHE**
991 {{/info}}
992
993 (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
994 |=(% colspan="3" style="width: 707px;" %)AT+CHE
995 |(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
996 |(% style="width:160px" %)AT+CHE=?|(% style="width:198px" %)Get eight channels mode|(% style="width:349px" %)1(((
997 902.3 902.5 902.7 902.9 903.1 903.3 903.5 903.7
998
999 OK
1000 )))
1001 |(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
1002
1003 {{info}}
1004 **Downlink Command: 0x24**
1005 {{/info}}
1006
1007 Format: Command Code (0x24) followed by 1 bytes channel value.
1008
1009 If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1010
1011 * **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
1012 * **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1013
1014 == 7.20 Get or Set RXwindows1 timeout ==
1015
1016 Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1017
1018 {{info}}
1019 **AT Command: AT+RX1WTO**
1020 {{/info}}
1021
1022 (% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %)
1023 |=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO
1024 |(% style="width:163px" %)**Command Example**|(% style="width:201px" %)**Function**|(% style="width:93px" %)**Response**
1025 |(% style="width:163px" %)AT+RX1WTO=?|(% style="width:201px" %)Get RXwindows1 timeout|(% style="width:93px" %)14(((
1026 OK
1027 )))
1028 |(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK
1029
1030 (((
1031 **AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1032 )))
1033
1034 [[image:image-20220526162535-1.png]]
1035
1036 (((
1037 Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1038
1039
1040 )))
1041
1042 == 7.21 Get or Set RXwindows2 timeout ==
1043
1044 Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1045
1046 {{info}}
1047 **AT Command: AT+RX2WTO**
1048 {{/info}}
1049
1050 (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1051 |=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO
1052 |(% style="width:190px" %)**Command Example**|(% style="width:199px" %)**Function**|(% style="width:104px" %)**Response**
1053 |(% style="width:190px" %)AT+RX2WTO=?|(% style="width:199px" %)Get RXwindows2 timeout|(% style="width:104px" %)7(((
1054 OK
1055 )))
1056 |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1057
1058 == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1059
1060 Feature: Get or Set uplinkdwelltime
1061
1062 {{info}}
1063 **AT Command: AT+DWELLT**
1064 {{/info}}
1065
1066 (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1067 |=(% colspan="3" style="width: 494px;" %)AT+DWELLT
1068 |(% style="width:183px" %)**Command Example**|(% style="width:179px" %)**Function**|(% style="width:131px" %)**Response**
1069 |(% style="width:183px" %)AT+DWELLT=?|(% style="width:179px" %)Get uplinkdwelltime|(% style="width:131px" %)1(((
1070 OK
1071 )))
1072 |(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
1073
1074 {{info}}
1075 **Downlink Command: 0x25**
1076 {{/info}}
1077
1078 Format: Command Code (0x25) followed by 1 bytes state value.
1079
1080 If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1081
1082 * **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1083 * **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1084
1085 == 7.23 Set Packet Receiving Response Level ==
1086
1087 Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1088
1089 RPL value:
1090
1091 * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1092 * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
1093 * **AT+RPL=2:** Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
1094 * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1095 * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1096
1097 Case Analyes:
1098
1099 * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1100 * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1101 * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1102
1103 {{info}}
1104 **AT Command: AT+RPL**
1105 {{/info}}
1106
1107 (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1108 |=(% colspan="3" style="width: 533px;" %)AT+RPL
1109 |(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1110 |(% style="width:160px" %)AT+RPL=?|(% style="width:263px" %)Get packet receiving response level|(% style="width:109px" %)1(((
1111 OK
1112 )))
1113 |(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
1114
1115 {{info}}
1116 **Downlink Command: 0x21**
1117 {{/info}}
1118
1119 Format: Command Code (0x21) followed by 1 bytes level value.
1120
1121 If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1122
1123 * **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1124 * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1125
1126 = 8. AT Commands Combination =
1127
1128 == 8.1 Set a fix RX2DR for downlink window ==
1129
1130 * **AT+ADR=0 **~-~-> Disable ADR first
1131 * **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1132
1133 == 8.2 Use Downlink Command to set a fix uplink DR ==
1134
1135 {{info}}
1136 **Downlink Command: 0x22000500**
1137 {{/info}}
1138
1139 Same as:
1140
1141 * AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1142 * AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1143 * AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]