Last modified by Edwin Chen on 2022/11/22 09:38
<
From version < 8.9 >
edited by Xiaoling
on 2022/06/02 14:23
To version < 6.1 >
edited by Xiaoling
on 2022/06/02 11:36
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -17,15 +17,13 @@
17 17  = **2. Features for this firmware** =
18 18  
19 19  
20 -== **2.1  Point To Point** ==
20 +== **2.1  Overview** ==
21 21  
22 +[[image:image-20220602111219-1.png]]
22 22  
23 -[[image:image-20220602111219-1.png||height="472" width="972"]]
24 24  
25 +== **2.2. Configure** ==
25 25  
26 -(% class="wikigeneratedid" id="H2.2.Configure" %)
27 -(% style="color:blue" %)**Configure:**
28 -
29 29  (% border="1" style="background-color:#f7faff; color:black; width:500px" %)
30 30  |=**A's configuration**|=**B's configuration**
31 31  |AT+GROUPMOD=0|AT+GROUPMOD=0
... ... @@ -38,171 +38,13 @@
38 38  |AT+DI2TODO2=2 |AT+DI2TODO2=2
39 39  |AT+DI2TORO2=2|AT+DI2TORO2=2
40 40  
39 +== **2.3.  Serial port display** ==
41 41  
42 -== **2.2  Point To Mult-Point ** ==
43 -
44 -
45 45  [[image:image-20220602111219-2.png]]
46 46  
47 47  
48 48  [[image:image-20220602111219-3.png]]
49 49  
50 -(((
51 51  If the sender does not get the ACK reply from the receiver, it will retransmit up to 4 times, each interval is 6 seconds, and the UplinkCounter of the retransmission will not increase.
52 -)))
53 53  
54 -
55 -== **2.3 AT command** ==
56 -
57 -
58 -(% style="color:#037691" %)**ATZ** (%%)**: ** Trig a reset of the MCU
59 -
60 -(% style="color:#037691" %)**AT+FDR** (%%)**:**  Reset Parameters to Factory Default, Keys Reserve
61 -
62 -(% style="color:#037691" %)**AT+FCU** (%%)**:**  Get or Set the Frame Counter Uplink
63 -
64 -(% style="color:#037691" %)**AT+FCD** (%%)**:**  Get or Set the Frame Counter Downlink
65 -
66 -(% style="color:#037691" %)**AT+TXP** (%%)**:**  Get or Set the transmit power, the maximum is 20dBm (default is 14dBm)
67 -
68 -(% style="color:#037691" %)**AT+SYNC** (%%)**:**  Get or Set the Sync word [1:0x34,0:0x12] (default is 1)
69 -
70 -(% style="color:#037691" %)**AT+PMB** (%%)**:    **Get or Set the preamble (default:8)
71 -
72 -(% style="color:#037691" %)**AT+TXCHS **(%%)**:** Get or Set the transmit frequency of TX (default:868700000)
73 -
74 -(% style="color:#037691" %)**AT+TXSF **(%%)**:**  Get or Set the spreading factor of TX (7 to 12) (default:12)
75 -
76 -(% style="color:#037691" %)**AT+RXCHS **(%%)**:** Get or Set the transmit frequency of RX (default:869000000)
77 -
78 -(% style="color:#037691" %)**AT+RXSF **(%%)**:**  Get or Set the spreading factor of RX (7 to 12) (default:12)
79 -
80 -(% style="color:#037691" %)**AT+BW **(%%)**:  **Get or Set the bandwidth [0:125khz,1:250khz,2:500khz] (default:0)
81 -
82 -(% style="color:#037691" %)**AT+CR **(%%)**:        **Get or Set the coding rate [1: 4/5, 2: 4/6, 3: 4/7, 4: 4/8] (default:1)
83 -
84 -(% style="color:#037691" %)**AT+TDC **(%%)**:**  Get or set the application data transmission interval in ms(default 10 minutes)
85 -
86 -(% style="color:#037691" %)**AT+VER **(%%)**:**  Get firmware version number
87 -
88 -(% style="color:#037691" %)**AT+SEND **(%%)**:  **Set Custom sent hex data
89 -
90 -(% style="color:#037691" %)**AT+GROUPMOD **(%%)**: **Set or Get the grouping mode of the device (default: 0)
91 -
92 -(% style="color:#037691" %)**AT+GROUPID **(%%)**:      **Set or Get the password for matching between TX group and RX group, which can be composed of numbers or characters (default: 12345678)
93 -
94 -(% style="color:#037691" %)**AT+TRIG1 **(%%)**:**  Set or Get the DI1 pin interrupt trigger mode (default 0,0)
95 -
96 -(% style="color:#037691" %)**AT+TRIG2 **(%%)**:            **Set or Get the DI2 pin interrupt trigger mode (default 0,0)
97 -
98 -(% style="color:#037691" %)**AT+DI1TODO1 **(%%)**:    **Set or get the mode in which DI1 maps to DO1 (default 0)
99 -
100 -(% style="color:#037691" %)**AT+DI1TORO1 **(%%)**:    **Set or get the mode in which DI1 maps to RO1(default 0)
101 -
102 -(% style="color:#037691" %)**AT+DI2TODO2 **(%%)**:**  Set or get the mode in which DI2 maps to DO2(default 0)
103 -
104 -(% style="color:#037691" %)**AT+DI2TORO2 **(%%)**:    **Set or get the mode in which DI2 maps to RO2(default 0)
105 -
106 -
107 -
108 -(% style="color:#4f81bd" %)**Example 1:**
109 -
110 -**AT+SEND=01020304 **will send a payload of 01020304
111 -
112 -
113 -(% style="color:#4f81bd" %)**Example 2: **
114 -
115 -**AT+TRIGx=a    **Trigger directly without triggering time
116 -
117 -**AT+TRIGx=a,b**
118 -
119 -a=0: falling edge;
120 -
121 -a=1: rising edge;
122 -
123 -a=2: falling edge or rising edge;
124 -
125 -b:  triggering time in milliseconds.
