Skip to Content
Version 38.88 by Xiaoling on 2022/05/31 09:21
Show last authors
1 **Contents：**
2
3 {{toc/}}
4
5
6
7 = 1. Introduction =
8
9 Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
10
11 * **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
12 * **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
13
14 (((
15 **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
16
17 )))
18
19 = 2. How to use AT Commands or Downlink command =
20
21 * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22 * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23 ** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24 ** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
25 ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
26
27
28 = 3. Support End Node and firmware version =
29
30 (% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
31 |=(% colspan="3" style="width: 963px;" %)(((
32 Dragino STM32 base hardware Firmware / LoRaWAN stack list
33 )))
34 |(% style="width:187px" %)(((
35 **Model**
36 )))|(% style="width:330px" %)(((
37 **Description**
38 )))|(% style="width:445px" %)(((
39 **Firmware Version <~-~-> Stack Version**
40 )))
41 |(% style="width:187px" %)(((
42 [[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],
43 )))|(% style="width:330px" %)(((
44 Open Source Generic LoRaWAN Sensor Node
45 )))|(% style="width:445px" %)(((
46 (((
47 LSN50 v1.6.0 <~-~-> DR-LWS-003;
48 )))
49
50 (((
51 (((
52 LSN50 v1.7.0 <~-~-> DR-LWS-005; ~-~-> Support since this version
53 )))
54 )))
55 )))
56 |(% style="width:187px" %)(((
57 [[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],
58 )))|(% style="width:330px" %)(((
59 LoRaWAN GPS Tracker
60 )))|(% style="width:445px" %)(((
61 (((
62 LGT92 v1.6.3 <~-~-> DR-LWS-003;
63 )))
64
65 (((
66 (((
67 LGT92 v1.6.4 <~-~-> DR-LWS-005;~-~-> Support since this version
68 )))
69 )))
70 )))
71 |(% style="width:187px" %)(((
72 [[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],
73 )))|(% style="width:330px" %)(((
74 LoRaWAN BLE Indoor Tracker
75 )))|(% style="width:445px" %)(((
76 LBT1 v1.0 <~-~-> DR-LWS-005;
77 )))
78 |(% style="width:187px" %)(((
79 [[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],
80 )))|(% style="width:330px" %)(((
81 LoRaWAN RS485 Modbus Converter
82 )))|(% style="width:445px" %)(((
83 RS485-LN v1.3 <~-~-> DR-LWS-005;
84 )))
85 |(% style="width:187px" %)(((
86 [[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],
87 )))|(% style="width:330px" %)(((
88 LoRaWAN Temperature & Humidity Sensor
89 )))|(% style="width:445px" %)(((
90 (((
91 LHT65 v1.7 <~-~-> DR-LWS-003;
92 )))
93
94 (((
95 (((
96 LHT65 v1.8.0 <~-~-> DR-LWS-005;~-~-> Support since this version
97 )))
98 )))
99 )))
100
101
102
103 = 4. System Management Commands =
104
105 == 4.1 Change Uplink Interval ==
106
107 Feature: Change LoRaWAN End Node Transmit Interval.
108
109 (% class="box infomessage" %)
110 (((
111 **AT Command: AT+TDC**
112 )))
113
114 (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
115 |=(% colspan="3" style="width: 724px;" %)AT+TDC
116 |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
117 |(% style="width:165px" %)AT+TDC=?|(% style="width:227px" %)Show current transmit Interval|(% style="width:329px" %)30000(((
118 OK
119
120 the interval is 30000ms = 30s
121 )))
122 |(% style="width:165px" %)AT+TDC=60000|(% style="width:227px" %)Set Transmit Interval|(% style="width:329px" %)OK(((
123 Set transmit interval to 60000ms = 60 seconds
124 )))
125
126 {{info}}
127 **Downlink Command: 0x01**
128 {{/info}}
129
130 (((
131 Format: Command Code (0x01) followed by 3 bytes time value.
132 )))
133
134 (((
135 If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
136 )))
137
138 * **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
139 * **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
140
141
142
143 == 4.2 Reboot End Node ==
144
145 Feature: Reboot End Node to perform a new OTAA or ABP Join.
146
147 {{info}}
148 **AT Command: ATZ**
149 {{/info}}
150
151 (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
152 |=(% colspan="3" %)ATZ: Trig a reset of the MCU
153 |**Command Example**|**Function**|**Response**
154 |ATZ|Reset MCU|(((
155 Device reset and show booting info
156
157 LSN50 Device/LoRa ST Module
158
159 Image Version: XX
160
161 Frequency Band: XX
162
163 DevEui= XX XX XX XX XX XX XX XX
164
165 <followed by the Tx and Rx information>
166 )))
