Changes for page Point to Point Communication of LT-22222-L

Last modified by Edwin Chen on 2022/11/22 09:38

From version < 8.2 >

edited by Xiaoling
on 2022/06/02 12:03

To version < 26.1 >

edited by Edwin Chen
on 2022/11/22 09:37

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (3 modified, 0 added, 0 removed)
Attachments (0 modified, 3 added, 0 removed)

Details

Page properties

Title

@@ -1,1 +1,1 @@
-- Point to Point Communication of LT-22222-L
++Point to Point Communication of LT-22222-L

Author

@@ -1,1 +1,1 @@
--XWiki.Xiaoling
++XWiki.Edwin

Content

@@ -1,204 +1,696 @@
--{{box cssClass="floatinginfobox" title="**Contents**"}}
++**Table of Contents： **
++
  {{toc/}}
--{{/box}}
--= **1. Overview** =
++
++
++= 1. Overview =
++
  (((
++
++
  Shipped LT-22222-L is base on LoRaWAN protocol. We also develop a open source Point to Point LoRa protocol for LT-22222-L. The source code and hex file can be found at:
++
++* [[Source Code>>https://github.com/dragino/LT-22222-L]].
++* [[Firmware>>https://github.com/dragino/LT-22222-L/releases]].
  )))
++= 2. Features for this firmware =
++
++== 2.1  Point To Point ==
++
++=== 2.1.1 Overview ===
++
++
++[[image:image-20220602111219-1.png||height="472" width="972"]]
++
++
++=== 2.2.2 Configure ===
++
++
++(% border="1" style="background-color:#f7faff; color:black; width:360px" %)
++|=(% style="width: 179px;" %)**A's configuration**|=(% style="width: 177px;" %)**B's configuration**
++|(% style="width:179px" %)AT+GROUPMOD=0|(% style="width:177px" %)AT+GROUPMOD=0
++|(% style="width:179px" %)AT+TXCHS=868700000|(% style="width:177px" %)AT+TXCHS=869000000
++|(% style="width:179px" %)AT+RXCHS=869000000|(% style="width:177px" %)AT+RXCHS=868700000
++|(% style="width:179px" %)AT+TRIG1=2,50|(% style="width:177px" %)AT+TRIG1=2,50
++|(% style="width:179px" %)AT+TRIG2=2,50|(% style="width:177px" %)AT+TRIG2=2,50
++|(% style="width:179px" %)AT+DI1TODO1=2|(% style="width:177px" %)AT+DI1TODO1=2
++|(% style="width:179px" %)AT+DI1TORO1=2|(% style="width:177px" %)AT+DI1TORO1=2
++|(% style="width:179px" %)AT+DI2TODO2=2 |(% style="width:177px" %)AT+DI2TODO2=2
++|(% style="width:179px" %)AT+DI2TORO2=2|(% style="width:177px" %)AT+DI2TORO2=2
++
++=== 2.2.3 Serial port display ===
++
++
++(% class="wikigeneratedid" %)
++[[image:image-20220602111219-2.png]]
++
++
++(% class="wikigeneratedid" %)
++[[image:image-20220602111219-3.png]]
++
++
++(% class="wikigeneratedid" %)
++If the sender does not get the ACK reply from the receiver, it will retransmit up to 4 times, each interval is 6 seconds, and the UplinkCounter of the retransmission will not increase.
++
++
++== 2.2  Point To Mult-Point ==
++
++=== 2.2.1 Overview ===
++
++
++[[image:1654152390874-192.png]]
++
++
++=== 2.2.2  Configure ===
++
++
++(% style="color:blue" %)**Configuration of the TX group:**
++
++AT+GROUPMOD=0,2
++
++AT+TXCHS=868700000
++
++AT+RXCHS=869000000
++
++AT+TRIG1=2,50
++
++AT+TRIG2=2,50
++
++AT+DI1TODO1=1
++
++AT+DI1TORO1=1
++
++AT+DI2TODO2=1
++
++AT+DI2TORO2=1
++
++
++(% style="color:blue" %)**Configuration for RX group number 1:**
++
++AT+GROUPMOD=1,1
++
++AT+TXCHS=869000000
++
++AT+RXCHS=868700000
++
