PS-LB -- LoRaWAN Air Water Pressure Sensor User Manual

The Dragino PS-LB series sensors are **LoRaWAN Pressure Sensor** for Internet of Things solution. PS-LB can measure Air, Water pressure and liquid level and upload the sensor data via wireless to LoRaWAN IoT server.

27

28

The PS-LB series sensors include **Thread Installation Type** and **Immersion Type**, it supports different pressure range which can be used for different measurement requirement.

29

30

The LoRa wireless technology used in PS-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.

31

32

PS-LB supports BLE configure and wireless OTA update which make user easy to use.

33

34

PS-LB is powered by **8500mAh Li-SOCI2 battery**, it is designed for long term use up to 5 years.

35

36

Each PS-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.

37

38

[[image:1675071321348-194.png]]

== 1.2 Features ==

* LoRaWAN 1.0.3 Class A

46

* Ultra-low power consumption

47

* Measure air / gas or water pressure

48

* Different pressure range available

49

* Thread Installation Type or Immersion Type

50

* Monitor Battery Level

51

* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865

52

* Support Bluetooth v5.1 and LoRaWAN remote configure

53

* Support wireless OTA update firmware

54

* Uplink on periodically

55

* Downlink to change configure

56

* 8500mAh Battery for long term use

57

58

59

== 1.3 Specification ==

60

61

62

**Micro Controller:**

* MCU: 48Mhz ARM

* Flash: 256KB

* RAM: 64KB

**Common DC Characteristics:**

69

70

* Supply Voltage: 2.5v ~~ 3.6v

71

* Operating Temperature: -40 ~~ 85°C

**LoRa Spec:**

* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz

76

* Max +22 dBm constant RF output vs.

77

* RX sensitivity: down to -139 dBm.

78

* Excellent blocking immunity

79

80

**Current Input Measuring :**

* Range: 0 ~~ 20mA

* Accuracy: 0.02mA

* Resolution: 0.001mA

85

86

**Voltage Input Measuring:**

* Range: 0 ~~ 30v

* Accuracy: 0.02v

* Resolution: 0.001v

**Battery:**

* Li/SOCI2 un-chargeable battery

95

* Capacity: 8500mAh

96

* Self-Discharge: <1% / Year @ 25°C

97

* Max continuously current: 130mA

98

* Max boost current: 2A, 1 second

99

100

**Power Consumption**

101

102

* Sleep Mode: 5uA @ 3.3v

103

* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm

104

105

106

== 1.4 Probe Types ==

107

108

=== 1.4.1 Thread Installation Type ===

109

110

111

[[image:1675071448299-229.png]]

112

113

* Hersman Pressure Transmitter

114

* Measuring Range: -0.1 ~~ 0 ~~ 60MPa, see order info.

115

* Accuracy: 0.2% F.S

116

* Long-Term Stability: 0.2% F.S ±0.05%

117

* Overload 200% F.S

118

* Zero Temperature Drift: 0.03% FS/℃(≤100Kpa), 0.02%FS/℃(＞100Kpa)

119

* FS Temperature Drift: 0.003% FS/℃(≤100Kpa), 0.002%FS/℃(＞100Kpa)

120

* Storage temperature: -30℃~~80℃

121

* Operating temperature: -20℃~~60℃

122

* Connector Type: Various Types, see order info

123

124

125

=== 1.4.2 Immersion Type ===

126

127

128

[[image:1675071521308-426.png]]

129

130

* Immersion Type, Probe IP Level: IP68

131

* Measuring Range: Measure range can be customized, up to 100m.

132

* Accuracy: 0.2% F.S

133

* Long-Term Stability: ±0.2% F.S / Year

134

* Overload 200% F.S

135

* Zero Temperature Drift: ±2% F.S)

136

* FS Temperature Drift: ±2% F.S

137

* Storage temperature: -30℃~~80℃

138

* Operating temperature: -40℃~~85℃

139

* Material: 316 stainless steels

140

141

142

== 1.5 Probe Dimension ==

== 1.6 Application and Installation ==

148

149

=== 1.6.1 Thread Installation Type ===

**Application:**

* Hydraulic Pressure

* Petrochemical Industry

156

* Health and Medical

157

* Food & Beverage Processing

158

* Auto-controlling house

159

* Constant Pressure Water Supply

160

* Liquid Pressure measuring

161

162

Order the suitable thread size and install to measure the air / liquid pressure

163

164

[[image:1675071670469-145.png]]

165

166

167

=== 1.6.2 Immersion Type ===

**Application:**

Liquid & Water Pressure / Level detect.