167
168 {{info}}
169 **Downlink Command: 0x04**
170 {{/info}}
171
172 (((
173 Format: Command Code (0x04) followed by FF.
174 )))
175
176 (((
177 If the downlink payload=**04FF**, the end node will reboot.
178
179
180 )))
181
182 == 4.3 Reset to factory Default ==
183
184 Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
185
186 {{info}}
187 **AT Command: AT+FDR**
188 {{/info}}
189
190 (% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
191 |=(% colspan="3" style="width: 828px;" %)Reset to factory default
192 |(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
193 |(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
194 Device reset to factory default parameters and show booting info
195
196 LSN50 Device/LoRa ST Module
197
198 Image Version: XX
199
200 Frequency Band: XX
201
202 DevEui= XX XX XX XX XX XX XX XX
203
204 Please set the parameters or reset Device to apply change
205 )))
206
207 {{info}}
208 **Downlink Command: 0x04**
209 {{/info}}
210
211 (((
212 Format: Command Code (0x04) followed by FE.
213 )))
214
215 (((
216 If the downlink payload=**04FE**, Reset Parameters to Factory Default, Keys Reserve.
217 )))
218
219
220 == 4.4 Show Firmware Version ==
221
222 Feature: Show firmware version. No downlink command yet.
223
224 {{info}}
225 **AT Command: AT+VER**
226 {{/info}}
227
228 (% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
229 |=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
230 |(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
231 |(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
232 1.3 EU868
233
234 OK
235 )))
236
237 {{info}}
238 **Downlink Command: 0x26 (Valid in 006 stack)**
239 {{/info}}
240
241 (((
242 Downlink Format: 0x26
243 )))
244
245 (((
246 Device will reply with firmware version info, device info. frequency band info. detail please check device user manual. Total 5 bytes Example: If device is of firmware version 1.1.0 Upload: xx ~-~- yy ~-~- zz ~-~- 110 total 5 bytes
247 )))
248
249 (((
250 **xx: Software Type:**
251 )))
252
253 * 0x00 01: LGT92 Version
254 * 0x00 02: LBT1
255 * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
256
257 (((
258 **yy: Frequency Band:**
259 )))
260
261 * 0x01: EU868
262 * 0x02: US915
263 * 0x03: IN865
264 * 0x04: AU915
265 * 0x05: KZ865
266 * 0x06: RU864
267 * 0x07: AS923
268 * 0x08: AS923-1
269 * 0x09: AS923-2
270 * 0xa0: AS923-3
271
272 (((
273 **zz: Subband**
274 )))
275
276 firmware version: v1.1.0 ~-~-> 110
277
278
279 == 4.5 Show System Configure ==
280
281 Feature: Show All configure. No downlink command yet.
282
283 {{info}}
284 **AT Command: AT+CFG**
285 {{/info}}
286
287 (% border="1" style="background-color:#ffffcc; color:green; width:599.222px" %)
288 |=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations
289 |(% style="width:160px" %)**Command Example**|(% style="width:154px" %)**Function**|(% style="width:280px" %)**Response**
290 |(% style="width:160px" %)AT+CFG|(% style="width:154px" %)Show all configures|(% style="width:280px" %)(((
291 AT+DEUI = XX XX XX XX XX XX XX XX
292
293 AT+DADDR=XXXXXXXX
294
295 ……….
296
297 AT+RX2WTO=X
298
299 AT+CHS=868100000
300
301 OK
302 )))
303
304
305
306 = 5. Keys, IDs and EUIs management =
307
308 == 5.1 Application EUI ==
309
310 Feature: Get or Set the Application EUI.
311
312 {{info}}
313 **AT Command: AT+APPEUI**
314 {{/info}}
315
316 (% border="1" style="background-color:#ffffcc; color:green; width:686.222px" %)
317 |=(% colspan="3" style="width: 683px;" %)AT+APPEUI
318 |(% style="width:305px" %)**Command Example**|(% style="width:186px" %)**Function**|(% style="width:191px" %)**Response**
319 |(% style="width:305px" %)AT+APPEUI=?|(% style="width:186px" %)Get the Application EUI|(% style="width:191px" %)00 b3 d5 00 00 00 00 00(((
320 OK
321 )))
322 |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
323
324
325
326 == 5.2 Application Key ==
327
328 Feature: Get or Set the Application Key.
329
330 {{info}}
331 **AT Command: AT+APPKEY**
332 {{/info}}
333
334 (% border="1" style="background-color:#ffffcc; color:green; width:976.222px" %)
335 |=(% colspan="3" style="width: 973px;" %)AT+APPKEY
336 |(% style="width:441px" %)**Command Example**|(% style="width:180px" %)**Function**|(% style="width:350px" %)**Response**
337 |(% style="width:441px" %)AT+APPKEY=?|(% style="width:180px" %)Get the Application Key|(% style="width:350px" %)00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35(((
338 OK
339 )))
