LT-22222-L LoRa IO Controller User Manual

The Dragino LT series I/O Modules are Long Range LoRaWAN I/O Controller. It contains different I/O Interfaces such as: analog current Input, analog voltage input, relay output, digital input and digital output etc. The LT I/O Modules are designed to simplify the installation of I/O monitoring.

15

)))

16

17

(((

18

The LT I/O Controllers allows the user to send data and reach extremely long ranges. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

)))

(((

The LT I/O Controllers is aiming to provide a simple plug and play, low cost installation by using LoRaWAN wireless technology.

)))

(((

The use environment includes:

)))

(((

1) If user’s area has LoRaWAN service coverage, they can just install the I/O controller and configure it to connect the LoRaWAN provider via wireless.

)))

(((

2) User can set up a LoRaWAN gateway locally and configure the controller to connect to the gateway via wireless.

)))

(((

[[image:1653295757274-912.png]]

39

)))

40

41

== 1.2 Specifications ==

**Hardware System:**

* STM32L072CZT6 MCU

* SX1276/78 Wireless Chip

47

* Power Consumption:

48

** Idle: 4mA@12v

49

** 20dB Transmit: 34mA@12v

50

51

**Interface for Model: LT22222-L:**

52

53

* 2 x Digital dual direction Input (Detect High/Low signal, Max: 50v, or 220v with optional external resistor)

54

* 2 x Digital Output (NPN output. Max pull up voltage 36V,450mA)

55

* 2 x Relay Output (5A@250VAC / 30VDC)

56

* 2 x 0~~20mA Analog Input (res:0.01mA)

57

* 2 x 0~~30V Analog Input (res:0.01v)

58

* Power Input 7~~ 24V DC.

**LoRa Spec:**

* Frequency Range:

** Band 1 (HF): 862 ~~ 1020 Mhz

64

** Band 2 (LF): 410 ~~ 528 Mhz

65

* 168 dB maximum link budget.

66

* +20 dBm - 100 mW constant RF output vs.

67

* +14 dBm high efficiency PA.

68

* Programmable bit rate up to 300 kbps.

69

* High sensitivity: down to -148 dBm.

70

* Bullet-proof front end: IIP3 = -12.5 dBm.

71

* Excellent blocking immunity.

72

* Low RX current of 10.3 mA, 200 nA register retention.

73

* Fully integrated synthesizer with a resolution of 61 Hz.

74

* FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.

75

* Built-in bit synchronizer for clock recovery.

76

* Preamble detection.

77

* 127 dB Dynamic Range RSSI.

78

* Automatic RF Sense and CAD with ultra-fast AFC.

79

* Packet engine up to 256 bytes with CRC.

== 1.3 Features ==

* LoRaWAN Class A & Class C protocol

84

* Optional Customized LoRa Protocol

85

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/RU864/IN865

86

* AT Commands to change parameters

87

* Remote configure parameters via LoRa Downlink

88

* Firmware upgradable via program port

89

* Counting

90

91

== 1.4 Applications ==

92

93

* Smart Buildings & Home Automation

94

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

== 1.5 Hardware Variants ==

101

102

(% border="1" style="background-color:#f7faff; width:540px" %)

103

|(% style="width:103px" %)**Model**|(% style="width:131px" %)**Photo**|(% style="width:334px" %)**Description**

104

|(% style="width:103px" %)**LT22222-L**|(% style="width:131px" %)[[image:1653296302983-697.png]]|(% style="width:334px" %)(((

105

* 2 x Digital Input (Bi-direction)

106

* 2 x Digital Output

107

* 2 x Relay Output (5A@250VAC / 30VDC)

108

* 2 x 0~~20mA Analog Input (res:0.01mA)

109

* 2 x 0~~30V Analog Input (res:0.01v)

* 1 x Counting Port

)))

= 2. Power ON Device =

114

115

The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.

116

117

(((

118

PWR will on when device is properly powered.

119

)))

120

121

[[image:1653297104069-180.png]]

122

123

= 3. Operation Mode =

124

125

== 3.1 How it works? ==

126

127

The LT is configured as LoRaWAN OTAA Class C mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the LT. It will auto join the network via OTAA. For LT-22222-L, the LED will show the Join status: After power on **TX LED** will fast blink 5 times, LT-22222-L will enter working mode and start to JOIN LoRaWAN network. **TX LED** will be on for 5 seconds after joined in network. When there is message from server, the **RX LED** will be on for 1 second.

128

129

In case user can’t set the OTAA keys in the network server and has to use the existing keys from server. User can [[use AT Command>>path:#AT_Command]] to set the keys in the devices.

130

131

3.2 Example to join LoRaWAN network

132

133

This chapter shows an example for how to join the TTN LoRaWAN Network. Below is the network structure, we use our LG308 as LoRaWAN gateway here.

134

135

[[image:image-20220523172350-1.png||height="266" width="864"]]

(((

The LG308 is already set to connect to [[TTN network >>url:https://www.thethingsnetwork.org/]]. So what we need to do now is only configure register this device to TTN:

)))

(((

**Step 1**: Create a device in TTN with the OTAA keys from LT IO controller.

)))

(((

Each LT is shipped with a sticker with the default device EUI as below:

)))

Input these keys in the LoRaWAN Server portal. Below is TTN screen shot:

153

154

Add APP EUI in the application.

155

156

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image007.png]]

157

158

Add APP KEY and DEV EUI

159

160

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image008.png]]

161

162

**Step 2**: Power on LT and it will auto join to the TTN network. After join success, it will start to upload message to TTN and user can see in the panel.

163

164

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image009.png]]

1.