173

174

[[image:1675071725288-579.png]]

175

176

177

The Immersion Type pressure sensor is shipped with the probe and device separately. When user got the device, below is the wiring to for connect the probe to the device.

178

179

180

[[image:1675071736646-450.png]]

181

182

183

[[image:1675071776102-240.png]]

184

185

186

== 1.7 Sleep mode and working mode ==

187

188

189

**Deep Sleep Mode: **Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.

190

191

**Working Mode:** In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.

192

193

194

== 1.8 Button & LEDs ==

195

196

197

[[image:1675071855856-879.png]]

198

199

200

(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)

201

|(% style="width:138px" %)**Behavior on ACT**|(% style="width:100px" %)**Function**|**Action**

202

|(% style="width:138px" %)Pressing ACT between 1s < time < 3s|(% style="width:100px" %)Send an uplink|(((

203

If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, **blue led** will blink once.

204

205

Meanwhile, BLE module will be active and user can connect via BLE to configure device.

206

)))

207

|(% style="width:138px" %)Pressing ACT for more than 3s|(% style="width:100px" %)Active Device|(((

208

**Green led** will fast blink 5 times, device will enter **OTA mode** for 3 seconds. And then start to JOIN LoRaWAN network.

209

210

**Green led** will solidly turn on for 5 seconds after joined in network.

211

212

Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.

213

)))

214

|(% style="width:138px" %)Fast press ACT 5 times.|(% style="width:100px" %)Deactivate Device|red led will solid on for 5 seconds. Means PS-LB is in Deep Sleep Mode.

== 1.9 Pin Mapping ==

219

220

221

[[image:1675072568006-274.png]]

222

223

224

== 1.10 BLE connection ==

225

226

227

PS-LB support BLE remote configure.

228

229

230

BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:

231

232

* Press button to send an uplink

233

* Press button to active device.

234

* Device Power on or reset.

235

236

If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.

237

238

239

== 1.11 Mechanical ==

[[image:1675143884058-338.png]]

245

246

247

[[image:1675143899218-599.png]]

248

249

250

[[image:1675143909447-639.png]]

251

252

253

= 2. Configure PS-LB to connect to LoRaWAN network =

254

255

== 2.1 How it works ==

256

257

258

The PS-LB is configured as **LoRaWAN OTAA Class A** mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and activate the PS-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.

== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==

263

264

265

Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.

266

267

268

[[image:1675144005218-297.png]]

269

270

271

The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.

272

273

274

**Step 1**: Create a device in TTN with the OTAA keys from PS-LB.

275

276

Each PS-LB is shipped with a sticker with the default device EUI as below:

277

278

[[image:image-20230131134744-2.jpeg]]

You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:

283

284

285

**Register the device**

286

287

[[image:1675144099263-405.png]]

288

289

290

**Add APP EUI and DEV EUI**

291

292

[[image:1675144117571-832.png]]

293

294

295

**Add APP EUI in the application**

296

297

298

[[image:1675144143021-195.png]]

**Add APP KEY**

[[image:1675144157838-392.png]]

304

305

**Step 2**: Activate on PS-LB

306

307

308

Press the button for 5 seconds to activate the PS-LB.

309

310

**Green led** will fast blink 5 times, device will enter **OTA mode** for 3 seconds. And then start to JOIN LoRaWAN network. **Green led** will solidly turn on for 5 seconds after joined in network.

311

312

After join success, it will start to upload messages to TTN and you can see the messages in the panel.

== 2.3 Uplink Payload ==

317

318

319

Uplink payloads have two types:

320

321

* Distance Value: Use FPORT=2

322

* Other control commands: Use other FPORT fields.