++
++(% style="color:blue" %)**Configuration for RX group number 2:**
++
++AT+GROUPMOD=1,2
++
++AT+TXCHS=869000000
++
++AT+RXCHS=868700000
++
++
++=== 2.2.3 Serial port display ===
++
++
++[[image:image-20220602144747-1.png]]
++
++
++[[image:image-20220602144747-2.png]]
++
++
  (((
--[[Point to Point Software for LT-22222-L>>https://github.com/dragino/LT-22222-L]].
++If the TX group does not receive all the ACK replies from the RX group, it will retransmit up to 4 times, each time interval is 30 seconds, and the retransmission UplinkCounter will not increase.
  )))
--==   ==
--= **2. Features for this firmware** =
++== 2.3 AT command ==
--== **2.1  Point To Point** ==
++(((
++(% style="color:#037691" %)**ATZ** (%%)**: **           Trig a reset of the MCU
++)))
++(((
++(% style="color:#037691" %)**AT+FDR** (%%)**:**     Reset Parameters to Factory Default, Keys Reserve
++)))
--[[image:image-20220602111219-1.png||height="472" width="972"]]
++(((
++(% style="color:#037691" %)**AT+FCU** (%%)**:**     Get or Set the Frame Counter Uplink
++)))
++(((
++(% style="color:#037691" %)**AT+FCD** (%%)**:**     Get or Set the Frame Counter Downlink
++)))
--(% class="wikigeneratedid" id="H2.2.Configure" %)
--(% style="color:blue" %)**Configure:**
++(((
++(% style="color:#037691" %)**AT+TXP** (%%)**:**     Get or Set the transmit power, the maximum is 20dBm (default is 14dBm)
++)))
++(((
++(% style="color:#037691" %)**AT+SYNC** (%%)**:**  Get or Set the Sync word [1:0x34,0:0x12] (default is 1)
++)))
--(% border="1" style="background-color:#f7faff; color:black; width:500px" %)
--|=**A's configuration**|=**B's configuration**
--|AT+GROUPMOD=0|AT+GROUPMOD=0
--|AT+TXCHS=868700000|AT+TXCHS=869000000
--|AT+RXCHS=869000000|AT+RXCHS=868700000
--|AT+TRIG1=2,50|AT+TRIG1=2,50
--|AT+TRIG2=2,50|AT+TRIG2=2,50
--|AT+DI1TODO1=2|AT+DI1TODO1=2
--|AT+DI1TORO1=2|AT+DI1TORO1=2
--|AT+DI2TODO2=2 |AT+DI2TODO2=2
--|AT+DI2TORO2=2|AT+DI2TORO2=2
++(((
++(% style="color:#037691" %)**AT+PMB** (%%)**:    **Get or Set the preamble (default:8)
++)))
++(((
++(% style="color:#037691" %)**AT+TXCHS **(%%)**:** Get or Set the transmit frequency of TX (default:868700000)
++)))
++(((
++(% style="color:#037691" %)**AT+TXSF **(%%)**:**    Get or Set the spreading factor of TX (7 to 12) (default:12)
++)))
--== **2.2  Point To Mult-Point ** ==
++(((
++(% style="color:#037691" %)**AT+RXCHS **(%%)**:** Get or Set the transmit frequency of RX (default:869000000)
++)))
++(((
++(% style="color:#037691" %)**AT+RXSF **(%%)**:**    Get or Set the spreading factor of RX (7 to 12) (default:12)
++)))
--[[image:image-20220602111219-2.png]]
++(((
++(% style="color:#037691" %)**AT+BW **(%%)**:       **Get or Set the bandwidth [0:125khz,1:250khz,2:500khz] (default:0)
++)))
++(((
++(% style="color:#037691" %)**AT+CR **(%%)**:        **Get or Set the coding rate [1: 4/5, 2: 4/6, 3: 4/7, 4: 4/8] (default:1)
++)))
--[[image:image-20220602111219-3.png]]
++(((
++(% style="color:#037691" %)**AT+TDC **(%%)**:**      Get or set the application data transmission interval in ms(default 10 minutes)
++)))