11. Uplink Payload

There are five working modes + one interrupt mode on LT for different type application:

171

172

* [[MOD1>>path:#MOD1]]: (default setting): 2 x ACI + 2AVI + DI + DO + RO

173

* [[MOD2>>path:#MOD2]]: Double DI Counting + DO + RO

174

* [[MOD3>>path:#MOD3]]: Single DI Counting + 2 x ACI + DO + RO

175

* [[MOD4>>path:#MOD4]]: Single DI Counting + 1 x Voltage Counting + DO + RO

176

* [[MOD5>>path:#MOD5]]: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO

177

* [[ADDMOD6>>path:#MOD6]]: Trigger Mode, Optional, used together with MOD1 ~~ MOD5

1.

11.

111. AT+MOD=1, 2ACI+2AVI

183

184

The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.

185

186

187

|Size(bytes)|2|2|2|2|1|1|1

|Value|(((

AVI1

voltage

)))|(((

AVI2

voltage

)))|(((

ACI1

Current

)))|(((

ACI2

Current

)))|DIDORO*|(((

Reserve

)))|MOD

**DIDORO** is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below

212

213

|bit7|bit6|bit5|bit4|bit3|bit2|bit1|bit0

214

|RO1|RO2|DI3|DI2|DI1|DO3|DO2|DO1

215

216

* RO is for relay. ROx=1 : close，ROx=0 always open.

217

* DI is for digital input. DIx=1: high or float, DIx=0: low.

218

* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.

219

220

Note: DI3 and DO3 bit are not valid for LT-22222-L

221

222

223

For example if payload is: 04 AB 04 AC 13 10 13 00 AA FF 01

224

225

The value for the interface is:

226

227

AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V

228

229

AVI2 channel voltage is 0x04AC/1000=1.196V

230

231

ACI1 channel current is 0x1310/1000=4.880mA

232

233

ACI2 channel current is 0x1300/1000=4.864mA

234

235

The last byte 0xAA= 10101010(B) means

236

237

* [1] RO1 relay channel is close and the RO1 LED is ON.

238

* [0] RO2 relay channel is open and RO2 LED is OFF;

LT33222-L:

* [1] DI3 channel is high input and DI3 LED is OFF;

243

* [0] DI2 channel is low input;

244

* [1] DI1 channel is high input and DI1 LED is OFF;

LT22222-L:

* [1] DI2 channel is high input and DI2 LED is ON;

249

* [0] DI1 channel is low input;

250

251

252

* [0] DO3 channel output state

253

** DO3 is float in case no load between DO3 and V+.;

254

** DO3 is high in case there is load between DO3 and V+.

255

** DO3 LED is off in both case

256

* [1] DO2 channel output is low and DO2 LED is ON.

257

* [0] DO1 channel output state

258

** DO1 is float in case no load between DO1 and V+.;

259

** DO1 is high in case there is load between DO1 and V+.

260

** DO1 LED is off in both case

1.

11.

111. AT+MOD=2, (Double DI Counting)

267

268

**For LT-33222-L**: this mode the **DI3** is used as a counting pin. Counting on DI3 reflect in COUNT1.

269

270

**For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.

271

272

273

Total : 11 bytes payload

274

275

|Size(bytes)|4|4|1|1|1

Reserve

)))|MOD

**DIDORO** is a combination for RO1, RO2, DO3, DO2 and DO1. Totally 1bytes as below

284

285

|bit7|bit6|bit5|bit4|bit3|bit2|bit1|bit0

286

|RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1

287

288

* RO is for relay. ROx=1 : close，ROx=0 always open.

289

* FIRST: Indicate this is the first packet after join network.

290

* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.

291

292

Note: DO3 bit is not valid for LT-22222-L.

293

294

295

To use counting mode, please run:

AT+MOD=2

ATZ

AT Commands for counting:

**For LT33222-L:**

AT+TRIG1=0,100 (set DI3 port to trigger on low level, valid signal is 100ms)

307

308

AT+TRIG1=1,100 (set DI3 port to trigger on high level, valid signal is 100ms )

309

310

AT+SETCNT=1,60 (Set COUNT1 value to 60)

**For LT22222-L:**

AT+TRIG1=0,100 (set DI1 port to trigger on low level, valid signal is 100ms)

316

317

AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms )

318

319

AT+TRIG2=0,100 (set DI2 port to trigger on low level, valid signal is 100ms)

320

321

AT+TRIG2=1,100 (set DI2 port to trigger on high level, valid signal is 100ms )

322

323

324

AT+SETCNT=1,60 (Set COUNT1 value to 60)

325

326

AT+SETCNT=2,60 (Set COUNT2 value to 60)

327

328

329

**For both LT22222-L & LT33222-L**:

330

331

AT+CLRCOUNT clear all countings

332

333

AT+COUTIME=60 Set save time to 60 seconds. Device will save the counting result in internal flash every 60 seconds. (min value: 30)

1.

11.

111. AT+MOD=3, Single DI Counting + 2 x ACI

340

341

**LT33222-L**: This mode the DI3 is used as a counting pin.

342

343

**LT22222-L**: This mode the DI1 is used as a counting pin.

344

345

346

|Size(bytes)|4|2|2|1|1|1

|Value|COUNT1|(((

ACI1

Current

)))|(((

ACI2

Current

)))|DIDORO*|Reserve|MOD

356

357

358

**DIDORO** is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below

359

360

|bit7|bit6|bit5|bit4|bit3|bit2|bit1|bit0

361

|RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1

362

363

* RO is for relay. ROx=1 : close，ROx=0 always open.

364

* FIRST: Indicate this is the first packet after join network.

365

* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.

366

367

Note: DO3 is not valid for LT-22222-L.

368

369

370

To use counting mode, please run:

AT+MOD=3

ATZ

Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].

1.

11.

111. AT+MOD=4, Single DI Counting + 1 x Voltage Counting

385

386

**LT33222-L**: This mode the DI3 is used as a counting pin.

387

388

**LT22222-L**: This mode the DI1 is used as a counting pin.

389

390

391

The AVI1 is also used for counting. AVI1 is used to monitor the voltage. It will check the voltage **every 60s**, if voltage is higher or lower than VOLMAX mV, the AVI1 Counting increase 1, so AVI1 counting can be used to measure a machine working hour.