323

324

The application server should parse the correct value based on FPORT settings.

325

326

327

=== 2.3.1 Device Status, FPORT~=5 ===

328

329

330

Include device configure status. Once PS-LB Joined the network, it will uplink this message to the server.

331

332

Users can also use the downlink command(0x26 01) to ask PS-LB to resend this uplink.

333

334

335

(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)

336

|(% colspan="6" %)**Device Status (FPORT=5)**

337

|(% style="width:103px" %)**Size (bytes)**|(% style="width:72px" %)**1**|**2**|**1**|**1**|**2**

338

339

340

Example parse in TTNv3

341

342

[[image:1675144504430-490.png]]

343

344

345

**Sensor Model**: For PS-LB, this value is 0x16

346

347

**Firmware Version**: 0x0100, Means: v1.0.0 version

**Frequency Band**:

*0x01: EU868

*0x02: US915

*0x03: IN865

*0x04: AU915

*0x05: KZ865

*0x06: RU864

*0x07: AS923

*0x08: AS923-1

*0x09: AS923-2

*0x0a: AS923-3

*0x0b: CN470

*0x0c: EU433

*0x0d: KR920

*0x0e: MA869

**Sub-Band**:

AU915 and US915:value 0x00 ~~ 0x08

383

384

CN470: value 0x0B ~~ 0x0C

385

386

Other Bands: Always 0x00

**Battery Info**:

Check the battery voltage.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

=== 1.3.2 Sensor value, FPORT~=2 ===

399

400

401

Uplink payload includes in total 9 bytes.

402

403

404

(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)

|(((

**Size**

**(bytes)**

)))|**2**|**2**|**2**|**2**|**1**

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]

1.

11.

111. Battery Info

Check the battery voltage for PS-LB.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

1.

11.

111. Probe Model

PS-LB has different kind of probe, 0~~20mA represent the full scale of the measuring range. So a 15mA output means different meaning for different probe.

For example.

|**Part Number**|**Probe Used**|**0~~20mA scale**|**Example: 10mA meaning**

441

|PS-LB-I3|immersion type with 3 meters cable|0~~3 meters|1.5 meters pure water

442

|PS-LB-I5|immersion type with 5 meters cable|0~~5 meters|2.5 meters pure water

443

444

The probe model field provides the convenient for server to identical how it should parse the 0~~20mA sensor value and get the correct value.

1.

11.

111. 0~~20mA value (IDC_IN)

450

451

The output value from Pressure Probe, use together with Probe Model to get the pressure value or water level.

**Example**:

27AE(H) = 10158 (D)/1000 = 10.158mA.

1.

11.

111. 0~~30V value ( pin VDC_IN)

462

463

Measure the voltage value. The range is 0 to 30V.

**Example**:

138E(H) = 5006(D)/1000= 5.006V

1.

11.

111. IN1&IN2&INT pin

IN1 and IN2 are used as digital input pins.

**Example**:

09 (H) :(0x09&0x08)>>3=1 IN1 pin is high level.

480

481

09 (H) :(0x09&0x04)>>2=0 IN2 pin is low level.

This data field shows if this packet is generated by **Interrupt Pin** or not. [[Click here>>path:#Int_mod]] for the hardware and software set up. Note: The Internet Pin is a separate pin in the screw terminal.

**Example:**

09 (H) : (0x09&0x02)>>1=1 The level of the interrupt pin.

491

492

09 (H) : 0x09&0x01=1 0x00: Normal uplink packet.

493

494

0x01: Interrupt Uplink Packet.

1.

11.

111. Decode payload in The Things Network

505

506

While using TTN network, you can add the payload format to decode the payload.

507

508

509

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]]

510

511

PS-LB TTN Payload Decoder:

512

513

[[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]

1.

11. Uplink Interval

The PS-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link:

520

521

[[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval]]

1.

11. Show Data in DataCake IoT Server

527

528

[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:

529

530

531

**Step 1**: Be sure that your device is programmed and properly connected to the network at this time.

532

533

**Step 2**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:

534

535

536

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

537

538

539

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]

540

541

542

Step 3: Create an account or log in Datacake.