--If the sender does not get the ACK reply from the receiver, it will retransmit up to 4 times, each interval is 6 seconds, and the UplinkCounter of the retransmission will not increase.
++(((
++(% style="color:#037691" %)**AT+VER **(%%)**:**      Get firmware version number
++)))
++(((
++(% style="color:#037691" %)**AT+SEND **(%%)**:   **Set Custom sent hex data
++)))
--== **2.3 AT command** ==
++(((
++(% style="color:#037691" %)**AT+GROUPMOD **(%%)**: **Set or Get the grouping mode of the device (default: 0)
++)))
++(((
++(((
++(% style="color:#037691" %)**AT+GROUPID **(%%)**:      **Set or Get the password for matching between TX group and RX group, which can be composed of numbers or characters (default: 12345678)
++)))
++)))
--ATZ :        Trig a reset of the MCU
++(((
++(% style="color:#037691" %)**AT+TRIG1 **(%%)**:**            Set or Get the DI1 pin interrupt trigger mode (default 0,0)
++)))
--AT+FDR : Reset Parameters to Factory Default, Keys Reserve
++(((
++(% style="color:#037691" %)**AT+TRIG2 **(%%)**:            **Set or Get the DI2 pin interrupt trigger mode (default 0,0)
++)))
--AT+FCU : Get or Set the Frame Counter Uplink
++(((
++(% style="color:#037691" %)**AT+DI1TODO1 **(%%)**:    **Set or get the mode in which DI1 maps to DO1 (default 0)
++)))
--AT+FCD : Get or Set the Frame Counter Downlink
++(((
++(% style="color:#037691" %)**AT+DI1TORO1 **(%%)**:    **Set or get the mode in which DI1 maps to RO1(default 0)
++)))
--AT+TXP : Get or Set the transmit power, the maximum is 20dBm (default is 14dBm)
++(((
++(% style="color:#037691" %)**AT+DI2TODO2 **(%%)**:**    Set or get the mode in which DI2 maps to DO2(default 0)
++)))
--AT+SYNC : Get or Set the Sync word [1:0x34,0:0x12] (default is 1)
++(((
++(% style="color:#037691" %)**AT+DI2TORO2 **(%%)**:    **Set or get the mode in which DI2 maps to RO2(default 0)
++)))
--AT+PMB : Get or Set the preamble (default:8)
--AT+TXCHS : Get or Set the transmit frequency of TX (default:868700000)
++(((
++(% style="color:blue" %)**Example 1:**
++)))
--AT+TXSF : Get or Set the spreading factor of TX (7 to 12) (default:12)
++(((
++**AT+SEND=01020304 **will send a payload of 01020304
++)))
--AT+RXCHS : Get or Set the transmit frequency of RX (default:869000000)
--AT+RXSF : Get or Set the spreading factor of RX (7 to 12) (default:12)
++(((
++(% style="color:blue" %)**Example 2: **
++)))
--AT+BW : Get or Set the bandwidth [0:125khz,1:250khz,2:500khz] (default:0)
++(((
++**AT+TRIGx=a    **Trigger directly without triggering time
++)))
--AT+CR : Get or Set the coding rate [1: 4/5, 2: 4/6, 3: 4/7, 4: 4/8] (default:1)
++(((
++**AT+TRIGx=a,b**
++)))
--AT+TDC : Get or set the application data transmission interval in ms(default 10 minutes)
++(((
++**a=0:** falling edge;
++)))
--AT+VER : Get firmware version number
++(((
++**a=1: **rising edge;
++)))
--AT+SEND : Set Custom sent hex data
++(((
++**a=2:** falling edge or rising edge;
++)))
--AT+GROUPMOD : Set or Get the grouping mode of the device (default: 0)
++(((
++**b:**     triggering time in milliseconds.
++)))
--AT+GROUPID : Set or Get the password for matching between TX group and RX group, which can be composed of numbers or characters (default: 12345678)
++(((