340 |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
341
342
343 == 5.3 Application Session Key ==
344
345 Feature: Get or Set the Application Session Key.
346
347 {{info}}
348 **AT Command: AT+APPSKEY**
349 {{/info}}
350
351 (% border="1" style="background-color:#ffffcc; color:green; width:1040.22px" %)
352 |=(% colspan="3" style="width: 1037px;" %)AT+APPSKEY
353 |(% style="width:451px" %)**Command Example**|(% style="width:231px" %)**Function**|(% style="width:354px" %)**Response**
354 |(% style="width:451px" %)AT+APPSKEY=?|(% style="width:231px" %)Get the Application Session Key|(% style="width:354px" %)00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2(((
355 OK
356 )))
357 |(% style="width:451px" %)AT+APPSKEY=00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2|(% style="width:231px" %)Set the Application Session Key|(% style="width:354px" %)(While Error in format, return AT_PARAM_ERROR)(((
358 OK
359 )))
360
361
362 == 5.4 Device Address ==
363
364 Feature: Get or Set the Device Address.
365
366 {{info}}
367 **AT Command: AT+DADDR**
368 {{/info}}
369
370 (% border="1" style="background-color:#ffffcc; color:green; width:795.222px" %)
371 |=(% colspan="3" style="width: 792px;" %)AT+DADDR
372 |(% style="width:192px" %)**Command Example**|(% style="width:241px" %)**Function**|(% style="width:359px" %)**Response**
373 |(% style="width:192px" %)AT+DADDR=?|(% style="width:241px" %)Get the Application Session Key.|(% style="width:359px" %)(While Error in format, return AT_PARAM_ERROR)(((
374 A8 40 41 FF
375
376 OK
377 )))
378 |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
379
380
381 == 5.5 Device EUI ==
382
383 Feature: Get or Set the Device EUI.
384
385 {{info}}
386 **AT Command: AT+DEUI**
387 {{/info}}
388
389 (% border="1" style="background-color:#ffffcc; color:green; width:1035.22px" %)
390 |=(% colspan="3" style="width: 1032px;" %)AT+DEUI
391 |(% style="width:250px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:634px" %)**Response**
392 |(% style="width:250px" %)AT+DEUI=?|(% style="width:147px" %)Get the Device EUI.|(% style="width:634px" %)00 44 34 22 33 45 55 55(((
393 OK
394 )))
395 |(% style="width:250px" %)AT+DEUI=A8 40 41 FF FF 12 34 56|(% style="width:147px" %)Set the Device EUI.|(% style="width:634px" %)(System will write new value to Device EUI,While Error in format, return AT_PARAM_ERROR)(((
396 OK
397 )))
398
399
400 == 5.6 Network ID ==
401
402 Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
403
404 {{info}}
405 **AT Command: AT+NWKID**
406 {{/info}}
407
408 (% border="1" style="background-color:#ffffcc; color:green; width:448.222px" %)
409 |=(% colspan="3" style="width: 445px;" %)AT+NWKID
410 |(% style="width:191px" %)**Command Example**|(% style="width:153px" %)**Function**|(% style="width:101px" %)**Response**
411 |(% style="width:191px" %)AT+NWKID=?|(% style="width:153px" %)Get the Network ID.|(% style="width:101px" %)a8 40 41 ff(((
412 OK
413 )))
414 |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
415
416
417 == 5.7 Network Session Key ==
418
419 Feature: Get or Set the Network Session Key
420
421 {{info}}
422 **AT Command: AT+NWKSKEY**
423 {{/info}}
424
425 (% border="1" style="background-color:#ffffcc; color:green; width:1017.22px" %)
426 |=(% colspan="3" style="width: 1014px;" %)AT+NWKSKEY
427 |(% style="width:455px" %)**Command Example**|(% style="width:215px" %)**Function**|(% style="width:343px" %)**Response**
428 |(% style="width:455px" %)AT+NWKSKEY=?|(% style="width:215px" %)Get the Network Session Key.|(% style="width:343px" %)00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92(((
429 OK
430 )))