543

544

Step 4: Create PS-LB product.

545

546

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]

551

552

553

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]

554

555

556

Step 5: add payload decode

557

558

559

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]

560

561

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

After added, the sensor data arrive TTN, it will also arrive and show in Datacake.

566

567

568

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

1.

11. Frequency Plans

The PS-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.

590

591

592

[[https:~~/~~/wiki.dragino.com/index.php?title=End_Device_Frequency_Band>>url:https://wiki.dragino.com/index.php?title=End_Device_Frequency_Band]]

1.

11. Firmware Change Log

599

600

**Firmware download link:**

601

602

[[https:~~/~~/www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0>>url:https://www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0]]

1. Configure PS-LB via AT Command or LoRaWAN Downlink

607

608

Use can configure PS-LB via AT Command or LoRaWAN Downlink.

609

610

* AT Command Connection: See [[FAQ>>path:#AT_COMMAND]].

611

* LoRaWAN Downlink instruction for different platforms:

612

613

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#Use_Note_for_Server>>url:http://wiki.dragino.com/index.php?title=Main_Page#Use_Note_for_Server]]

614

615

616

There are two kinds of commands to configure PS-LB, they are:

617

618

* **General Commands**.

619

620

These commands are to configure:

621

622

* General system settings like: uplink interval.

623

* LoRaWAN protocol & radio related command.

624

625

They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:

626

627

[[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_Downlink_Command>>url:http://wiki.dragino.com/index.php?title=End_Device_Downlink_Command]]

628

629

630

* **Commands special design for PS-LB**

631

632

These commands only valid for PS-LB, as below:

1.

11. Set Transmit Interval Time

637

638

Feature: Change LoRaWAN End Node Transmit Interval.

639

640

**AT Command: AT+TDC**

641

642

|**Command Example**|**Function**|**Response**

643

|AT+TDC=?|Show current transmit Interval|(((

30000

OK

the interval is 30000ms = 30s

649

)))

650

|AT+TDC=60000|Set Transmit Interval|(((

651

OK

652

653

Set transmit interval to 60000ms = 60 seconds

654

)))

655

656

**Downlink Command: 0x01**

657

658

Format: Command Code (0x01) followed by 3 bytes time value.

659

660

If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.

661

662

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

663

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

1.

11. Set Interrupt Mode

668

669

Feature, Set Interrupt mode for GPIO_EXIT.

670

671

**AT Command: AT+INTMOD**

672

673

|**Command Example**|**Function**|**Response**

674

|AT+INTMOD=?|Show current interrupt mode|(((

0

OK

the mode is 0 = No interruption

680

)))

681

|AT+INTMOD=2|(((

682

Set Transmit Interval

683

684

1. (Disable Interrupt),

685

1. (Trigger by rising and falling edge),

686

1. (Trigger by falling edge)

687

1. (Trigger by rising edge)

688

)))|OK

689

690

**Downlink Command: 0x06**

691

692

Format: Command Code (0x06) followed by 3 bytes.

693

694

This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.

695

696

* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode

697

* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger

698

699

1.

700

11. Set the output time

701

702

Feature, Control the output 3V3 , 5V or 12V.

703

704

**AT Command: AT+3V3T**

705

706

|**Command Example**|**Function**|**Response**

707

|AT+3V3T=?|Show 3V3 open time.|(((

0

OK

)))

|AT+3V3T=0|Normally open 3V3 power supply.|(((

OK

default setting

)))

|AT+3V3T=1000|Close after a delay of 1000 milliseconds.|(((

OK

)))

|AT+3V3T=65535|Normally closed 3V3 power supply.|(((

OK

)))

**AT Command: AT+5VT**

729

730

|**Command Example**|**Function**|**Response**

731

|AT+5VT=?|Show 5V open time.|(((

0

OK

)))

|AT+5VT=0|Normally closed 5V power supply.|(((

OK

default setting

)))

|AT+5VT=1000|Close after a delay of 1000 milliseconds.|(((

OK

)))

|AT+5VT=65535|Normally open 5V power supply.|(((

OK

)))

**AT Command: AT+12VT**

753

754

|**Command Example**|**Function**|**Response**

755

|AT+12VT=?|Show 12V open time.|(((

0

OK

)))

|AT+12VT=0|Normally closed 12V power supply.|OK

761

|AT+12VT=500|Close after a delay of 500 milliseconds.|(((

OK

)))

**Downlink Command: 0x07**

768

769

Format: Command Code (0x07) followed by 3 bytes.