++**AT+TRIGx=2,50**     Falling edge or rising edge trigger, and the trigger time exceeds 50ms.
++)))
--AT+TRIG1 : Set or Get the DI1 pin interrupt trigger mode (default 0,0)
--AT+TRIG2 : Set or Get the DI2 pin interrupt trigger mode (default 0,0)
++(((
++(% style="color:blue" %)**Example 3: **
++)))
--AT+DI1TODO1 : Set or get the mode in which DI1 maps to DO1 (default 0)
++(((
++**AT+DI1TODO1= maps value**
++)))
--AT+DI1TORO1 : Set or get the mode in which DI1 maps to RO1(default 0)
++(((
++**AT+DI1TORO1= maps value**
++)))
--AT+DI2TODO2 : Set or get the mode in which DI2 maps to DO2(default 0)
++(((
++**AT+DI2TODO2= maps value**
++)))
--AT+DI2TORO2 : Set or get the mode in which DI2 maps to RO2(default 0)
++(((
++**AT+DI2TORO2= maps value**
++)))
++(((
++
++)))
++(% border="1" style="background-color:#f7faff; color:black; width:690px" %)
++|=(% style="width: 102px;" %)(((
++Maps value
++)))|=(% style="width: 331px;" %)(((
++DIx to DOx
++)))|=(% style="width: 251px;" %)(((
++DIx to ROx
++)))
++|(% style="width:102px" %)(((
++0
++)))|(% style="width:331px" %)(((
++No Action
++)))|(% style="width:251px" %)(((
++No Action
++)))
++|(% style="width:102px" %)(((
++1
++)))|(% style="width:331px" %)(((
++If DIx is high, control DOx to output low level, If DIx is low, control DOx to output high level
++)))|(% style="width:251px" %)(((
++(((
++If DIx is high, control ROx to close,
++)))
--i.g. AT+SEND=01020304 will send a payload of 01020304
++(((
++if DIx is low, control ROx to open
++)))
++)))
++|(% style="width:102px" %)(((
++2
++)))|(% style="width:331px" %)(((
++If DIx is high, control DOx to output high level, If DIx is low, control DOx to output low level
++)))|(% style="width:251px" %)(((
++(((
++If DIx is high, control ROx to open,
++)))
++(((
++if DIx is low, control ROx to close
++)))
++)))
++|(% style="width:102px" %)(((
++3
++)))|(% style="width:331px" %)(((
++DOx state flip
++)))|(% style="width:251px" %)(((
++ROx state flip
++)))
--i.g. AT+TRIGx=a    Trigger directly without triggering time
++(((
++
--AT+TRIGx=a,b  a=0, falling edge;
++(% style="color:blue" %)**Example 4: **
++)))
--a=1, rising edge;
++(((
++**AT+GROUPMOD=0**       Set to point to point mode
++)))
--                a=2, falling edge or rising edge.
++(((
++**AT+GROUPMOD=0,aa**  Set the TX group that controls the number of aa (The maximum value of aa is 8)
++)))
--                b, triggering time in milliseconds
++(((
++**AT+GROUPMOD=1,bb**  Set to the RX group controlled by the TX group, numbered bb(The maximum value of aa is 8)
++)))
--  AT+TRIGx=2,50  Falling edge or rising edge trigger, and the trigger time exceeds 50ms
++(((
++**AT+GROUPMOD=0,2**    Set to control the TX group of the two RX groups
++)))
++(((
++**AT+GROUPMOD=1,1**    Set the RX group numbered 1
++)))
--i.g. AT+DI1TODO1= maps value
++(((
++**AT+GROUPMOD=1,2**    Set the RX group numbered 2
++)))
--   AT+DI1TORO1= maps value
--AT+DI2TODO2= maps value
++=== 2.3.1 TRIG command is configured in the transmit LT. (LT1)(Since firmware 1.3.2) ===
--AT+DI2TORO2= maps value
++**AT+TRIGx=a          **Trigger transmit directly without triggering time
++**AT+TRIGx=a,b**       Trigger transmit with triggering time threshold
