Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -556,7 +556,6 @@
556	556	* Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
557	557
558	558
559		-
560	560	=== 2.8.5 AS920-923 & AS923-925 (AS923) ===
561	561
562	562	(% style="color:blue" %)**Default Uplink channel:**
...	...	@@ -739,6 +739,7 @@
739	739	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
740	740
741	741
	741	+
742	742	== 3.2 Set Interrupt Mode ==
743	743
744	744	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -745,24 +745,9 @@
745	745
746	746	(% style="color:#037691" %)**AT Command: AT+INTMOD**
747	747
748		-(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:709px" %)
749		-|=(% style="width: 163px;" %)**Command Example**|=(% style="width: 304px;" %)**Function**|=(% style="width: 239px;" %)**Response**
750		-|(% style="width:163px" %)AT+INTMOD=?|(% style="width:304px" %)Show current interrupt mode|(% style="width:239px" %)(((
751		-0
	748	+[[image:image-20220607153759-6.png]]
752	752
753		-OK
754	754
755		-the mode is 0 = No interruption
756		-)))
757		-|(% style="width:163px" %)AT+INTMOD=2|(% style="width:304px" %)(((
758		-Set Transmit Interval
759		-
760		-1. (Disable Interrupt),
761		-1. (Trigger by rising and falling edge),
762		-1. (Trigger by falling edge)
763		-1. (Trigger by rising edge)
764		-)))|(% style="width:239px" %)OK
765		-
766	766	(% style="color:#037691" %)**Downlink Command: 0x06**
767	767
768	768	Format: Command Code (0x06) followed by 3 bytes.
...	...	@@ -772,16 +772,15 @@
772	772	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
773	773	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
774	774
775		-
776	776	== 3.3 Calibrate Sensor ==
777	777
778		-Detail See [[Calibration Guide>>path:#Calibration]] for the user of 0x13 and 0x14 downlink commands
	762	+Detail See [[Calibration Guide>>||anchor="2.7Calibration"]] for the user of 0x13 and 0x14 downlink commands
779	779
780	780
781	781
782		-1.
783		-11. Get Firmware Version Info
784	784
	767	+== 3.4 Get Firmware Version Info ==
	768	+
785	785	Feature: use downlink to get firmware version.
786	786
787	787
...	...	@@ -888,7 +888,7 @@
888	888	LSPH01:  2.45v ~~ 3.6v
889	889
890	890
891		-1.
	875	+1.
892	892	11. Replace Battery
893	893
894	894	Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.
...	...	@@ -897,7 +897,7 @@
897	897
898	898
899	899
900		-1.
	884	+1.
901	901	11. Power Consumption Analyze
902	902
903	903	Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
...	...	@@ -937,14 +937,14 @@
937	937
938	938
939	939	1.
940		-11.
	924	+11.
941	941	111. ​Battery Note
942	942
943	943	The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
944	944
945	945
946		-1.
947		-11.
	930	+1.
	931	+11.
948	948	111. ​Replace the battery
949	949
950	950	You can change the battery in the LSPH01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.