431 |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
432
433
434 = 6. Joining and sending date on LoRaWAN network =
435
436 == 6.1 Confirm Mode ==
437
438 Feature: Get or Set the confirmation mode (0-1).
439
440 {{info}}
441 **AT Command: AT+CFM**
442 {{/info}}
443
444 (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
445 |=(% colspan="3" style="width: 707px;" %)AT+CFM
446 |(% style="width:155px" %)**Command Example**|(% style="width:205px" %)**Function**|(% style="width:346px" %)**Response**
447 |(% style="width:155px" %)AT+CFM=?|(% style="width:205px" %)Get the confirmation mode|(% style="width:346px" %)0(((
448 OK
449 )))
450 |(% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK
451 |(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
452
453 Downlink Command: 0x05
454
455 Format: Command Code (0x05) followed by 2 bytes mode value.
456
457 If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
458
459 * Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
460 * Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
461
462
463 == 6.2 Confirm Status ==
464
465 Feature: Get confirmation status of the last AT+SEND (0-1).
466
467 {{info}}
468 **AT Command: AT+CFS**
469 {{/info}}
470
471 (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
472 |=(% colspan="3" style="width: 531px;" %)AT+CFS
473 |(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:178px" %)**Response**
474 |(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:178px" %)0(((
475 OK
476 )))
477
478
479 == 6.3 Join LoRa® Network ==
480
481 Feature: Join network.
482
483 {{info}}
484 **AT Command: AT+JOIN**
485 {{/info}}
486
487 (% border="1" style="background-color:#ffffcc; color:green; width:647.222px" %)
488 |=(% colspan="3" style="width: 644px;" %)AT+JOIN
489 |(% style="width:163px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:334px" %)**Response**
490 |(% style="width:163px" %)AT+JOIN ?|(% style="width:147px" %)Get imformation.|(% style="width:334px" %)AT+JOIN: Join network(((
491 OK
492
493 While Error in format, return AT_BUSY_ERROR
494 )))
495
496
497
498 == 6.4 LoRa® Network Join Mode ==
499
500 Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
501
502 {{info}}
503 **AT Command: AT+NJM**
504 {{/info}}
505
506 (% border="1" style="background-color:#ffffcc; color:green; width:753.222px" %)
507 |=(% colspan="3" style="width: 750px;" %)AT+NJM
508 |(% style="width:162px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:361px" %)**Response**
509 |(% style="width:162px" %)AT+NJM=?|(% style="width:227px" %)Get the Network Join Mode|(% style="width:361px" %)1(((
510 OK
511 )))
512 |(% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK
513 |(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
514
515 {{info}}
516 **Downlink Command: 0x20**
517 {{/info}}
518
519 Format: Command Code (0x20) followed by 1 bytes mode value.
520
521 If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
522
523 * **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=O
524 * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
525
526
527
528 == 6.5 LoRa® Network Join Status ==
529
530 Feature: LoRa® Network Join Status.
531
532 {{info}}
533 **AT Command: AT+NJS**
534 {{/info}}
535
536 (% border="1" style="background-color:#ffffcc; color:green; width:498.222px" %)
537 |=(% colspan="3" style="width: 495px;" %)AT+NJS
538 |(% style="width:169px" %)**Command Example**|(% style="width:164px" %)**Function**|(% style="width:161px" %)**Response**
539 |(% style="width:169px" %)AT+NJS=?|(% style="width:164px" %)Get the join status.|(% style="width:161px" %)0(((
540 OK
541 )))
542
543
544
545 == 6.6 Print Last Received Data in Raw Format ==
546
547 Feature: Print Last Received Data in Raw Format<port:data>.
548
549 {{info}}
550 **AT Command: AT+RECV**
551 {{/info}}
552
553 (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
554 |=(% colspan="3" style="width: 584px;" %)AT+RECV
555 |(% style="width:161px" %)**Command Example**|(% style="width:272px" %)**Function**|(% style="width:150px" %)**Response**
556 |(% style="width:161px" %)AT+RECV=?|(% style="width:272px" %)print last received data in raw format.|(% style="width:150px" %)0:(((
557 OK
558 )))
559
560
561
562 == 6.7 Print Last Received Data in Binary Format ==
563
564 Feature: Print Last Received Data in Binary Format<port:data>.
565
566 {{info}}
567 **AT Command: AT+RECVB**
568 {{/info}}
569
570 (% border="1" style="background-color:#ffffcc; color:green; width:793.222px" %)
571 |=(% colspan="3" style="width: 790px;" %)AT+RECVB
572 |(% style="width:173px" %)**Command Example**|(% style="width:497px" %)**Function**|(% style="width:120px" %)**Response**
573 |(% style="width:173px" %)AT+RECVB=?|(% style="width:497px" %)print last received data in binary format (with hexadecimal values).|(% style="width:120px" %)2: 0010(((
574 OK
575 )))
