Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -59,7 +59,6 @@
59	59	* 4000mAh or 8500mAh Battery for long term use
60	60
61	61
62		-
63	63	== 1.3 Specification ==
64	64
65	65	Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
...	...	@@ -632,6 +632,8 @@
632	632	* Solid ON for 5 seconds once device successful Join the network.
633	633	* Blink once when device transmit a packet.
634	634
	634	+
	635	+
635	635	== 2.9 Installation in Soil ==
636	636
637	637	**Measurement the soil surface**
...	...	@@ -879,20 +879,38 @@
879	879
880	880	== 4.1 ​How to change the LoRa Frequency Bands/Region? ==
881	881
	883	+(((
882	882	You can follow the instructions for [[how to upgrade image>>||anchor="H2.10200BFirmwareChangeLog"]].
883	883	When downloading the images, choose the required image file for download. ​
	886	+)))
884	884
	888	+(((
	889	+
	890	+)))
885	885
	892	+(((
886	886	How to set up LSE01 to work in 8 channel mode By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.
	894	+)))
887	887
	896	+(((
	897	+
	898	+)))
888	888
	900	+(((
889	889	You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.
	902	+)))
890	890
	904	+(((
	905	+
	906	+)))
891	891
	908	+(((
892	892	For example, in **US915** band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.
	910	+)))
893	893
894	894	[[image:image-20220606154726-3.png]]
895	895
	914	+
896	896	When you use the TTN network, the US915 frequency bands use are:
897	897
898	898	* 903.9 - SF7BW125 to SF10BW125
...	...	@@ -905,7 +905,9 @@
905	905	* 905.3 - SF7BW125 to SF10BW125
906	906	* 904.6 - SF8BW500
907	907
	927	+(((
908	908	Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN network and uplink data. To solve this issue, you can access the device via the AT commands and run:
	929	+)))
909	909
910	910	(% class="box infomessage" %)
911	911	(((
...	...	@@ -917,10 +917,17 @@
917	917	**ATZ**
918	918	)))
919	919
	941	+(((
920	920	to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.
	943	+)))
921	921
	945	+(((
	946	+
	947	+)))
922	922
	949	+(((
923	923	The **AU915** band is similar. Below are the AU915 Uplink Channels.
	951	+)))
924	924
925	925	[[image:image-20220606154825-4.png]]
926	926