770

771

The first byte is which power, the second and third bytes are the time to turn on.

772

773

* Example 1: Downlink Payload: 070101F4 -> AT+3V3T=500

774

* Example 2: Downlink Payload: 0701FFFF -> AT+3V3T=65535

775

* Example 3: Downlink Payload: 070203E8 -> AT+5VT=1000

776

* Example 4: Downlink Payload: 07020000 -> AT+5VT=0

777

* Example 5: Downlink Payload: 070301F4 -> AT+12VT=500

778

* Example 6: Downlink Payload: 07030000 -> AT+12VT=0

779

780

1.

781

11. Set the Probe Model

782

783

**AT Command: AT** **+PROBE**

784

785

|**Command Example**|**Function**|**Response**

786

|AT +PROBE =?|Get or Set the probe model.|(((

0

OK

)))

|AT +PROBE =0003|Set water depth sensor mode, 3m type.|OK

792

|AT +PROBE =0101|Set pressure transmitters mode, first type.|(((

OK

)))

|AT +PROBE =0000|Initial state, no settings.|(((

OK

)))

**Downlink Command: 0x08**

804

805

Format: Command Code (0x08) followed by 2 bytes.

806

807

* Example 1: Downlink Payload: 080003 -> AT+PROBE=0003

808

* Example 2: Downlink Payload: 080101 -> AT+PROBE=0101

1. Battery & how to replace

813

11. Battery Type

814

815

PS-LB is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.

816

817

818

The discharge curve is not linear so can’t simply use percentage to show the battery level. Below is the battery performance.

819

820

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]]

821

822

823

Minimum Working Voltage for the PS-LB:

PS-LB: 2.45v ~~ 3.6v

1.

11. Replace Battery

Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.

832

833

And make sure the positive and negative pins match.

1.

11. Power Consumption Analyze

839

840

Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.

841

842

843

Instruction to use as below:

844

845

846

Step 1: Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from:

847

848

[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]

849

850

851

Step 2: Open it and choose

* Product Model

* Uplink Interval

* Working Mode

And the Life expectation in difference case will be shown on the right.

858

859

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]]

860

861

862

The battery related documents as below:

863

864

* [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],

865

* [[Lithium-Thionyl Chloride Battery>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/ER18505_datasheet-EN.pdf]] datasheet, [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/ER18505_datasheet_PM-ER18505-S-02-LF_EN.pdf]]

866

* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]

|(((

JST-XH-2P connector

)))

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]]

1.

11.

111. Battery Note

The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.

1.

11.

111. Replace the battery

886

887

You can change the battery in the PS-LB.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.

888

889

890

The default battery pack of PS-LB includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)

1. Remote Configure device

898

11. Connect via BLE

899

900

Please see this instruction for how to configure via BLE:

901

902

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]]

1.

11. AT Command Set

1. OTA firmware update

909

910

Please see this link for how to do OTA firmware update.

911

912

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]

1. FAQ

11. How to use AT Command to access device?

920

921

See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]

1.

11. How to update firmware via UART port?

See:

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]

1.

11. How to change the LoRa Frequency Bands/Region

934

935

You can follow the instructions for [[how to upgrade image>>path:#3ygebqi]].

936

When downloading the images, choose the required image file for download.

1. Order Info

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]]

1. Packing Info

**Package Includes**:

953

954

* PS-LB LoRaWAN Pressure Sensor

955

956

**Dimension and weight**:

* Device Size: cm

* Device Weight: g

* Package Size / pcs : cm

* Weight / pcs : g

1. Support

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

968

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to

969

970

[[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]

971

972

Wiki source code of PS-LB -- LoRaWAN Air Water Pressure Sensor User Manual

Applications

Navigation