++**AT+TRIGx=a,b,c    **Trigger transmit with triggering time threshold, and continue to transmit every xx seconds if DI status no change.
--(% style="width:706px" %)
--|(% style="width:102px" %)Maps value|(% style="width:331px" %)DIx to DOx|(% style="width:268px" %)DIx to ROx
--|(% style="width:102px" %)0|(% style="width:331px" %)No Action|(% style="width:268px" %)No Action
--|(% style="width:102px" %)1|(% style="width:331px" %)If DIx is high, control DOx to output low level, If DIx is low, control DOx to output high level|(% style="width:268px" %)(((
++
++**a=0:** falling edge;
++
++**a=1:** rising edge;
++
++**a=2:** falling edge or rising edge;
++
++**b:**   triggering time in milliseconds.
++
++**c:**   transmit interval
++
++
++(% style="color:blue" %)**Use Case 1**(%%):  Once the DI1 port status change ( either from low to high or high to low, LT1 sends a trigger to LT-2)
++
++**Command:**
++
++**AT+TRIG1=2,50**     Falling edge or rising edge trigger, and the trigger time should exceed 50ms.
++
++
++(% style="color:blue" %)**Use Case 2:  **(%%)Sync LT2 RO / DO status with LT1 every minute.
++
++**Command:**
++
++**AT+TRIG2=2,50,60**     Once there is falling edge or rising edge on DI2 of LT1, LT1 will transmit trigger to LT2 and LT2 can sync the status of RO/DO. After power off, power on, LT1 will send trigger without falling/rising edge, so the DI changes during power off will be sync as well.
++
++
++=== 2.3.2 RO/DO is configured in the transmit LT. (LT1) and receiver LT (LT2)(Since firmware 1.3.2) ===
++
++
++(% style="color:red" %)Notice:(%%) LT1 MUST have a AT+DIxTODOx commands to send out the trigger. If LT2 has AT+DIxTOROx configured, LT2 will follow its configured and ignore LT1's AT+DIxTOROx settings.
++
++
++AT+DI1TODO1= maps value[,latch time, timeout_state]
++
++AT+DI1TORO1= maps value[,latch time, timeout_state]
++
++AT+DI2TODO2= maps value[,latch time, timeout_state]
++
++AT+DI2TORO2= maps value[,latch time, timeout_state]
++
++
++(% border="1" style="background-color:#f7faff; color:black; width:774px" %)
++|(% style="width:105px" %) **Maps value**|(% style="width:415px" %)**DIx to DOx**|(% style="width:249px" %)**DIx to ROx**
++|(% style="width:105px" %)0|(% style="width:415px" %)No Action|(% style="width:249px" %)No Action
++|(% style="width:105px" %)1|(% style="width:415px" %)If DIx is high, control DOx to output low level, If DIx is low, control DOx to output high level|(% style="width:249px" %)(((
  If DIx is high, control ROx to close,
  if DIx is low, control ROx to open
  )))
--|(% style="width:102px" %)2|(% style="width:331px" %)If DIx is high, control DOx to output high level, If DIx is low, control DOx to output low level|(% style="width:268px" %)(((
++|(% style="width:105px" %)2|(% style="width:415px" %)If DIx is high, control DOx to output high level, If DIx is low, control DOx to output low level|(% style="width:249px" %)(((
  If DIx is high, control ROx to open,
  if DIx is low, control ROx to close
  )))
--|(% style="width:102px" %)3|(% style="width:331px" %)DOx state flip|(% style="width:268px" %)ROx state flip