576
577
578
579 == 6.8 Send Text Data ==
580
581 Feature: Send Text Data<port:data>.
582
583 {{info}}
584 **AT Command: AT+SEND**
585 {{/info}}
586
587 (% border="1" style="background-color:#ffffcc; color:green; width:991.222px" %)
588 |=(% colspan="3" style="width: 988px;" %)AT+SEND
589 |(% style="width:201px" %)**Command Example**|(% style="width:340px" %)**Function**|(% style="width:446px" %)**Response**
590 |(% style="width:201px" %)AT+SEND=12:hello world|(% style="width:340px" %)Send text data along with the application port.|(% style="width:446px" %)OK(((
591 While Error in format, return
592
593 AT_BUSY_ERROR/AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
594
595
596 )))
597
598 == 6.9 Send Hexadecimal Data ==
599
600 Feature: Send hexadecimal data along with the application port.
601
602 {{info}}
603 **AT Command: AT+SENDB**
604 {{/info}}
605
606 (% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
607 |=(% colspan="3" style="width: 1117px;" %)AT+SENDB
608 |(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
609 |(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK
610 |(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)While Error in format, return(((
611 AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
612
613
614 )))
615
616 = 7. LoRaWAN network management =
617
618 == 7.1 Adaptive Data Rate ==
619
620 Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on).
621
622 {{info}}
623 **AT Command: AT+ADR**
624 {{/info}}
625
626 (% border="1" style="background-color:#ffffcc; color:green; width:683.222px" %)
627 |=(% colspan="3" style="width: 680px;" %)AT+ADR
628 |(% style="width:162px" %)**Command Example**|(% style="width:266px" %)**Function**|(% style="width:250px" %)**Response**
629 |(% style="width:162px" %)AT+ADR=?|(% style="width:266px" %)Get the Adaptive Data Rate setting.|(% style="width:250px" %)1(((
630 OK
631 )))
632 |(% style="width:162px" %)AT+ADR=0|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)OK
633 |(% style="width:162px" %)AT+ADR=2|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)While Error in format, return(((
634 AT_PARAM_ERROR
635 )))
636
637 {{info}}
638 **Downlink Command: 0x22**
639 {{/info}}
640
641
642 If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
643
644 * **Example 1**: Downlink Payload: **2201** ~/~/ Set AT+ADR=1.
645 * **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
646
647 == 7.2 LoRa® Class ==
648
649 Feature: Get or Set the Device Class(Currently only support class A, class C).
650
651 {{info}}
652 **AT Command:AT+CLASS**
653 {{/info}}
654
655 (% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
656 |=(% colspan="3" style="width: 504px;" %)AT+CLASS
657 |(% style="width:163px" %)**Command Example**|(% style="width:166px" %)**Function**|(% style="width:175px" %)**Response**
658 |(% style="width:163px" %)AT+CLASS=?|(% style="width:166px" %)Get the Device Class.|(% style="width:175px" %)A(((
659 OK
660 )))
661 |(% style="width:163px" %)AT+CLASS=C|(% style="width:166px" %)Set the Device Class.|(% style="width:175px" %)OK(((
662
663 )))
664
665 == 7.3 Duty Cycle Setting ==
666
667 Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
668
669 {{info}}
670 **AT Command:AT+DCS**
671 {{/info}}
672
673 (% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
674 |=(% colspan="3" style="width: 512px;" %)AT+DCS
675 |(% style="width:165px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:107px" %)**Response**
676 |(% style="width:165px" %)AT+DCS=?|(% style="width:239px" %)Get the ETSI Duty Cycle setting.|(% style="width:107px" %)1(((
677 OK
678 )))
679 |(% style="width:165px" %)AT+DCS=1|(% style="width:239px" %)Set the ETSI Duty Cycle setting.|(% style="width:107px" %)OK(((
680
681 )))
682
683 == 7.4 Data Rate ==
684
685 Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
686
687 {{info}}
688 **AT Command: AT+DR**
689 {{/info}}
690
691 (% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
692 |=(% colspan="3" style="width: 463px;" %)AT+DR
693 |(% style="width:156px" %)**Command Example**|(% style="width:167px" %)**Function**|(% style="width:140px" %)**Response**
694 |(% style="width:156px" %)AT+DR=?|(% style="width:167px" %)Get the Data Rate.|(% style="width:140px" %)5(((
695 OK
696 )))
697 |(% style="width:156px" %)AT+DR=2|(% style="width:167px" %)Set the Data Rate.|(% style="width:140px" %)OK(((
698
699 )))
