Changes for page NMDS200 - NB-IoT Microwave Radar Distance Sensor User Manual

Last modified by Mengting Qiu on 2024/04/02 17:03

From version < 67.3 >

edited by Xiaoling
on 2022/11/18 09:58

To version < 67.1 >

edited by Xiaoling
on 2022/11/18 09:44

Change comment: Uploaded new attachment "image-20221118094449-6.png", version {1}

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -169,7 +169,7 @@
--= 2.  Use NDS03A to communicate with IoT Server =
++= 2.  Use CPN01 to communicate with IoT Server =
  == 2.1  How it works ==
@@ -254,7 +254,7 @@
  (% style="color:red" %)**Note: if you don't have a CoAP server, you can refer this link to set up a CoAP server: **(%%)[[**http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
--(% style="color:blue" %)**Use below commands in NDS03A:**
++(% style="color:blue" %)**Use below commands in CPN01:**
  * (% style="color:#037691" %)**AT+PRO=1**                (%%)                                ~/~/ Set to use CoAP protocol to uplink
@@ -267,7 +267,7 @@
  [[image:image-20221021110948-8.png]]
--After configuring the server address and (% style="color:green" %)**reset NDS03A**(%%) (via AT+ATZ ), NDS03A will start to uplink sensor values to the CoAP server.
++After configuring the server address and (% style="color:green" %)**reset CPN01**(%%) (via AT+ATZ ), NDS03A will start to uplink sensor values to the CoAP server.
  [[image:image-20221021110956-9.png]]
@@ -534,9 +534,10 @@
  The NDS03A has an internal LED which is to show the status of different states.
  * When the device starts normally, the LED will light up for 1 second.
--* After NDS03A join NB-IoT network. The LED will be ON for 3 seconds.
++* After CPN01 join NB-IoT network. The LED will be ON for 3 seconds.
  * For each uplink probe, LED will be on for 500ms.
++
  == 2.7  Alarm Base on Timeout ==
@@ -563,7 +563,7 @@
  (% style="color:blue" %)**PB14 PIN:**
--(% style="color:#037691" %)**AT+TTRIG=1,30** (%%)  **~-~->**  When the **Keep Status** change from connected to disconnect, and device remains in disconnect status for more than 30 seconds. NDS03A will send an uplink packet, the [[Alarm bit>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/#H2.3.3Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2]] (the second bit of 1^^st^^ byte of payload) on this uplink packet is set to 1.
++(% style="color:#037691" %)**AT+TTRIG=1,30** (%%)  **~-~->**  When the **Keep Status** change from connected to disconnect, and device remains in disconnect status for more than 30 seconds. CPN01 will send an uplink packet, the [[Alarm bit>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/#H2.3.3Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2]] (the second bit of 1^^st^^ byte of payload) on this uplink packet is set to 1.
  (% style="color:#037691" %)**AT+TTRIG=0,0 **  (%%)    **~-~->** Default Value, disable timeout Alarm.
@@ -672,13 +672,13 @@
--== 2.17  Battery Analysis ==
++== 2.16  Battery Analysis ==
--=== 2.17.1  Battery Type ===
++=== 2.16.1  Battery Type ===
--The NDS03A battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
++The CPN01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
  The battery is designed to last for several years depends on the actual use environment and update interval.
@@ -694,7 +694,7 @@
--=== 2.17.2  Power consumption Analyze ===
++=== 2.16.2  Power consumption Analyze ===
  Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
@@ -717,7 +717,7 @@
--=== 2.17.3  Battery Note ===
++=== 2.16.3  Battery Note ===
  The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
@@ -724,10 +724,10 @@
--=== 2.17.4  Replace the battery ===
++=== 2.16.4  Replace the battery ===
--The default battery pack of NDS03A includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
++The default battery pack of CPN01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
@@ -738,7 +738,7 @@
  The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]]
--[[image:image-20221118094449-6.png]]
++[[image:image-20221021112006-28.png]]
@@ -791,21 +791,15 @@
  AT+ DEBUG   : Enable or Disable debug mode
--AT+ TTRIG1   : Get or Set PB14 PIN Alarm Base on Timeout
++AT+ TTRIG   : Get or Set Alarm Base on Timeout
--AT+ TTRIG2   : Get or Set PB15 PIN Alarm Base on Timeout
++AT+ TTRMOD   : Get or Set the trigger interrupt mode(0:falling,1:rising)
--AT+COUNTMOD  :   Get or Set the count mode
++AT+ CALCFLAG   : Get or Set the calculate flag
--AT+TTRCHANNEL  : Get or Set the number of interrupt channels
++AT+ CLRC   : Clear current door open count
--AT+TTRALARM  : Get or Set TTRIG1 of Alarm interval (unit: minute)
--AT+DISALARM  : Enable/Disable Alarm for door open/close or water leak event
--
--AT+ CLRC   :        Clear current door open count
--
--
  (% style="color:blue" %)**COAP Management**
  AT+URI            : Resource parameters
@@ -847,7 +847,7 @@
  Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
--(% style="color:red" %)**Notice: **(% style="color:blue" %)**NDS03A** (%%)**and (% style="color:blue" %)LDS03A(%%)**(% style="color:blue" %) (%%)**share the same mother board. They use the same connection and method to update.**
++(% style="color:red" %)**Notice: **(% style="color:blue" %)**CPN01** (%%)**and (% style="color:blue" %)CPL01(%%)**(% style="color:blue" %) (%%)**share the same mother board. They use the same connection and method to update.**
@@ -871,7 +871,7 @@
  = 7.  Order Info =
--Part Number**:** NDS03A
++Part Number**:** CPN01
@@ -880,8 +880,14 @@
  (% style="color:blue" %)**Package Includes**:
--* NDS03A Open/Close Door Sensor x 1
++* CPN01 Open/Close Sensor x 1
++* External antenna x 1
++(% style="color:blue" %)**Dimension and weight**:
++
++* Size: 195 x 125 x 55 mm
++* Weight:   420g
++
  = 9.  Support =

Changes for page NMDS200 - NB-IoT Microwave Radar Distance Sensor User Manual

Summary

Details

Applications

Navigation