++|(% style="width:105px" %)3|(% style="width:415px" %)DOx state flip|(% style="width:249px" %)ROx state flip
--i.g. AT+GROUPMOD=0  Set to point to point mode
++**latch time**, if latch time is defined, DO or RO will go back to the original status after latch time, if there is a new trigger comes, the LT2 will use the new latch time settings and ignore the old one.
--AT+GROUPMOD=0,aa  Set the TX group that controls the number of aa (The maximum value of aa is 8)
--AT+GROUPMOD=1,bb   Set to the RX group controlled by the TX group, numbered bb(The maximum value of aa is 8)
++**Timeout_State**:
++0: **No change** after timeout
--AT+GROUPMOD=0,2  Set to control the TX group of the two RX groups
++1: Change to **DO:0** or **RO: Open** after timeout
--AT+GROUPMOD=1,1  Set the RX group numbered 1
++2: Change to **DO:1** or **RO: Close** after timeout
--AT+GROUPMOD=1,2  Set the RX group numbered 2
++3: Change **back to state** before last trigger arrive.
++(% style="color:blue" %)**Case1**:
--== **2.4 Data Format** ==
++AT+DI1TODO1=1      ~/~/ LT2 DO1 will follow LT1 DI1 trigger command, if DI1 of LT1 is trigger high, DO1 of LT2 will output low, if DI1 of LT1 is trigger low, DO2 of LT2 will output high.
--8 bytes of GROUPID + 9 bytes of payload + 4 bytes of checksum
++(% style="color:blue" %)**Case2**:
--Payload:
++AT+DI1TODO1=1,60,1    ~/~/ LT2 DO1 will follow LT1 DI1 trigger command, DO1 will keep the status 60 seconds and then change to open.
--|**Size (bytes)**|(% colspan="2" %)**1**|(% colspan="2" %)**1**|(% colspan="2" %)**1**|(% colspan="2" %)**1**|**1**
--|**Value**|(% colspan="2" %)address|(% colspan="2" %)request|(% colspan="2" %)ACK|(% colspan="2" %)(((
--DI1&
++=== 2.3.3 Save the RO/DO status during power off(Since firmware 1.3) ===
++
++
++Enable/Disbale retain Digital Output/Relay Output after power off / Power On
++
++**AT+DOROSAVE=0**     ~/~/ Disable Retain after power off/on
++
++**AT+DOROSAVE=1**     ~/~/ Enable Retain after power off/on
++
++**AT+DOROSAVE=2,a,b,c,d**     ~/~/ set DO/RO port to default state after power on.
++
++**a: **for DO1
++
++**b:** for DO2
++
++**c: **for RO1
++
++**d:** for RO2.
++
++
++**Example:**
++
++AT+DOROSAVE=2,0,0,0,1     ~/~/ Set DO1/DO2 to Low, RO1 to open after power on , set RO2 to close after power on.
++
++
++=== 2.3.4 Control Sleep status.(Since firmware 1.3) ===
++
++
++DI2 can be used to set LT into sleep mode.
++
++**AT+DI2SLEEP=1**    ~/~/  Enable DI2 as Sleep pin
++
++**AT+DI2SLEEP=0**    ~/~/  Disable DI2 as Sleep pin
++
++When DI2 is enabled as sleep pin, a falling trigger (with 500ms pulse) will set LT into sleep mode. A raising trigger will wake up it again.
++
++In sleep mode, DORO will keep its initial state if AT+DOROSAVE=2, otherwise DORO will be in OFF state
++
++
++== 2.4 Data Format ==
++
++
++(((
++8 bytes of GROUPID + 9 bytes of payload + 4 bytes of checksum
++)))
++
++(((
++(% style="color:blue" %)**Payload:Payload triggered by TDC or DI**
++)))
++
++(% border="1" style="background-color:#f7faff; color:black; width:825px" %)
++|=(% style="width: 102px;" %)(((
++**Size (bytes)**
++)))|=(% style="width: 74px;" %)(((
++1
++)))|=(% style="width: 72px;" %)(((