392

393

394

|Size(bytes)|4|4|1|1|1

Reserve

)))|MOD

**DIDORO** is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below

403

404

|bit7|bit6|bit5|bit4|bit3|bit2|bit1|bit0

405

|RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1

406

407

* RO is for relay. ROx=1 : close，ROx=0 always open.

408

* FIRST: Indicate this is the first packet after join network.

409

* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.

410

411

Note: DO3 is not valid for LT-22222-L.

412

413

414

To use this mode, please run:

AT+MOD=4

ATZ

Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].

423

424

Plus below command for AVI1 Counting:

425

426

AT+SETCNT=3,60 (set AVI Count to 60)

427

428

AT+VOLMAX=20000 (If AVI1 voltage higher than VOLMAX (20000mV =20v), counter increase 1)

429

430

AT+VOLMAX=20000,0 (If AVI1 voltage lower than VOLMAX (20000mV =20v), counter increase 1)

431

432

AT+VOLMAX=20000,1 (If AVI1 voltage higer than VOLMAX (20000mV =20v), counter increase 1)

1.

11.

111. AT+MOD=5, Single DI Counting + 2 x AVI + 1 x ACI

439

440

441

**LT33222-L**: This mode the DI3 is used as a counting pin.

442

443

**LT22222-L**: This mode the DI1 is used as a counting pin.

444

445

446

|Size(bytes)|2|2|2|2|1|1|1

|Value|(((

AVI1

voltage

)))|(((

AVI2

voltage

)))|(((

ACI1

Current

)))|COUNT1|DIDORO*|(((

Reserve

)))|MOD

**DIDORO** is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below

468

469

|bit7|bit6|bit5|bit4|bit3|bit2|bit1|bit0

470

|RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1

471

472

* RO is for relay. ROx=1 : close，ROx=0 always open.

473

* FIRST: Indicate this is the first packet after join network.

474

* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.

475

476

Note: DO3 is not valid for LT-22222-L.

477

478

479

To use this mode, please run:

AT+MOD=5

ATZ

Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].

1.

11.

111. AT+ADDMOD=6. (Trigger Mode, Optional)

495

496

497

**This mode is an optional mode for trigger purpose. It can run together with other mode.**

498

499

For example, if user has configured below commands:

500

501

* AT+MOD=1 à The normal working mode

502

* AT+ADDMOD6=1 à Enable trigger

503

504

505

LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:

506

507

1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN **unconfirmed** data type

508

1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN **CONFIRMED data type.**

509

510

511

**AT Command to set Trigger Condition**:

512

513

**Trigger base on voltage**:

514

515

Format: AT+AVLIM=<AV1_LIMIT_LOW>,< AV1_LIMIT_HIGH>,<AV2_LIMIT_LOW>,< AV2_LIMIT_HIGH>

Example:

AT+AVLIM=3000,6000,0,2000 (If AVI1 voltage lower than 3v or higher than 6v. or AV2 voltage is higher than 2v, LT will trigger Uplink)

520

521

AT+AVLIM=5000,0,0,0 (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)

522

523

524

**Trigger base on current**:

525

526

Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>

Example:

AT+ACLIM=10000,15000,0,0 (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)

531

532

533

**Trigger base on DI status**:

534

535

DI status trigger Flag.

536

537

Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >

Example:

AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger)

**Downlink Command to set Trigger Condition**

548

549

Type Code: 0xAA. Downlink command same as AT Command [[AT+AVLIM, AT+ACLIM>>path:#AT_Trigger]]

550

551

Format: AA xx yy1 yy1 yy2 yy2 yy3 yy3 yy4 yy4

552

553

AA: Code for this downlink Command:

554

555

xx: 0: Limit for AV1 and AV2; 1: limit for AC1 and AC2 ; 2 DI1, DI2 trigger enable/disable

556

557

yy1 yy1: AC1 or AV1 low limit or DI1/DI2 trigger status.

558

559

yy2 yy2: AC1 or AV1 high limit.

560

561

yy3 yy3: AC2 or AV2 low limit.

562

563

Yy4 yy4: AC2 or AV2 high limit.

564

565

566

Example1: AA 00 13 88 00 00 00 00 00 00

567

568

Same as AT+AVLIM=5000,0,0,0 (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)

569

570

Example2: AA 02 01 00

571

572

Same as AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger)

**Trigger Settings Payload Explanation:**

578

579

MOD6 Payload : total 11 bytes payload

580

581

|Size(bytes)|1|1|1|6|1|1

|Value|(((

TRI_A

FLAG

)))|(((

TRI_A

Status

)))|(((

TRI_DI

FLAG+STA

)))|Reserve|Enable/Disable MOD6|(((

MOD

(6)

)))

**TRI FLAG1** is a combination to show if trigger is set for this part. Totally 1byte as below

603

604

|bit7|bit6|bit5|bit4|bit3|bit2|bit1|bit0

|(((

AV1_

LOW

)))|(((

AV1_

HIGH

)))|(((

AV2_

LOW

)))|(((

AV2_

HIGH

)))|(((

AC1_

LOW

)))|(((

AC1_

HIGH

)))|(((

AC2_

LOW

)))|(((

AC2_

HIGH

)))

* Each bits shows if the corresponding trigger has been configured.

Example:

10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW

644

645

646

**TRI Status1** is a combination to show which condition is trigger. Totally 1byte as below

647

648

|bit7|bit6|bit5|bit4|bit3|bit2|bit1|bit0

|(((

AV1_

LOW

)))|(((

AV1_

HIGH

)))|(((

AV2_

LOW

)))|(((

AV2_

HIGH

)))|(((

AC1_

LOW

)))|(((

AC1_

HIGH

)))|(((

AC2_

LOW

)))|(((

AC2_

HIGH

)))

* Each bits shows which status has been trigger on this uplink.