700
701 {{info}}
702 **Downlink Command: 0x2200aaFF**
703 {{/info}}
704
705
706 If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
707
708 * **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
709 * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
710
711 == 7.5 Frame Counter Downlink ==
712
713 Feature: Get or Set the Frame Counter Downlink.
714
715 {{info}}
716 **AT Command:AT+FCD**
717 {{/info}}
718
719 (% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
720 |=(% colspan="3" style="width: 690px;" %)AT+FCD
721 |(% style="width:162px" %)**Command Example**|(% style="width:258px" %)**Function**|(% style="width:269px" %)**Response**
722 |(% style="width:162px" %)AT+FCD=?|(% style="width:258px" %)Get the Frame Counter Downlink.|(% style="width:269px" %)0(((
723 OK
724 )))
725 |(% style="width:162px" %)AT+FCD=10|(% style="width:258px" %)Set the Frame Counter Downlink.|(% style="width:269px" %)(System will write new value to FCD)(((
726 OK
727
728
729 )))
730
731 == 7.6 Frame Counter Uplink ==
732
733 Feature: Get or Set the Frame Counter Uplink.
734
735 {{info}}
736 **AT Command:AT+FCU**
737 {{/info}}
738
739 (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
740 |=(% colspan="3" style="width: 531px;" %)AT+FCU
741 |(% style="width:177px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:113px" %)**Response**
742 |(% style="width:177px" %)AT+FCU=?|(% style="width:239px" %)Get the Frame Counter Uplink.|(% style="width:113px" %)0(((
743 OK
744 )))
745 |(% style="width:177px" %)AT+FCU=10|(% style="width:239px" %)Set the Frame Counter Uplink.|(% style="width:113px" %)OK(((
746
747 )))
748
749 == 7.7 Join Accept Delay1 ==
750
751 Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
752
753 {{info}}
754 **AT Command:AT+JN1DL**
755 {{/info}}
756
757 (% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
758 |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
759 |(% style="width:164px" %)**Command Example**|(% style="width:229px" %)**Function**|(% style="width:140px" %)**Response**
760 |(% style="width:164px" %)AT+JN1DL=?|(% style="width:229px" %)Get the Join Accept Delay.|(% style="width:140px" %)5000(((
761 OK
762 )))
763 |(% style="width:164px" %)AT+JN1DL=10000|(% style="width:229px" %)Set the Join Accept Delay.|(% style="width:140px" %)OK(((
764
765 )))
766
767 == 7.8 Join Accept Delay2 ==
768
769 Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
770
771 {{info}}
772 **AT Command:AT+JN2DL**
773 {{/info}}
774
775 (% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
776 |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
777 |(% style="width:160px" %)**Command Example**|(% style="width:228px" %)**Function**|(% style="width:146px" %)**Response**
778 |(% style="width:160px" %)AT+JN2DL=?|(% style="width:228px" %)Get the Join Accept Delay.|(% style="width:146px" %)6000(((
779 OK
780 )))
781 |(% style="width:160px" %)AT+JN2DL=20000|(% style="width:228px" %)Set the Join Accept Delay.|(% style="width:146px" %)OK(((
782
783 )))
784
785 == 7.9 Public Network Mode ==
786
787 Feature: Get or Set the public network mode. (0: off, 1: on)
788
789 {{info}}
790 **AT Command:AT+PNM**
791 {{/info}}
792
793 (% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
794 |=(% colspan="3" style="width: 664px;" %)AT+PNM
795 |(% style="width:166px" %)**Command Example**|(% style="width:225px" %)**Function**|(% style="width:272px" %)**Response**
796 |(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
797 OK
798 )))
799 |(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)Set the public network mode.|(% style="width:272px" %)(System will write new value to PNM)(((
800 OK
801
802
803 )))
804
805 == 7.10 Receive Delay1 ==
806
807 Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
808
809 {{info}}
810 **AT Command:AT+RX1DL**
811 {{/info}}
812
813 (% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
814 |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
815 |(% style="width:155px" %)**Command Example**|(% style="width:128px" %)**Function**|(% style="width:122px" %)**Response**
816 |(% style="width:155px" %)AT+RX1DL=?|(% style="width:128px" %)Get the delay.|(% style="width:122px" %)1000(((
817 OK
818 )))
819 |(% style="width:155px" %)AT+RX1DL=1500|(% style="width:128px" %)Set the delay.|(% style="width:122px" %)OK(((
820
821 )))
822
823 == 7.11 Receive Delay2 ==
824
825 Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
