Changes for page Application Note : Communicate with Different Sensors ----- RS485-LN / RS485-BL

Last modified by Karry Zhuang on 2024/07/11 11:58

From version < 1.13 >

edited by Xiaoling
on 2022/05/12 10:15

To version < 1.10 >

edited by Xiaoling
on 2022/05/12 10:05

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -20,6 +20,7 @@
  * [[Configure Manual>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/Application_Note/Relay_VFD/]] : Explanation on how to integrate to Node-red and to the Mobile Phone, and with link to the Github code.
  * [[Video Demo>>url:https://www.youtube.com/watch?v=TAFZ5eaf-MY&t=6s&ab_channel=XavierFlorensaBerenguer]]
++
  == 1.2 Example 2: Connect to Pulse Counter ==
  This instruction is provided by Xavier Florensa Berenguer from [[NORIA GRUPO DE COMPRAS>>url:http://www.gruponovelec.com/]]. It is to show how to use RS485-LN to connect to Pulse Counter and communicate with Mobile. This example and example 2 compose the structure for a farm IoT solution. The structure is like below:
@@ -35,6 +35,7 @@
  * [[Pickdata MIO40 water pulse counter to LoRa with Dragino RS485-LN>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/Application_Note/Pulse-Counter/]] : Configure Document
  * [[Dragino Solution in Farm>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/Application_Note/&file=Dragino%20on%20Farms.pptx]]
++
  == 1.3 Example3: Use RS485-LN with energy meters ==
  === 1.3.1 OverView ===
@@ -47,7 +47,7 @@
  This example describes a single-phase meter.This is the connection between the RS485-LN and the energy meter.
  )))
--[[image:https://wiki.dragino.com/images/thumb/f/f4/Meter1.jpg/600px-Meter1.jpg||height="726" width="545"]]
++[[image:https://wiki.dragino.com/images/thumb/f/f4/Meter1.jpg/600px-Meter1.jpg||height="800" width="600"]]
  Connection1
@@ -63,13 +63,12 @@
  Once there is power, the RS485-LN will be on.
--[[image:https://wiki.dragino.com/images/thumb/1/15/Meter2.jpg/600px-Meter2.jpg||height="433" width="577"]]
++[[image:https://wiki.dragino.com/images/thumb/1/15/Meter2.jpg/600px-Meter2.jpg||height="450" width="600"]]
  Connection2
++[[image:https://wiki.dragino.com/images/thumb/a/a5/Meter3.jpg/600px-Meter3.jpg||height="800" width="600"]]
--[[image:https://wiki.dragino.com/images/thumb/a/a5/Meter3.jpg/600px-Meter3.jpg||height="763" width="573"]]
--
  Connection3
@@ -90,9 +90,7 @@
  * 5th and 6th bytes: Number of registers to read
  * 7th and 8th bytes: CRC16 checksum from bytes 1 to 6.
--(((
  How to parse the reading of the return command of the parameter：
--)))
  (% class="box infomessage" %)
  (((
@@ -106,6 +106,7 @@
  * The 6th and 7th bytes: CRC16 checksum
  * 08 FD is register data. Use short integer 16 bits to convert to decimal, get 2301, then 230.1V is the voltage.
++
  === 1.3.3 How to configure RS485-LN and parse output commands ===
  RS485-LN provides two configuration methods: AT COMMAND and DOWNLINK.
@@ -120,7 +120,7 @@
  [[image:https://wiki.dragino.com/images/b/bc/AT_COMMAND1.png||height="358" width="456"]]
--AT COMMAND
++**AT COMMAND**
  (% class="box infomessage" %)
  (((
@@ -149,53 +149,27 @@
  [[image:https://wiki.dragino.com/images/thumb/c/c2/AT_COMMAND3.png/600px-AT_COMMAND3.png||height="138" width="600"]]
--(((
  AT COMMAND
--)))
--(((
--
--)))
--
--(((
  **Example**: CMD1:Read current data with MODBUS command. address:0x03 AT+COMMAND1= 01 03 00 03 00 01,1
--)))
--(((
  RETURN1:01 03 02 00 02 39 85 00 00(return data)
--)))
--(((
  AT+DATACUT1:9,1,4+5+6+7 Take the return value 00 02 39 85 as the valid value of reading current data and used to splice payload.
--)))
--(((
  CMD2:Read voltage data with MODBUS command. address:0x00 AT+COMMAND2= 01 03 00 00 00 01,1
--)))
--(((
  RETURN2:01 03 02 08 DC BE 1D(return data)
--)))
--(((
  AT+DATACUT2:7,1,4+5 Take the return value 08 DC as the valid value of reading voltage data and used to splice payload.
--)))
--(((
  CMD3:Read total active energy data with MODBUS command. address:0x0031 AT+COMMAND3= 01 03 00 31 00 02,1
