Changes for page Point to Point Communication of LT-22222-L
Last modified by Edwin Chen on 2022/11/22 09:38
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -26,6 +26,7 @@ 26 26 (% class="wikigeneratedid" id="H2.2.Configure" %) 27 27 (% style="color:blue" %)**Configure:** 28 28 29 + 29 29 (% border="1" style="background-color:#f7faff; color:black; width:500px" %) 30 30 |=**A's configuration**|=**B's configuration** 31 31 |AT+GROUPMOD=0|AT+GROUPMOD=0 ... ... @@ -38,7 +38,6 @@ 38 38 |AT+DI2TODO2=2 |AT+DI2TODO2=2 39 39 |AT+DI2TORO2=2|AT+DI2TORO2=2 40 40 41 - 42 42 == **2.2 Point To Mult-Point ** == 43 43 44 44 ... ... @@ -47,9 +47,7 @@ 47 47 48 48 [[image:image-20220602111219-3.png]] 49 49 50 -((( 51 51 If the sender does not get the ACK reply from the receiver, it will retransmit up to 4 times, each interval is 6 seconds, and the UplinkCounter of the retransmission will not increase. 52 -))) 53 53 54 54 55 55 == **2.3 AT command** == ... ... @@ -77,7 +77,7 @@ 77 77 78 78 (% style="color:#037691" %)**AT+RXSF **(%%)**:** Get or Set the spreading factor of RX (7 to 12) (default:12) 79 79 80 -(% style="color:#037691" %)**AT+BW **(%%)**: 78 +(% style="color:#037691" %)**AT+BW **(%%)**: **Get or Set the bandwidth [0:125khz,1:250khz,2:500khz] (default:0) 81 81 82 82 (% style="color:#037691" %)**AT+CR **(%%)**: **Get or Set the coding rate [1: 4/5, 2: 4/6, 3: 4/7, 4: 4/8] (default:1) 83 83 ... ... @@ -85,13 +85,11 @@ 85 85 86 86 (% style="color:#037691" %)**AT+VER **(%%)**:** Get firmware version number 87 87 88 -(% style="color:#037691" %)**AT+SEND **(%%)**: 86 +(% style="color:#037691" %)**AT+SEND **(%%)**: **Set Custom sent hex data 89 89 90 90 (% style="color:#037691" %)**AT+GROUPMOD **(%%)**: **Set or Get the grouping mode of the device (default: 0) 91 91 92 -((( 93 93 (% style="color:#037691" %)**AT+GROUPID **(%%)**: **Set or Get the password for matching between TX group and RX group, which can be composed of numbers or characters (default: 12345678) 94 -))) 95 95 96 96 (% style="color:#037691" %)**AT+TRIG1 **(%%)**:** Set or Get the DI1 pin interrupt trigger mode (default 0,0) 97 97 ... ... @@ -161,9 +161,7 @@ 161 161 162 162 **AT+GROUPMOD=0,aa** Set the TX group that controls the number of aa (The maximum value of aa is 8) 163 163 164 -((( 165 165 **AT+GROUPMOD=1,bb** Set to the RX group controlled by the TX group, numbered bb(The maximum value of aa is 8) 166 -))) 167 167 168 168 **AT+GROUPMOD=0,2** Set to control the TX group of the two RX groups 169 169 ... ... @@ -197,17 +197,13 @@ 197 197 198 198 (% style="color:#037691" %)**The third byte**(%%)**:** ACK returned to the sender after the mapping is completed. 199 199 200 -((( 201 201 (% style="color:#037691" %)**The fourth byte**(%%)**:** the high four bits are 1 to represent DI1, and the low four bits are the level of DI1 when the interrupt is triggered. 202 -))) 203 203 204 204 (% style="color:#037691" %)**The Fifth byte**(%%)**: **DI1TODO1 when the interrupt is triggered, 0 when the interrupt is not triggered. 205 205 206 206 (% style="color:#037691" %)**The Sixth byte**(%%)**:** 0 does not trigger interrupt when DI1TORO1 interrupt is triggered. 207 207 208 -((( 209 209 (% style="color:#037691" %)**The seventh byte**(%%)**:** the high four bits are 2 to represent DI2, and the low four bits are the level of DI2 when the interrupt is triggered. 210 -))) 211 211 212 212 (% style="color:#037691" %)**The 8th byte**(%%)**: **DI2TODO2 when the interrupt is triggered, 0 when the interrupt is not triggered. 213 213