826
827 {{info}}
828 **AT Command:AT+RX2DL**
829 {{/info}}
830
831 (% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
832 |=(% colspan="3" style="width: 478px;" %)AT+RX2DL
833 |(% style="width:175px" %)**Command Example**|(% style="width:152px" %)**Function**|(% style="width:150px" %)**Response**
834 |(% style="width:175px" %)AT+RX2DL=?|(% style="width:152px" %)Get the delay.|(% style="width:150px" %)2000(((
835 OK
836 )))
837 |(% style="width:175px" %)AT+RX2DL=2500|(% style="width:152px" %)Set the delay.|(% style="width:150px" %)OK(((
838
839 )))
840
841 == 7.12 Rx2 Window Data Rate ==
842
843 Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
844
845 {{info}}
846 **AT Command:AT+RX2DR**
847 {{/info}}
848
849 (% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
850 |=(% colspan="3" style="width: 522px;" %)AT+RX2DR
851 |(% style="width:160px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:130px" %)**Response**
852 |(% style="width:160px" %)AT+RX2DR=?|(% style="width:232px" %)Get the Rx2 window data rate.|(% style="width:130px" %)2(((
853 OK
854 )))
855 |(% style="width:160px" %)AT+RX2DR=6|(% style="width:232px" %)Set the Rx2 window data rate.|(% style="width:130px" %)OK(((
856
857 )))
858
859 == 7.13 Rx2 Window Frequency ==
860
861 Feature: Get or Set the Rx2 window frequency
862
863 {{info}}
864 **AT Command:AT+RX2FQ**
865 {{/info}}
866
867 (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
868 |=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
869 |(% style="width:183px" %)**Command Example**|(% style="width:240px" %)**Function**|(% style="width:160px" %)**Response**
870 |(% style="width:183px" %)AT+RX2FQ=?|(% style="width:240px" %)Get the Rx2 window frequency.|(% style="width:160px" %)434665000(((
871 OK
872 )))
873 |(% style="width:183px" %)AT+RX2FQ=434665000|(% style="width:240px" %)Set the Rx2 window frequency.|(% style="width:160px" %)OK(((
874
875 )))
876
877 == 7.14 Transmit Power ==
878
879 Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
880
881 {{info}}
882 **AT Command:AT+TXP**
883 {{/info}}
884
885 (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
886 |=(% colspan="3" style="width: 462px;" %)AT+TXP
887 |(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
888 |(% style="width:161px" %)AT+TXP=?|(% style="width:189px" %)Get the Transmit Power.|(% style="width:112px" %)0(((
889 OK
890 )))
891 |(% style="width:161px" %)AT+TXP=1|(% style="width:189px" %)Set the Transmit Power.|(% style="width:112px" %)OK(((
892
893 )))
894
895 Downlink Payload. The 4th byte of 0x22 downlink.
896
897 If the downlink payload=22000100, it means setting the TXP to 0.
898
899 * **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
900 * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
901
902 == 7.15 RSSI of the Last Received Packet ==
903
904 Feature: Get or Set the Rx2 window frequency
905
906 {{info}}
907 **AT Command:AT+RSSI**
908 {{/info}}
909
910 (% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %)
911 |=(% colspan="3" style="width: 554px;" %)AT+RSSI
912 |(% style="width:164px" %)**Command Example**|(% style="width:289px" %)**Function**|(% style="width:100px" %)**Response**
913 |(% style="width:164px" %)AT+RSSI=?|(% style="width:289px" %)Get the RSSI of the last received packet.|(% style="width:100px" %)0(((
914 OK
915 )))
916
917 == 7.16 SNR of the Last Received Packet ==
918
919 Feature: Get the SNR of the last received packet
920
921 {{info}}
922 **AT Command:AT+SNR**
923 {{/info}}
924
925 (% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
926 |=(% colspan="3" style="width: 568px;" %)AT+SNR
927 |(% style="width:164px" %)**Command Example**|(% style="width:290px" %)**Function**|(% style="width:113px" %)**Response**
928 |(% style="width:164px" %)AT+SNR=?|(% style="width:290px" %)Get the RSSI of the last received packet.|(% style="width:113px" %)0(((
929 OK
930 )))
931
932 == 7.17 Application Port ==
933
934 Feature: Get or set the application port.
935
936 {{info}}
937 **AT Command: AT+PORT**
938 {{/info}}
939
940 (% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %)
941 |=(% colspan="3" style="width: 497px;" %)AT+PORT
942 |(% style="width:157px" %)**Command Example**|(% style="width:204px" %)**Function**|(% style="width:135px" %)**Response**
943 |(% style="width:157px" %)AT+PORT=?|(% style="width:204px" %)Get the application port|(% style="width:135px" %)21(((
944 OK
945 )))