Example:

10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.

**TRI_DI FLAG+STA **is a combination to show which condition is trigger. Totally 1byte as below

693

694

|bit7|bit6|bit5|bit4|bit3|bit2|bit1|bit0

695

|N/A|N/A|N/A|N/A|DI2_STATUS|DI2_FLAG|DI1_STATUS|DI1_FLAG

696

697

* Each bits shows which status has been trigger on this uplink.

Example:

00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.

702

703

00000101: Means both DI1 and DI2 trigger are enabled.

704

705

706

**Enable/Disable MOD6 **: 0x01: MOD6 is enable. 0x00: MOD6 is disable.

707

708

709

Downlink command to poll MOD6 status:

AB 06

When device got this command, it will send the MOD6 payload.

1.

11.

111. Payload Decoder

**Decoder for TTN/loraserver/ChirpStack**: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/Payload_decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/Payload_decoder/]]

1.

11. Configure LT via AT or Downlink

731

732

User can configure LT I/O Controller via [[AT Commands >>path:#_Using_the_AT]]or LoRaWAN Downlink Commands

733

734

There are two kinds of Commands:

735

736

* **Common Commands**: They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

737

738

* **Sensor Related Commands**: These commands are special designed for LT-22222-L. User can see these commands below:

1.

11.

111. Common Commands:

744

745

746

They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

1.

11.

111. Sensor related commands:

752

753

754

==== Set Transmit Interval ====

755

756

Set device uplink interval.

* AT Command:

AT+TDC=N

Example: AT+TDC=30000. Means set interval to 30 seconds

763

764

765

* Downlink Payload (prefix 0x01):

766

767

0x01 aa bb cc ~/~/ Same as AT+TDC=0x(aa bb cc)

768

769

770

==== Set Work Mode (AT+MOD) ====

Set work mode.

* AT Command:

AT+MOD=N

Example: AT+MOD=2. Set work mode to Double DI counting mode

779

780

781

* Downlink Payload (prefix 0x0A):

782

783

0x0A aa ~/~/ Same as AT+MOD=aa

==== Poll an uplink ====

* AT Command:

There is no AT Command to poll uplink

792

793

794

* Downlink Payload (prefix 0x08):

795

796

0x08 FF ~/~/ Poll an uplink,

797

798

Example: 0x08FF, ask device to send an Uplink

799

800

801

==== Enable Trigger Mode ====

802

803

Use of trigger mode, please check [[ADDMOD6>>path:#MOD6]]

* AT Command:

AT+ADDMOD6=1 or 0

1: Enable Trigger Mode

810

811

0: Disable Trigger Mode

812

813

814

* Downlink Payload (prefix 0x0A 06):

815

816

0x0A 06 aa ~/~/ Same as AT+ADDMOD6=aa,

817

818

819

==== Poll trigger settings ====

820

821

Poll trigger settings,

* AT Command:

There is no AT Command for this feature.

826

827

828

* Downlink Payload (prefix 0x AB 06):

829

830

0xAB 06 ~/~/ Poll trigger settings, device will uplink [[trigger settings>>path:#Trigger_Settings]] once receive this command

831

832

833

==== Enable / Disable DI1/DI2/DI3 as trigger ====

834

835

Enable Disable DI1/DI2/DI2 as trigger,

* AT Command:

Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >

Example:

AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger)

* Downlink Payload (prefix 0xAA 02):

848

849

0xAA 02 aa bb ~/~/ Same as AT+DTRI=aa,bb

==== Trigger1 – Set DI1 or DI3 as trigger ====

854

855

Set DI1 or DI3(for LT-33222-L) trigger.

* AT Command:

AT+TRIG1=a,b

a : Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).

b : delay timing.

Example:

AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms )

868

869

870

* Downlink Payload (prefix 0x09 01 ):

871

872

0x09 01 aa bb cc ~/~/ same as AT+TRIG1=aa,0x(bb cc)

873

874

875

==== Trigger2 – Set DI2 as trigger ====

Set DI2 trigger.

* AT Command:

AT+TRIG2=a,b

a : Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).

b : delay timing.

Example:

AT+TRIG2=0,100(set DI1 port to trigger on low level, valid signal is 100ms )

890

891

892

* Downlink Payload (prefix 0x09 02 ):

893

894

0x09 02 aa bb cc ~/~/ same as AT+TRIG1=aa,0x(bb cc)

895

896

897

==== Trigger – Set AC (current) as trigger ====

898

899

Set current trigger , base on AC port. See [[trigger mode>>path:#MOD6]]

* AT Command:

AT+ACLIM. See [[trigger mode>>path:#MOD6]]

904

905

906

* Downlink Payload (prefix 0xAA 01 ):

907

908

0x AA 01 aa bb cc dd ee ff gg hh ~/~/ same as AT+ACLIM See [[trigger mode>>path:#MOD6]]

909

910

911

==== Trigger – Set AV (voltage) as trigger ====

912

913

Set current trigger , base on AV port. See [[trigger mode>>path:#MOD6]]

* AT Command:

AT+AVLIM. See [[trigger mode>>path:#MOD6]]

918

919

920

* Downlink Payload (prefix 0xAA 00 ):

921

922

0x AA 00 aa bb cc dd ee ff gg hh ~/~/ same as AT+AVLIM See [[trigger mode>>path:#MOD6]]

923

924

==== Trigger – Set minimum interval ====

925

926

Set AV and AC trigger minimum interval, system won’t response to the second trigger within this set time after the first trigger.

* AT Command:

AT+ATDC=5. Device won’t response the second trigger within 5 minute after the first trigger.