126 -
127 -AT+TRIGx=2,50  Falling edge or rising edge trigger, and the trigger time exceeds 50ms.
128 -
129 -
130 -(% style="color:#4f81bd" %)**Example 3: **
131 -
132 -**AT+DI1TODO1= maps value**
133 -
134 -**AT+DI1TORO1= maps value**
135 -
136 -**AT+DI2TODO2= maps value**
137 -
138 -**AT+DI2TORO2= maps value**
139 -
140 -
141 -(% border="1" style="background-color:#f7faff; color:black; width:706px" %)
142 -|=(% style="width: 102px;" %)Maps value|=(% style="width: 331px;" %)DIx to DOx|=(% style="width: 268px;" %)DIx to ROx
143 -|(% style="width:102px" %)0|(% style="width:331px" %)No Action|(% style="width:268px" %)No Action
144 -|(% style="width:102px" %)1|(% style="width:331px" %)If DIx is high, control DOx to output low level, If DIx is low, control DOx to output high level|(% style="width:268px" %)(((
145 -If DIx is high, control ROx to close,
146 -
147 -if DIx is low, control ROx to open
148 -)))
149 -|(% style="width:102px" %)2|(% style="width:331px" %)If DIx is high, control DOx to output high level, If DIx is low, control DOx to output low level|(% style="width:268px" %)(((
150 -If DIx is high, control ROx to open,
151 -
152 -if DIx is low, control ROx to close
153 -)))
154 -|(% style="width:102px" %)3|(% style="width:331px" %)DOx state flip|(% style="width:268px" %)ROx state flip
155 -
156 -(% style="color:#4f81bd" %)**Example 4: **
157 -
158 -**AT+GROUPMOD=0**  Set to point to point mode
159 -
160 -**AT+GROUPMOD=0,aa**  Set the TX group that controls the number of aa (The maximum value of aa is 8)
161 -
162 -**AT+GROUPMOD=1,bb**  Set to the RX group controlled by the TX group, numbered bb(The maximum value of aa is 8)
163 -
164 -**AT+GROUPMOD=0,2**  Set to control the TX group of the two RX groups
165 -
166 -**AT+GROUPMOD=1,1**  Set the RX group numbered 1
167 -
168 -**AT+GROUPMOD=1,2**  Set the RX group numbered 2
169 -
170 -
171 -== **2.4 Data Format** ==
172 -
173 -8 bytes of GROUPID + 9 bytes of payload + 4 bytes of checksum
174 -
175 -
176 -(% style="color:#4f81bd" %)**Payload:**
177 -
178 -(% border="1" style="background-color:#f7faff; color:black; width:938px" %)
179 -|=(% style="width: 123px;" %)**Size (bytes)**|=(% style="width: 107px;" %)1|=(% style="width: 107px;" %)1|=(% style="width: 107px;" %)1|=(% style="width: 107px;" %)1|=(% style="width: 107px;" %)1|=(% style="width: 107px;" %)1|=(% style="width: 107px;" %)1|=(% style="width: 107px;" %)1|=(% style="width: 107px;" %)1
180 -|(% style="width:123px" %)**Value**|(% style="width:38px" %)address|(% style="width:70px" %)request|(% style="width:52px" %)ACK|(% style="width:127px" %)(((
181 -DI1&
182 -
183 -DI1 level
184 -)))|(% style="width:101px" %)DI1TODO1|(% style="width:91px" %)DI1TORO1|(% style="width:111px" %)(((
185 -DI2&
186 -
187 -DI2 level
188 -)))|(% style="width:105px" %)DI2TODO2|(% style="width:106px" %)DI2TORO2
189 -
190 -(% style="color:#037691" %)**The first byte**(%%)**:**  00 is the broadcast address, 01-08 is the RX group number.
191 -
192 -(% style="color:#037691" %)**The second byte**(%%)**:**  send mapping request when not 0, not request when it is 0.
193 -
194 -(% style="color:#037691" %)**The third byte**(%%)**:**  ACK returned to the sender after the mapping is completed.
195 -
196 -(% style="color:#037691" %)**The fourth byte**(%%)**:**  the high four bits are 1 to represent DI1, and the low four bits are the level of DI1 when the interrupt is triggered.
197 -
198 -(% style="color:#037691" %)**The Fifth byte**(%%)**:       **DI1TODO1 when the interrupt is triggered, 0 when the interrupt is not triggered.
199 -
200 -(% style="color:#037691" %)**The Sixth byte**(%%)**:**  0 does not trigger interrupt when DI1TORO1 interrupt is triggered.
201 -
202 -(% style="color:#037691" %)**The seventh byte**(%%)**:**  the high four bits are 2 to represent DI2, and the low four bits are the level of DI2 when the interrupt is triggered.
203 -
204 -(% style="color:#037691" %)**The 8th byte**(%%)**:          **DI2TODO2 when the interrupt is triggered, 0 when the interrupt is not triggered.
205 -
206 -(% style="color:#037691" %)**The 9th byte**(%%)**:**  DI2TORO2 when an interrupt is triggered, 0 when an interrupt is not triggered.
207 -
208 208  

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0