946 |(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
947
948 {{info}}
949 **Downlink Command: 0x23**
950 {{/info}}
951
952 Format: Command Code (0x23) followed by 1 bytes port value.
953
954 If the downlink payload=2301, it means set the application port to 1, while type code is 23.
955
956 * **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
957 * **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
958
959 == 7.18 Single Channel Mode ==
960
961 Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
962
963 {{info}}
964 **AT Command: AT+CHS**
965 {{/info}}
966
967 (% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %)
968 |=(% colspan="3" style="width: 600px;" %)AT+CHS
969 |(% style="width:182px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:122px" %)**Response**
970 |(% style="width:182px" %)AT+CHS=?|(% style="width:295px" %)Get Frequency for Single Channel Mode|(% style="width:122px" %)0(((
971 OK
972 )))
973 |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
974
975 == 7.19 Eight Channel Mode ==
976
977 Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
978
979 {{info}}
980 **AT Command: AT+CHE**
981 {{/info}}
982
983 (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
984 |=(% colspan="3" style="width: 707px;" %)AT+CHE
985 |(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
986 |(% style="width:160px" %)AT+CHE=?|(% style="width:198px" %)Get eight channels mode|(% style="width:349px" %)1(((
987 902.3 902.5 902.7 902.9 903.1 903.3 903.5 903.7
988
989 OK
990 )))
991 |(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
992
993 {{info}}
994 **Downlink Command: 0x24**
995 {{/info}}
996
997 Format: Command Code (0x24) followed by 1 bytes channel value.
998
999 If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1000
1001 * **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
1002 * **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1003
1004 == 7.20 Get or Set RXwindows1 timeout ==
1005
1006 Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1007
1008 {{info}}
1009 **AT Command: AT+RX1WTO**
1010 {{/info}}
1011
1012 (% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %)
1013 |=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO
1014 |(% style="width:163px" %)**Command Example**|(% style="width:201px" %)**Function**|(% style="width:93px" %)**Response**
1015 |(% style="width:163px" %)AT+RX1WTO=?|(% style="width:201px" %)Get RXwindows1 timeout|(% style="width:93px" %)14(((
1016 OK
1017 )))
1018 |(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK
1019
1020 (((
1021 **AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1022 )))
1023
1024 [[image:image-20220526162535-1.png]]
1025
1026 (((
1027 Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1028
1029
1030 )))
1031
1032 == 7.21 Get or Set RXwindows2 timeout ==
1033
1034 Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1035
1036 {{info}}
1037 **AT Command: AT+RX2WTO**
1038 {{/info}}
1039
1040 (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1041 |=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO
1042 |(% style="width:190px" %)**Command Example**|(% style="width:199px" %)**Function**|(% style="width:104px" %)**Response**
1043 |(% style="width:190px" %)AT+RX2WTO=?|(% style="width:199px" %)Get RXwindows2 timeout|(% style="width:104px" %)7(((
1044 OK
1045 )))
1046 |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1047
1048 == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1049
1050 Feature: Get or Set uplinkdwelltime
1051
1052 {{info}}
1053 **AT Command: AT+DWELLT**
1054 {{/info}}
1055
1056 (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1057 |=(% colspan="3" style="width: 494px;" %)AT+DWELLT
1058 |(% style="width:183px" %)**Command Example**|(% style="width:179px" %)**Function**|(% style="width:131px" %)**Response**
1059 |(% style="width:183px" %)AT+DWELLT=?|(% style="width:179px" %)Get uplinkdwelltime|(% style="width:131px" %)1(((
1060 OK
1061 )))
1062 |(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
1063
1064 {{info}}
1065 **Downlink Command: 0x25**
1066 {{/info}}
1067
1068 Format: Command Code (0x25) followed by 1 bytes state value.
1069
1070 If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1071
1072 * **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1073 * **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1074
1075 == 7.23 Set Packet Receiving Response Level ==
1076
1077 Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1078
1079 RPL value:
1080
1081 * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1082 * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
1083 * **AT+RPL=2:** Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
1084 * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1085 * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1086
1087 Case Analyes:
1088
1089 * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1090 * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1091 * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1092
1093 {{info}}
1094 **AT Command: AT+RPL**
1095 {{/info}}
1096
1097 (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1098 |=(% colspan="3" style="width: 533px;" %)AT+RPL
1099 |(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1100 |(% style="width:160px" %)AT+RPL=?|(% style="width:263px" %)Get packet receiving response level|(% style="width:109px" %)1(((
1101 OK
1102 )))
1103 |(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
1104
1105 {{info}}
1106 **Downlink Command: 0x21**
1107 {{/info}}
1108
1109 Format: Command Code (0x21) followed by 1 bytes level value.
1110
1111 If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1112
1113 * **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1114 * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1115
1116 = 8. AT Commands Combination =
1117
1118 == 8.1 Set a fix RX2DR for downlink window ==
1119
1120 * **AT+ADR=0 **~-~-> Disable ADR first
1121 * **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1122
1123 == 8.2 Use Downlink Command to set a fix uplink DR ==
1124
1125 {{info}}
1126 **Downlink Command: 0x22000500**
1127 {{/info}}
1128
1129 Same as:
1130
1131 * AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1132 * AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1133 * AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]