931

932

933

* Downlink Payload (prefix 0xAC ):

934

935

0x AC aa bb ~/~/ same as AT+ATDC=0x(aa bb) . Unit (min)

936

937

938

==== DO ~-~- Control Digital Output DO1/DO2/DO3 ====

* AT Command:

There is no AT Command to control Digital Output

943

944

945

* Downlink Payload (prefix 0x02):

946

947

0x02 aa bb cc ~/~/ Set DO1/DO2/DO3 output

948

949

If payload = 0x02010001, while there is load between V+ and DOx, it means set DO1 to low, DO2 to high and DO3 to low.

950

951

01: Low, 00: High , 11: No action

952

953

|Downlink Code|DO1|DO2|DO3

954

|02 01 00 11|Low|High|No Action

955

|02 00 11 01|High|No Action|Low

956

|02 11 01 00|No Action|Low|High

957

958

Note: For LT-22222-L, there is no DO3, the last byte can use any value.

959

960

Device will upload a packet if downlink code executes successfully.

==== DO ~-~- Control Digital Output DO1/DO2/DO3 with time control ====

* AT Command:

There is no AT Command to control Digital Output

971

972

973

* Downlink Payload (prefix 0xA9):

974

975

0xA9 aa bb cc ~/~/ Set DO1/DO2/DO3 output with time control

976

977

This is to control the digital output time of DO pin. Include four bytes:

978

979

**First Byte:** Type code (0xA9)

980

981

**Second Byte**: Inverter Mode

982

983

01: DO pins will change back to original state after timeout.

984

985

00: DO pins will change to an inverter state after timeout

986

987

988

**Third Byte**: Control Method and Ports status:

|Second Byte|Status

|0x01|DO1 set to low

|0x00|DO1 set to high

|0x11|DO1 NO Action

**Fourth Byte**: Control Method and Ports status:

|Second Byte|Status

|0x01|DO2 set to low

|0x00|DO2 set to high

|0x11|DO2 NO Action

**Fifth Byte**: Control Method and Ports status:

|Second Byte|Status

|0x01|DO3 set to low

|0x00|DO3 set to high

1009

|0x11|DO3 NO Action

1010

1011

**Sixth and Seventh Byte**:

1012

1013

Latching time. Unit: ms

1014

1015

Device will upload a packet if downlink code executes successfully.

Example payload:

1. A9 01 01 01 01 07 D0

1022

1023

DO1 pin & DO2 pin & DO3 pin will be set to Low, last 2 seconds, then change back to original state.

1024

1025

1026

1. A9 01 00 01 11 07 D0

1027

1028

DO1 pin set high, DO2 pin set low, DO3 pin no action, last 2 seconds, then change back to original state.

1029

1030

1031

1. A9 00 00 00 00 07 D0

1032

1033

DO1 pin & DO2 pin & DO3 pin will be set to high, last 2 seconds, then both change to low.

1034

1035

1036

1. A9 00 11 01 00 07 D0

1037

1038

DO1 pin no action, DO2 pin set low, DO3 pin set high, last 2 seconds, then DO1 pin no action, DO2 pin set high, DO3 pin set low

==== Relay ~-~- Control Relay Output RO1/RO2 ====

* AT Command:

There is no AT Command to control Relay Output

1048

1049

1050

* Downlink Payload (prefix 0x03):

1051

1052

0x03 aa bb ~/~/ Set RO1/RO2 output

1053

1054

If payload = 0x030100, it means set RO1 to close and RO2 to open.

1055

1056

01: Close , 00: Open , 11: No action

1057

1058

|Downlink Code|RO1|RO2

1059

|03 00 11|Open|No Action

1060

|03 01 11|Close|No Action

1061

|03 11 00|No Action|Open

1062

|03 11 01|No Action|Close

1063

|03 00 00|Open|Open

1064

|03 01 01|Close|Close

|03 01 00|Close|Open

|03 00 01|Open|Close

Device will upload a packet if downlink code executes successfully.

1069

1070

1071

==== Relay ~-~- Control Relay Output RO1/RO2 with time control ====

* AT Command:

There is no AT Command to control Relay Output

1076

1077

1078

* Downlink Payload (prefix 0x05):

1079

1080

0x05 aa bb cc dd ~/~/ Set RO1/RO2 relay with time control:

1081

1082

This is to control the relay output time of relay. Include four bytes:

1083

1084

**First Byte:** Type code (0x05)

1085

1086

**Second Byte(aa)**: Inverter Mode

1087

1088

01: Relays will change back to original state after timeout.

1089

1090

00: Relays will change to an inverter state after timeout

1091

1092

1093

**Third Byte(bb)**: Control Method and Ports status:

1094

1095

|Value|Status

1096

|0x11|RO1 and RO2 to NO

1097

|0x10|RO2 to NO, RO1 to NC

1098

|0x01|RO2 to NC, RO1 to NO

1099

|0x00|RO1 and RO2 to NC.

1100

|0x20|RO1 No Action, RO2 to NC

1101

|0x21|RO1 No Action, RO2 to NO

1102

|0x02|RO1 to NC, RO2 No Action

1103

|0x12|RO1 to NO, RO2 No Action

1104

1105

1106

**Fourth / Fifth Bytes (cc)**: Latching time. Unit: ms

1107

1108

Device will upload a packet if downlink code executes successfully.

**Example payload:**

1. 05 01 11 07 D0

Relay1 and Relay 2 will be set to NO , last 2 seconds, then change back to original state.

1. 05 01 10 07 D0

Relay1 will change to NO, Relay2 will change to NC, last 2 seconds, then both change back to original state.

1. 05 00 01 07 D0

Relay1 will change to NC, Relay2 will change to NO, last 2 seconds, then relay change to NO, Relay2 change to NC.

1. 05 00 00 07 D0

Relay 1 & relay2 will change to NC, last 2 seconds, then both change to NO.

