Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -435,7 +435,6 @@
435	435	* Reply to non-confirmed packet: 14 00
436	436
437	437
438		-
439	439	== 2.8 Frequency Plans ==
440	440
441	441	(((
...	...	@@ -492,7 +492,6 @@
492	492	* Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
493	493
494	494
495		-
496	496	=== 2.8.3 CN470-510 (CN470) ===
497	497
498	498	Used in China, Default use CHE=1
...	...	@@ -561,7 +561,6 @@
561	561
562	562
563	563
564		-
565	565	=== 2.8.5 AS920-923 & AS923-925 (AS923) ===
566	566
567	567	(% style="color:blue" %)**Default Uplink channel:**
...	...	@@ -677,7 +677,6 @@
677	677
678	678
679	679
680		-
681	681	== 2.10 ​Firmware Change Log ==
682	682
683	683
...	...	@@ -746,7 +746,6 @@
746	746	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
747	747	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
748	748
749		-
750	750	== 3.2 Set Interrupt Mode ==
751	751
752	752	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -765,7 +765,6 @@
765	765	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
766	766	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
767	767
768		-
769	769	== 3.3 Calibrate Sensor ==
770	770
771	771	Detail See [[Calibration Guide>>||anchor="2.7Calibration"]] for the user of 0x13 and 0x14 downlink commands
...	...	@@ -784,7 +784,6 @@
784	784	* Reply to non-confirmed packet: 26 00
785	785
786	786
787		-
788	788	Device will send an uplink after got this downlink command. With below payload:
789	789
790	790	Configures info payload:
...	...	@@ -913,32 +913,34 @@
913	913
914	914	And the Life expectation in difference case will be shown on the right.
915	915
916		-[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]
	909	+[[image:1654588577573-122.png]]
917	917
918	918
919	919	The battery related documents as below:
920	920
921		-* [[Battery Dimension>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]],
922		-* [[Lithium-Thionyl Chloride Battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]] datasheet
923		-* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
924		-
925		-|(((
926		-JST-XH-2P connector
	914	+* (((
	915	+[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
927	927	)))
	917	+* (((
	918	+[[Lithium-Thionyl Chloride Battery  datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
	919	+)))
	920	+* (((
	921	+[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
	922	+)))
928	928
929		-[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]
	924	+[[image:image-20220607155856-8.png]]
930	930
931	931
932	932
933	933	1.
934		-11.
	929	+11.
935	935	111. ​Battery Note
936	936
937	937	The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
938	938
939	939
940		-1.
941		-11.
	935	+1.
	936	+11.
942	942	111. ​Replace the battery
943	943
944	944	You can change the battery in the LSPH01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.