++1
++)))|=(% style="width: 47px;" %)(((
++1
++)))|=(% style="width: 83px;" %)(((
++1
++)))|=(% style="width: 90px;" %)(((
++1
++)))|=(% style="width: 92px;" %)(((
++1
++)))|=(% style="width: 78px;" %)(((
++1
++)))|=(% style="width: 91px;" %)(((
++1
++)))|=(% style="width: 91px;" %)(((
++1
++)))
++|(% style="width:102px" %)(((
++**Value**
++)))|(% style="width:74px" %)(((
++address
++)))|(% style="width:72px" %)(((
++request
++)))|(% style="width:47px" %)(((
++ACK
++)))|(% style="width:83px" %)(((
++(((
++DI1&
  DI1 level
--)))|DI1TODO1
--|(% colspan="2" %)**1**|(% colspan="2" %)**1**|(% colspan="2" %)**1**|(% colspan="2" %)**1**|(% colspan="2" %)
--|(% colspan="2" %)DI1TORO1|(% colspan="2" %)(((
++)))
++)))|(% style="width:90px" %)(((
++DI1TODO1
++)))|(% style="width:92px" %)(((
++DI1TORO1
++)))|(% style="width:78px" %)(((
++(((
  DI2&
++DI2 leve
++)))
++)))|(% style="width:91px" %)(((
++DI2TODO2
++)))|(% style="width:91px" %)(((
++DI2TORO2
++)))
--DI2 level
--)))|(% colspan="2" %)DI2TODO2|(% colspan="2" %)DI2TORO2|(% colspan="2" %)
--| | | | | | | | | |
++(((
++(% style="color:#037691" %)**The first byte**(%%)**:**        00 is the broadcast address, 01-08 is the RX group number.
++)))
--The first byte: 00 is the broadcast address, 01-08 is the RX group number
++(((
++(% style="color:#037691" %)**The second byte**(%%)**:**   send mapping request when not 0, not request when it is 0.
++)))
--The second byte: send mapping request when not 0, not request when it is 0
++(((
++(% style="color:#037691" %)**The third byte**(%%)**:**      ACK returned to the sender after the mapping is completed.
++)))
--The third byte: ACK returned to the sender after the mapping is completed
++(((
++(((
++(% style="color:#037691" %)**The fourth byte**(%%)**:**    the high four bits are 1 to represent DI1, and the low four bits are the level of DI1 when the interrupt is triggered.
++)))
++)))
--The fourth byte: the high four bits are 1 to represent DI1, and the low four bits are the level of DI1 when the interrupt is triggered
++(((
++(% style="color:#037691" %)**The Fifth byte**(%%)**:       **DI1TODO1 when the interrupt is triggered, 0 when the interrupt is not triggered.
++)))
--The Fifth byte: DI1TODO1 when the interrupt is triggered, 0 when the interrupt is not triggered
++(((
++(% style="color:#037691" %)**The Sixth byte**(%%)**:**       0 does not trigger interrupt when DI1TORO1 interrupt is triggered.
++)))
--The Sixth byte: 0 does not trigger interrupt when DI1TORO1 interrupt is triggered
++(((
++(((
++(% style="color:#037691" %)**The seventh byte**(%%)**:**  the high four bits are 2 to represent DI2, and the low four bits are the level of DI2 when the interrupt is triggered.
++)))
++)))
--The seventh byte: the high four bits are 2 to represent DI2, and the low four bits are the level of DI2 when the interrupt is triggered
++(((
++(% style="color:#037691" %)**The 8th byte**(%%)**:          **DI2TODO2 when the interrupt is triggered, 0 when the interrupt is not triggered.
++)))
--The 8th byte: DI2TODO2 when the interrupt is triggered, 0 when the interrupt is not triggered
++(((