==== Counting ~-~- Voltage threshold counting ====

1139

1140

When voltage exceed the threshold, count. Feature see [[MOD4>>path:#MOD4]]

* AT Command:

AT+VOLMAX ~/~/ See [[MOD4>>path:#MOD4]]

1145

1146

1147

* Downlink Payload (prefix 0xA5):

1148

1149

0xA5 aa bb cc ~/~/ Same as AT+VOLMAX=(aa bb),cc

1150

1151

1152

==== Counting ~-~- Pre-configure the Count Number ====

* AT Command:

AT+SETCNT=aa,(bb cc dd ee)

aa: 1: Set count1,

2: Set count2,

3: Set AV1 count

Bb cc dd ee: number to be set

1165

1166

1167

* Downlink Payload (prefix 0xA8):

1168

1169

0x A8 aa bb cc dd ee ~/~/ same as AT+SETCNT=aa,(bb cc dd ee)

==== Counting ~-~- Clear Counting ====

1176

1177

Clear counting for counting mode

* AT Command:

AT+CLRCOUNT ~/~/ clear all counting

1182

1183

1184

* Downlink Payload (prefix 0xA6):

1185

1186

0x A6 01 ~/~/ clear all counting,

==== Counting ~-~- Change counting mode save time ====

* AT Command:

AT+COUTIME=60 ~/~/ Set save time to 60 seconds. Device will save the counting result in internal flash every 60 seconds. (min value: 30)

1196

1197

1198

* Downlink Payload (prefix 0xA7):

1199

1200

0x A7 aa bb cc ~/~/ same as AT+COUTIME =aa bb cc,

1201

1202

range: aa bb cc:0 to 16777215, (unit:second)

1.

11. Integrate with Mydevice

1209

1210

1211

Mydevices provides a human friendly interface to show the sensor data, once we have data in TTN, we can use Mydevices to connect to TTN and see the data in Mydevices. Below are the steps:

1212

1213

1214

Step 1: Be sure that your device is programmed and properly connected to the network at this time.

1215

1216

Step 2: To configure the Application to forward data to Mydevices you will need to add integration. To add the Mydevices integration, perform the following steps:

1217

1218

1219

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image010.png]]

1220

1221

1222

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image011.png]]

1223

1224

1225

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image012.png]]

Step 3: Create an account or log in Mydevices.

1230

1231

Step 4: Search LT-22222-L(for both LT-22222-L / LT-33222-L) and add DevEUI.

1232

1233

Search under The things network

1234

1235

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image013.png]]

1236

1237

1238

After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.

1239

1240

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]]

1241

1242

1243

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]

1244

1245

1246

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]]

1247

1248

1249

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]

1250

1251

1252

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image018.png]]

1.

11. Interface Detail

111. Digital Input Port: DI1/DI2 /DI3 ( For LT-33222-L, low active )

1258

1259

Support NPN Type sensor

1260

1261

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.png]]

1.

11.

111. Digital Input Port: DI1/DI2 ( For LT-22222-L)

1268

1269

The DI port of LT-22222-L can support NPN or PNP output sensor.

1270

1271

Internal circuit as below, the NEC2501 is a photocoupler, the Active current (from NEC2501 pin 1 to pin 2 is 1ma and the max current is 50mA. When there is active current pass NEC2501 pin1 to pin2. The DI will be active high

1272

1273

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]

1274

1275

When use need to connect a device to the DI port, both DI1+ and DI1- must be connected.

1276

1277

1278

**Example1**: Connect to a Low active sensor.

1279

1280

This type of sensor will output a low signal GND when active.

1281

1282

* Connect sensor’s output to DI1-

1283

* Connect sensor’s VCC to DI1+.

1284

1285

So when sensor active, the current between NEC2501 pin1 and pin2 is:

1286

1287

//IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]] = DI1+ / 1K.

1288

1289

If DI1+ = 12v, the //IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]] = 12mA , So the LT-22222-L will be able to detect this active signal.

1290

1291

1292

**Example2**: Connect to a High active sensor.

1293

1294

This type of sensor will output a high signal (example 24v) when active.

1295

1296

* Connect sensor’s output to DI1+

1297

* Connect sensor’s GND DI1-.

1298

1299

So when sensor active, the current between NEC2501 pin1 and pin2 is:

1300

1301

//IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]] = DI1+ / 1K.

1302

1303

If DI1+ = 24v, the //IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]] = 24mA , So the LT-22222-L will be able to detect this high active signal.

1304

1305

1306

**Example3**: Connect to a 220v high active sensor.公司测试一下

1307

1308

Assume user want to monitor an active signal higher than 220v, to make sure not burn the photocoupler

1309

1310

* Connect sensor’s output to DI1+ with a serial 50K resistor

1311

* Connect sensor’s GND DI1-.

1312

1313

So when sensor active, the current between NEC2501 pin1 and pin2 is:

1314

1315

//IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]] = DI1+ / 51K.

1316

1317

If sensor output is 220v, the //IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]] = 4.3mA , So the LT-22222-L will be able to detect this high active signal safely.

1.

11.

111. Digital Output Port: DO1/DO2 /DO3

1323

1324

NPN output: GND or Float. Max voltage can apply to output pin is 36v.

1325

1326

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

1.

11.

111. Analog Input Interface

1334

1335

The analog input interface is as below. The LT will measure the IN2 voltage so to calculate the current pass the Load. The formula is:

1336

1337

AC2 = (IN2 voltage )/12

1338

1339

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]

Example to connect a 4~~20mA sensor

1344

1345

We take the wind speed sensor as an example for reference only.

1346

1347

Specifications of the wind speed sensor:

Red:12~~24v

Yellow:4~~20mA

Black:GND

Connection diagram:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.jpg]]

1359

1360

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]

1.

11.