--)))
--(((
  RETURN3:01 03 04 00 00 00 44 FA 00(return data)
--)))
--(((
  AT+DATACUT3:9,1,4+5+6+7 Take the return value 00 00 00 44 as the valid value of reading total active energy data and used to splice payload.
--)))
--(((
  Payload:01 00 02 39 85 08 DC 00 00 00 44
--)))
  [[image:https://wiki.dragino.com/images/thumb/9/9b/AT_COMMAND10.png/600px-AT_COMMAND10.png||height="278" width="600"]]
@@ -299,47 +299,30 @@
  === 1.3.4 How to configure and output commands for RS485 to USB ===
--(((
  This step is not necessary, it is just to show how to use a normal RS485 to USB adapter to connect to the meter to check the input and output. This can be used to test the connection and RS485 command of the meter without RS485-LN.
--)))
--(((
  First, connect the A+ and A- of the USB to the 485 A and 485 B of the energy meter.
--)))
--(((
  Open the serial port debugging, set the send and receive to HEX.
--)))
--(((
  Baud rate: 9600
--)))
--(((
  check digit: Even
--)))
  [[image:https://wiki.dragino.com/images/thumb/8/8f/Usb_meter2.jpg/600px-Usb_meter2.jpg||height="800" width="600"]]
  USB
--
  [[image:https://wiki.dragino.com/images/thumb/6/62/Usb_meter1.jpg/600px-Usb_meter1.jpg||height="800" width="600"]]
  USB
--
--(((
  The configuration command is consistent with the AT command, input the hexadecimal command directly into the serial port, and the serial port will output the command.
--)))
--(((
--**Example:**  input：01 03 00 31 00 02 95 c4
--)))
++Example:input：01 03 00 31 00 02 95 c4
--(((
--                 output:01 03 04 00 00 00 42 7A 02
--)))
++{{{      output:01 03 04 00 00 00 42 7A 02
++}}}
  [[image:https://wiki.dragino.com/images/thumb/b/b3/Usb_meter3.jpg/600px-Usb_meter3.jpg||height="466" width="600"]]
@@ -398,6 +398,7 @@
  * 08 DF is the valid value of the meter with device address 02.
  * 43 62 is the valid value of the meter with device address 01.
++
  == 1.4 Example 4: Circuit Breaker Remote Open Close ==
  This instruction is provided by Xavier Florensa Berenguer from [[NORIA GRUPO DE COMPRAS>>url:http://www.gruponovelec.com/]]. It is to show how to use RS485-LN to connect to SCHNEIDER SMART and Monitor and control your cabinet remotely with no wires and with Dragino RS485-LN LoRaWAN technology. The structure is like below:
@@ -408,6 +408,7 @@
  * [[Circuit Breaker Remote Open Close>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/Application_Note/Circuit_Breaker_Remote_Open_Close/]] : Configure Documen
++
  == 1.5 Example 5: SEM Three Energy Meter with RS485-BL or RS485-LN ==
  This instruction is provided by Xavier Florensa Berenguer from [[NORIA GRUPO DE COMPRAS>>url:http://www.gruponovelec.com/]]. It is to show how to use RS485-BL to connect to SEM Three Energy Meter and send the data to mobile phone for remote minitor. The structure is like below:
@@ -416,6 +416,7 @@
  * [[Connect to SEM Three>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/Application_Note/SEM_Three_Energy_Meter/&file=SEM%20three%20and%20Dragino%20RS485-LN%20v1.pdf]] : Configure Document for RS485-LN
++
  == 1.6 Example 6:CEM C31 485-T1-MID Energy Meter with RS485-LN ==
  This instruction is provided by Xavier Florensa Berenguer from [[NORIA GRUPO DE COMPRAS>>url:http://www.gruponovelec.com/]]. It is to show how to use RS485-LN to connect to CEM C31 485-T1-MID and send the data for remote minitor. The structure is like below:
@@ -422,6 +422,7 @@
  * [[CEM C31 485-T1-MID>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/Application_Note/ELECTRICAL%20CABINET/&file=ELECTRICAL%20CABINET%20READINGS.pdf]] : Configure Document For RS485-LN
++
  == 1.7 Example 7:Schneider Electric PLC M221 with RS485-BL ==
  [[image:https://wiki.dragino.com/images/thumb/9/97/PLC_M221.png/600px-PLC_M221.png||height="353" width="600"]]

Changes for page Application Note : Communicate with Different Sensors ----- RS485-LN / RS485-BL

Summary

Details

Applications

Navigation