++(% style="color:#037691" %)**The 9th byte**(%%)**:**          DI2TORO2 when an interrupt is triggered, 0 when an interrupt is not triggered.
++)))
--The 9th byte: DI2TORO2 when an interrupt is triggered, 0 when an interrupt is not triggered
++(((
++
++(% style="color:blue" %)**Payload:（Since firmware 1.3）The receiver replies to the sent packet**
++)))
++
++(% border="1" style="background-color:#f7faff; color:black; width:822px" %)
++|=(% style="width: 97px;" %)(((
++**Size(bytes)**
++)))|=(% style="width: 71px;" %)(((
++1
++)))|=(% style="width: 70px;" %)(((
++1
++)))|=(% style="width: 48px;" %)(((
++1
++)))|=(% style="width: 85px;" %)(((
++1
++)))|=(% style="width: 90px;" %)(((
++1
++)))|=(% style="width: 88px;" %)(((
++1
++)))|=(% style="width: 86px;" %)(((
++1
++)))|=(% style="width: 92px;" %)(((
++1
++)))|=(% style="width: 92px;" %)(((
++1
++)))
++|(% style="width:97px" %)(((
++**Value**
++)))|(% style="width:71px" %)(((
++address
++)))|(% style="width:70px" %)(((
++request
++)))|(% style="width:48px" %)(((
++ACK
++)))|(% style="width:85px" %)(((
++(((
++DOI1&
++DOI2 level
++)))
++)))|(% style="width:90px" %)(((
++DI1TODO1
++)))|(% style="width:88px" %)(((
++DI1TORO1
++)))|(% style="width:86px" %)(((
++(((
++RO2&
++RO2 level
++)))
++)))|(% style="width:92px" %)(((
++DI2TODO2
++)))|(% style="width:92px" %)(((
++DI2TORO2
++)))
++
++(((
++(% style="color:#037691" %)**The first byte**(%%)**:**        00 is the broadcast address, 01-08 is the RX group number.
++)))
++
++(((
++(% style="color:#037691" %)**The second byte**(%%)**:**   send mapping request when not 0, not request when it is 0.
++)))
++
++(((
++(% style="color:#037691" %)**The third byte**(%%)**:**      ACK returned to the sender after the mapping is completed.
++)))
++
++(((
++(((
++(% style="color:#037691" %)**The fourth byte**(%%)**:**    the high four bits are 1 to represent DOI1, and the low four bits are the level of DOI2 when the interrupt is triggered.
++)))
++)))
++
++(((
++(% style="color:#037691" %)**The Fifth byte**(%%)**:       **DI1TODO1 when the interrupt is triggered, 0 when the interrupt is not triggered.
++)))
++
++(((
++(% style="color:#037691" %)**The Sixth byte**(%%)**:**       0 does not trigger interrupt when DI1TORO1 interrupt is triggered.
++)))
++
++(((
++(((
++(% style="color:#037691" %)**The seventh byte**(%%)**:**  the high four bits are 2 to represent RO2, and the low four bits are the level of RO2 when the interrupt is triggered.
++)))
++)))
++
++(((
++(% style="color:#037691" %)**The 8th byte**(%%)**:          **DI2TODO2 when the interrupt is triggered, 0 when the interrupt is not triggered.
++)))
++
++(((
++(% style="color:#037691" %)**The 9th byte**(%%)**:**          DI2TORO2 when an interrupt is triggered, 0 when an interrupt is not triggered.
++)))
++

1654152390874-192.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+287.9 KB

Content

image-20220602144747-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+36.9 KB

Content

image-20220602144747-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+21.9 KB

Content

Changes for page Point to Point Communication of LT-22222-L

Summary

Details

Applications

Navigation