111. Relay Output

The LT serial controller has two relay interfaces; each interface uses two pins of the screw terminal. User can connect other device’s Power Line to in serial of RO1_1 and RO_2. Such as below:

1369

1370

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]

1371

1372

1373

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]

1.

11. LEDs Indicators

|**LEDs**|**Feature**

1384

|**PWR**|Always on if there is power

1385

|**SYS**|After device is powered on, the SYS will **fast blink in GREEN** for 5 times, means RS485-LN start to join LoRaWAN network. If join success, SYS will be **on GREEN for 5 seconds. **SYS will **blink Blue** on every upload and **blink Green** once receive a downlink message.

1386

|**TX**|(((

1387

Device boot: TX blinks 5 times.

1388

1389

Successful join network: TX ON for 5 seconds.

1390

1391

Transmit a LoRa packet: TX blinks once

1392

)))

1393

|**RX**|RX blinks once when receive a packet.

|**DO1**|

|**DO2**|

|**DO3**|

|**DI2**|(((

For LT-22222-L: ON when DI2 is high, LOW when DI2 is low

1399

1400

For LT-33222-L: ON when DI2 is low, LOW when DI2 is high

1401

)))

1402

|**DI2**|(((

1403

For LT-22222-L: ON when DI2 is high, LOW when DI2 is low

1404

1405

For LT-33222-L: ON when DI2 is low, LOW when DI2 is high

1406

)))

1407

|**DI3**|For LT-33222-L ONLY: ON when DI3 is low, LOW when DI3 is high

1408

|**DI2**|(((

1409

For LT-22222-L: ON when DI2 is high, LOW when DI2 is low

1410

1411

For LT-33222-L: ON when DI2 is low, LOW when DI2 is high

)))

|**RO1**|

|**RO2**|

1. Use AT Command

11. Access AT Command

1421

1422

LT supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to LT for using AT command, as below.

1423

1424

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

1425

1426

1427

In PC, User needs to set **serial tool**(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to **9600** to access to access serial console for LT. The AT commands are disable by default and need to enter password (default:**123456**) to active it. As shown below:

1428

1429

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

1430

1431

1432

More detail AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/]]

1433

1434

AT+<CMD>? : Help on <CMD>

AT+<CMD> : Run <CMD>

AT+<CMD>=<value> : Set the value

1439

1440

AT+<CMD>=? : Get the value

1441

1442

ATZ: Trig a reset of the MCU

1443

1444

AT+FDR: Reset Parameters to Factory Default, Keys Reserve

1445

1446

AT+DEUI: Get or Set the Device EUI

1447

1448

AT+DADDR: Get or Set the Device Address

1449

1450

AT+APPKEY: Get or Set the Application Key

1451

1452

AT+NWKSKEY: Get or Set the Network Session Key

1453

1454

AT+APPSKEY: Get or Set the Application Session Key

1455

1456

AT+APPEUI: Get or Set the Application EUI

1457

1458

AT+ADR: Get or Set the Adaptive Data Rate setting. (0: off, 1: on)

1459

1460

AT+TXP: Get or Set the Transmit Power (0-5, MAX:0, MIN:5, according to LoRaWAN Spec)

1461

1462

AT+DR: Get or Set the Data Rate. (0-7 corresponding to DR_X)

1463

1464

AT+DCS: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing

1465

1466

AT+PNM: Get or Set the public network mode. (0: off, 1: on)

1467

1468

AT+RX2FQ: Get or Set the Rx2 window frequency

1469

1470

AT+RX2DR: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)

1471

1472

AT+RX1DL: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms

1473

1474

AT+RX2DL: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms

1475

1476

AT+JN1DL: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms

1477

1478

AT+JN2DL: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms

1479

1480

AT+NJM: Get or Set the Network Join Mode. (0: ABP, 1: OTAA)

1481

1482

AT+NWKID: Get or Set the Network ID

1483

1484

AT+FCU: Get or Set the Frame Counter Uplink

1485

1486

AT+FCD: Get or Set the Frame Counter Downlink

1487

1488

AT+CLASS: Get or Set the Device Class

1489

1490

AT+JOIN: Join network

1491

1492

AT+NJS: Get OTAA Join Status

1493

1494

AT+SENDB: Send hexadecimal data along with the application port

1495

1496

AT+SEND: Send text data along with the application port

1497

1498

AT+RECVB: Print last received data in binary format (with hexadecimal values)

1499

1500

AT+RECV: Print last received data in raw format

1501

1502

AT+VER: Get current image version and Frequency Band

1503

1504

AT+CFM: Get or Set the confirmation mode (0-1)

1505

1506

AT+CFS: Get confirmation status of the last AT+SEND (0-1)

1507

1508

AT+SNR: Get the SNR of the last received packet

1509

1510

AT+RSSI: Get the RSSI of the last received packet

1511

1512

AT+TDC: Get or set the application data transmission interval in ms

1513

1514

AT+PORT: Get or set the application port

1515

1516

AT+DISAT: Disable AT commands

1517

1518

AT+PWORD: Set password, max 9 digits

1519

1520

AT+CHS: Get or Set Frequency (Unit: Hz) for Single Channel Mode

1521

1522

AT+CHE: Get or Set eight channels mode, Only for US915, AU915, CN470

1523

1524

AT+CFG: Print all settings

1.

11. Common AT Command Sequence

1530

111. Multi-channel ABP mode (Use with SX1301/LG308)

1531

1532

If device has not joined network yet:

123456

AT+FDR

123456

AT+NJM=0

ATZ

If device already joined network:

AT+NJM=0

ATZ

1.

11.

