Wiki source code of Connection to Senra
Hide last authors
| author | version | line-number | content |
|---|---|---|---|
 |
1.2 | 1 | Contents: |
| |
1.1 | 2 | |
| 3 | |||
| |
1.2 | 4 | = 1. Introduction = |
| |
1.1 | 5 | |
| |
1.2 | 6 | Here list some notice when connect to Senra. |
| |
1.1 | 7 | |
| 8 | |||
| |
1.2 | 9 | = 2. Notice for Gateway = |
| |
1.1 | 10 | |
| |
1.2 | 11 | ((( |
| 12 | After register an account in Senra, ask their support to approval your gateway: refer ths link [[https:~~/~~/docs.senraco.io/dev/gw/SemtechPacketForwarder/>>url:https://docs.senraco.io/dev/gw/SemtechPacketForwarder/]] for gateway instruction of Senra. | ||
| 13 | ))) | ||
| |
1.1 | 14 | |
| |
1.2 | 15 | [[image:https://wiki.dragino.com/images/thumb/e/e7/Senra-1.png/600px-Senra-1.png||height="376" width="600"]] |
| |
1.1 | 16 | |
| |
1.2 | 17 | Gateway Must be Approval |
| |
1.1 | 18 | |
| |
1.2 | 19 | * The Gateway EUI must match the Approval Gateway EUI in above screen shot |
| 20 | * The keep alive status set to 300 seconds. Default 30 seconds is too short to Senra | ||
| |
1.1 | 21 | |
| |
1.2 | 22 | [[image:https://wiki.dragino.com/images/thumb/6/69/Senra-2.png/600px-Senra-2.png||height="533" width="600"]] |
| |
1.1 | 23 | |
| |
1.2 | 24 | Configure the Gateway with correct settings. |
| |
1.1 | 25 | |
| |
1.2 | 26 | Gateway should be Active after have internet connection. like below: |
| |
1.1 | 27 | |
| |
1.2 | 28 | [[image:https://wiki.dragino.com/images/thumb/a/ab/Senra-gw_3.png/600px-Senra-gw_3.png||height="177" width="600"]] |
| |
1.1 | 29 | |
| |
1.2 | 30 | Configure the Gateway with correct settings. |
| |
1.1 | 31 | |
| |
1.2 | 32 | = 3. Notice for End node = |
| 33 | |||
| 34 | == 3.1 Set up for OTAA mode == | ||
| 35 | |||
| 36 | == 3.2 Set up for ABP Mode == | ||
| 37 | |||
| 38 | ((( | ||
| 39 | ABP Mode devices has to be IN868 frequency band as well, User can use ABP mode to update data. | ||
| 40 | ))) | ||
| 41 | |||
| 42 | ((( | ||
| 43 | For Dragino End Node, user can access to the device console and run AT Command "**AT+NJM=0**" to set it to ABP mode. | ||
| 44 | ))) | ||
| 45 | |||
| 46 | ((( | ||
| 47 | User can know the keys by run **AT+CFG**. | ||
| 48 | ))) | ||
| 49 | |||
| 50 | [[image:https://wiki.dragino.com/images/thumb/8/87/Senra-EndNode-1.png/600px-Senra-EndNode-1.png||height="116" width="600"]] | ||
| 51 | |||
| 52 | AT+CFG command output from End node | ||
| 53 | |||
| 54 | In Senra, need to create a ABP device | ||
| 55 | |||
| 56 | [[image:https://wiki.dragino.com/images/thumb/7/73/Senra-EndNode-2.png/600px-Senra-EndNode-2.png||height="446" width="600"]] | ||
| 57 | |||
| 58 | Create ABP Device | ||
| 59 | |||
| 60 | And input the keys: | ||
| 61 | |||
| 62 | * Device EUI : Use the value from AT+DEUI | ||
| 63 | * Device ADDR: Use the value from AT+DADDR | ||
| 64 | * Application session key: Use the value from AT+APPSKEY | ||
| 65 | * Network Session Key: Use the value from AT+NWKSKEY | ||
| 66 | |||
| 67 | [[image:https://wiki.dragino.com/images/8/8d/Senra-EndNode-3.png||height="484" width="593"]] | ||
| 68 | |||
| 69 | Create ABP Device | ||
| 70 | |||
| 71 | After Successfule uplink, User will be to see the activity: | ||
| 72 | |||
| 73 | [[image:https://wiki.dragino.com/images/thumb/3/30/Senra-EndNode-4.png/600px-Senra-EndNode-4.png||height="166" width="600"]] | ||
| 74 | |||
| 75 | ABP Device Info |