Changes for page LLMS01-LoRaWAN Leaf Moisture Sensor User Manual

Last modified by Bei Jinggeng on 2024/03/30 17:55

From version < 24.2 >

edited by Xiaoling
on 2022/06/07 14:46

To version < 24.1 >

edited by Xiaoling
on 2022/06/07 14:42

Change comment: Uploaded new attachment "1654584128046-287.png", version {1}

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -55,6 +55,7 @@
  * IP68 rate for the Sensor Probe
  * 8500mAh Battery for long term use
++
  == 1.3 Probe Specification ==
@@ -75,10 +75,12 @@
  * IP68 Protection
  * Length: 3.5 meters
++
  == 1.4 Applications ==
  * Smart Agriculture
++
  == 1.5 Pin mapping and power on ==
  [[image:1654580482666-473.png]]
@@ -265,6 +265,7 @@
  |0x02|Reply configures info|[[Configure Info Payload>>||anchor="H3.4GetFirmwareVersionInfo"]]
  |0x03|Reply Calibration Info|[[Calibration Payload>>||anchor="H2.7Calibration"]]
++
  === 2.3.7 Decode payload in The Things Network ===
  While using TTN network, you can add the payload format to decode the payload.
@@ -340,65 +340,55 @@
--== 2.6 Installation and Maintain ==
++1.
++11. Installation and Maintain
++111. Before measurement
--=== 2.6.1 Before measurement ===
--
--(((
  If the LSPH01 has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy.
--)))
++1.
++11.
++111. Measurement
--=== 2.6.2 Measurement ===
++**Measurement the soil surface**
--(% style="color:#4f81bd" %)**Measurement the soil surface:**
++[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]] Choose the proper measuring position. Split the surface soil according to the measured deep.
--[[image:1654584128046-287.png]]
--Choose the proper measuring position. Split the surface soil according to the measured deep.
--
  Put pure water, or rainwater to make the soil of measurement point to moist mud. Remove rocks or hard things.
++
  Slowly insert the probe to the measure point. Don’t use large force which will break the probe. Make sure not shake when inserting.
++
  Put soil over the probe after insert. And start to measure.
--(% style="color:#4f81bd" %)**Measurement inside soil:**
++**Measurement inside soil**
--Dig a hole with diameter > 20CM.
--Insert the probe inside, method like measure the surface.
++Dig a hole with diameter > 20CM.
--=== 2.6.3 Maintain Probe ===
++Insert the probe inside, method like measure the surface.
--1. (((
--pH probe electrode is fragile and no strong. User must avoid strong force or hitting it.
--)))
--1. (((
--After long time use (3~~ 6  months). The probe electrode needs to be clean; user can use high grade sandpaper to polish it or put in 5% hydrochloric acid for several minutes. After the metal probe looks like new, user can use pure water to wash it.
--)))
--1. (((
--Probe reference electrode is also no strong, need to avoid strong force or hitting.
--)))
--1. (((
--User should keep reference electrode wet while not use.
--)))
--1. (((
--Avoid the probes to touch oily matter. Which will cause issue in accuracy.
--)))
--1. (((
--The probe is IP68 can be put in water.
--)))
++1.
++11.
++111. Maintain Probe
++1111. pH probe electrode is fragile and no strong. User must avoid strong force or hitting it.
++1111. After long time use (3~~ 6  months). The probe electrode needs to be clean; user can use high grade sandpaper to polish it or put in 5% hydrochloric acid for several minutes. After the metal probe looks like new, user can use pure water to wash it.
++1111. Probe reference electrode is also no strong, need to avoid strong force or hitting.
++1111. User should keep reference electrode wet while not use.
++1111. Avoid the probes to touch oily matter. Which will cause issue in accuracy.
++1111. The probe is IP68 can be put in water.
++1.
++11. Calibration
--2.7 Calibration
--
  User can do calibration for the probe. It is limited to use below pH buffer solution to calibrate: 4.00, 6.86, 9.18. When calibration, user need to clean the electrode and put the probe in the pH buffer solution to wait the value stable ( a new clean electrode might need max 24 hours to be stable).
@@ -467,13 +467,13 @@
  * Reply to the confirmation package: 14 01
  * Reply to non-confirmed packet: 14 00
--1.
++1.
 . Frequency Plans
  The LSPH01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
--1.
--11.
++1.
++11.
 . EU863-870 (EU868)
  Uplink:
@@ -504,8 +504,8 @@
 .525 - SF9BW125 (RX2 downlink only)
--1.
--11.
++1.
++11.
 . US902-928(US915)
  Used in USA, Canada and South America. Frequency band as per definition in LoRaWAN 1.0.3 Regional document.
@@ -519,8 +519,8 @@
  * Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
  * Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
--1.
--11.
++1.
++11.
 . CN470-510 (CN470)
  Used in China, Default use CHE=1
@@ -565,8 +565,8 @@
 .3 - SF12BW125 (RX2 downlink only)
--1.
--11.
++1.
++11.
 . AU915-928(AU915)
  Frequency band as per definition in LoRaWAN 1.0.3 Regional document.
@@ -580,8 +580,8 @@
  * Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
  * Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
--1.
--11.
++1.
++11.
 . AS920-923 & AS923-925 (AS923)
  **Default Uplink channel:**
@@ -633,8 +633,8 @@
 .2 - SF10BW125 (RX2)
--1.
--11.
++1.
++11.
 . KR920-923 (KR920)
  Default channel:
@@ -670,8 +670,8 @@
 .9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
--1.
--11.
++1.
++11.
 . IN865-867 (IN865)
  Uplink:
@@ -690,7 +690,7 @@
 .550 - SF10BW125 (RX2)
--1.
++1.
 . LED Indicator
  The LSPH01 has an internal LED which is to show the status of different state.
@@ -699,7 +699,7 @@
  * The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
  * Blink once when device transmit a packet.
--1.
++1.
 . Firmware Change Log
  **Firmware download link:**
@@ -745,7 +745,7 @@
  These commands only valid for LSPH01, as below:
--1.
++1.
 . Set Transmit Interval Time
  Feature: Change LoRaWAN End Node Transmit Interval.
@@ -775,7 +775,7 @@
  * Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
  * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
--1.
++1.
 . Set Interrupt Mode
  Feature, Set Interrupt mode for GPIO_EXIT.
@@ -808,7 +808,7 @@
  * Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
  * Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
--1.
++1.
 . Calibrate Sensor
  Detail See [[Calibration Guide>>path:#Calibration]] for the user of 0x13 and 0x14 downlink commands
@@ -815,7 +815,7 @@
--1.
++1.
 . Get Firmware Version Info
  Feature: use downlink to get firmware version.
@@ -924,7 +924,7 @@
  LSPH01:  2.45v ~~ 3.6v
--1.
++1.
 . Replace Battery
  Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.
@@ -933,7 +933,7 @@
--1.
++1.
 . Power Consumption Analyze
  Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
@@ -973,14 +973,14 @@
 .
--11.
++11.
 . Battery Note
  The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
--1.
--11.
++1.
++11.
 . Replace the battery
  You can change the battery in the LSPH01.The type of battery is not limited as long as the output is between 3v to 3.6v.  On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.

Changes for page LLMS01-LoRaWAN Leaf Moisture Sensor User Manual

Summary

Details

Applications

Navigation