111. Single-channel ABP mode (Use with LG01/LG02)

1554

1555

123456 Enter Password to have AT access.

1556

1557

AT+FDR Reset Parameters to Factory Default, Keys Reserve

1558

1559

123456 Enter Password to have AT access.

1560

1561

AT+CLASS=C Set to work in CLASS C

1562

1563

AT+NJM=0 Set to ABP mode

1564

1565

AT+ADR=0 Set the Adaptive Data Rate Off

1566

1567

AT+DR=5 Set Data Rate

1568

1569

AT+TDC=60000 Set transmit interval to 60 seconds

1570

1571

AT+CHS=868400000 Set transmit frequency to 868.4Mhz

1572

1573

AT+RX2FQ=868400000 Set RX2Frequency to 868.4Mhz (according to the result from server)

1574

1575

AT+RX2DR=5 Set RX2DR to match the downlink DR from server. see below

1576

1577

AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1, this ID can be found in the LoRa Server portal.

ATZ Reset MCU

**Note:**

1. Make sure the device is set to ABP mode in the IoT Server.

1584

1. Make sure the LG01/02 gateway RX frequency is exactly the same as AT+CHS setting.

1585

1. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.

1586

1. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5

1587

1588

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]]

1.

11.

111. Change to Class A

If sensor JOINED

AT+CLASS=A

ATZ

1. FAQ

1.

11. How to upgrade the image?

1611

1612

The LT LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to LT to:

1613

1614

* Support new features

1615

* For bug fix

1616

* Change LoRaWAN bands.

1617

1618

1619

Below shows the hardware connection for how to upload an image to the LT:

1620

1621

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

1622

1623

1624

**Step1:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].

1625

1626

**Step2**: Download the [[LT Image files>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]].

1627

1628

**Step3: **Open flashloader; choose the correct COM port to update.

**For LT-33222-L**:

Hold down the PRO button and then momentarily press the RST reset button and the **DO2 led** will change from OFF to ON. When **DO2 LED** is on, it means the device is in download mode.

**For LT-22222-L**:

Hold down the PRO button and then momentarily press the RST reset button and the **DO1 led** will change from OFF to ON. When **DO1 LED** is on, it means the device is in download mode.

|(((

Board detected

)))

|(((

)))

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]]

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]]

1653

1654

1655

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image037.png]]

1656

1657

1658

**Notice**: In case user has lost the program cable. User can hand made one from a 3.5mm cable. The pin mapping is:

1659

1660

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image038.png]]

1.

11. How to change the LoRa Frequency Bands/Region?

1665

1666

User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.

1.

11. How to set up LT to work with Single Channel Gateway such as LG01/LG02?

1671

1672

In this case, users need to set LT-33222-L to work in ABP mode & transmit in only one frequency.

1673

1674

Assume we have a LG02 working in the frequency 868400000 now , below is the step.

1675

1676

1677

**Step1**: Log in TTN, Create an ABP device in the application and input the network session key (NETSKEY), app session key (APPSKEY) from the device.

1678

1679

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image039.png]]

1680

1681

Note: user just need to make sure above three keys match, User can change either in TTN or Device to make then match. In TTN, NETSKEY and APPSKEY can be configured by user in setting page, but Device Addr is generated by TTN.

1682

1683

1684

**Step2: **Run AT Command to make LT work in Single frequency & ABP mode. Below is the AT commands:

1685

1686

123456 Enter Password to have AT access.

1687

1688

AT+FDR Reset Parameters to Factory Default, Keys Reserve

1689

1690

123456 Enter Password to have AT access.

1691

1692

AT+NJM=0 Set to ABP mode

1693

1694

AT+ADR=0 Set the Adaptive Data Rate Off

1695

1696

AT+DR=5 Set Data Rate (Set AT+DR=3 for 915 band)

1697

1698

AT+TDC=60000 Set transmit interval to 60 seconds

1699

1700

AT+CHS=868400000 Set transmit frequency to 868.4Mhz

1701

1702

AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1

ATZ Reset MCU

As shown in below:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image040.png]]

1.

11. Can I see counting event in Serial?

1714

1715

User can run AT+DEBUG command to see the counting event in serial. If firmware too old and doesn’t support AT+DEBUG. User can update to latest firmware first.

1. Trouble Shooting

11. Downlink doesn’t work, how to solve it?

1722

1723

Please see this link for how to debug:

1724

1725

[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#How_it_work>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#How_it_work]]

1.

11. Have trouble to upload image.

1730

1731

See this link for trouble shooting:

1732

1733

[[http:~~/~~/wiki.dragino.com/index.php?title=Firmware_Upgrade_Trouble_Shooting#UART_upgrade_trouble_shooting>>url:http://wiki.dragino.com/index.php?title=Firmware_Upgrade_Trouble_Shooting#UART_upgrade_trouble_shooting]]

1.

11. Why I can’t join TTN in US915 /AU915 bands?

1738

1739

It might be about the channels mapping. Please see this link for detail:

1740

1741

[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band]]

1. Order Info

**For LT-33222-L-XXX or LT-22222-L-XXX:**

**XXX:**

* **EU433**: LT with frequency bands EU433

1754

* **EU868**: LT with frequency bands EU868

1755

* **KR920**: LT with frequency bands KR920

1756

* **CN470**: LT with frequency bands CN470

1757

* **AS923**: LT with frequency bands AS923

1758

* **AU915**: LT with frequency bands AU915

1759

* **US915**: LT with frequency bands US915

1760

* **IN865**: LT with frequency bands IN865

1761

* **CN779**: LT with frequency bands CN779

1. Packing Info

**Package Includes**:

1767

1768

* LT I/O Controller x 1

1769

* Stick Antenna for LoRa RF part x 1

1770

* Bracket for controller x1

* Program cable x 1

**Dimension and weight**:

1775

1776

* Device Size: 13.5 x 7 x 3 cm

1777

* Device Weight: 105g

1778

* Package Size / pcs : 14.5 x 8 x 5 cm

1779

* Weight / pcs : 170g

1. Support

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1785

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to

1786

1787

[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]

Wiki source code of LT-22222-L LoRa IO Controller User Manual

Applications

Navigation