Changes for page CPN01- NB-IoT Outdoor Open/Close Dry Contact Sensor User Manual

Last modified by Mengting Qiu on 2024/04/02 16:56

From version < 54.2 >

edited by Xiaoling
on 2022/11/21 11:26

To version < 54.3 >

edited by Xiaoling
on 2022/12/15 12:00

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -13,7 +13,6 @@
  = 1.  Introduction =
--
  == 1.1  What is CPN01 NB-IoT Pulse/Contact Sensor ==
@@ -40,9 +40,7 @@
  \\To use CPN01, user needs to check if there is NB-IoT coverage in the field and with the Nb-IoT bands that CPN01 supports. If local operator support it, user needs to get a (% style="color:blue" %)**NB-IoT SIM card**(%%) from the operator and install into CPN01 to get NB-IoT network connection.
  )))
--
--
  == 1.2  Features ==
@@ -109,7 +109,6 @@
  [[image:image-20221021110415-3.png]]
--
  == 1.7  Pin Definitions and Switch ==
@@ -122,7 +122,6 @@
  CPN01 is pre-configured to connect to two external wires. The other pins are not used. If user wants to know more about other pins, please refer to the **[[LSN50v2 User Manual>>doc:Main.User Manual for LoRaWAN End Nodes.LSN50 & LSN50-V2 - LoRaWAN Sensor Node User Manual.WebHome]]**.
--
  === 1.7.2  Jumper JP2(Power ON/OFF) ===
@@ -129,7 +129,6 @@
  Power on Device when putting this jumper.
--
  === 1.7.3  BOOT MODE / SW1 ===
@@ -138,7 +138,6 @@
 )  Flash:  working mode, the device starts to work for NB-IoT connection and sends out console output for further debugging.
--
  === 1.7.4  Reset Button ===
@@ -145,7 +145,6 @@
  Press to reboot the device.
--
  === 1.7.5  LED ===
@@ -156,10 +156,8 @@
 .  Send an uplink packet
--
  = 2.  Use CPN01 to communicate with IoT Server =
--
  == 2.1  How it works ==
@@ -170,10 +170,8 @@
  [[image:image-20221021110615-5.png]]
--
  == 2.2  Configure CPN01 ==
--
  === 2.2.1  Test Requirement ===
@@ -187,9 +187,7 @@
  [[image:image-20221023000439-3.png]]
--
--
  === 2.2.2  Insert NB-IoT SIM card ===
@@ -200,7 +200,6 @@
  [[image:image-20221021110745-6.png]]
--
  === 2.2.3  Connect USB – TTL to CPN01 and configure it ===
@@ -237,7 +237,6 @@
  (% style="color:red" %)**Note: the valid AT Commands can be found at:  **(%%)[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
--
  === 2.2.4  Use CoAP protocol to uplink data ===
@@ -262,7 +262,6 @@
  [[image:image-20221021110956-9.png]]
--
  === 2.2.5  Use UDP protocol to uplink data(Default protocol) ===
@@ -279,9 +279,7 @@
  [[image:image-20221021111033-11.png||height="241" width="576"]]
--
--
  === 2.2.6  Use MQTT protocol to uplink data ===
@@ -311,7 +311,6 @@
  MQTT protocol has a much higher power consumption compare with UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
--
  === 2.2.7  Use TCP protocol to uplink data ===
@@ -323,11 +323,11 @@
   [[image:image-20221021111125-14.png]]
++
  [[image:image-20221021111131-15.png]]
--
  === 2.2.8  Change Update Interval ===
@@ -340,7 +340,6 @@
 .  By default, the device will send an uplink message every 1 hour.
--
  == 2.3  Uplink Payload ==
@@ -398,7 +398,6 @@
  == 2.4  Payload Explanation and Sensor Interface ==
--
  === 2.4.1  Device ID ===
@@ -413,7 +413,6 @@
  The Device ID is stored in a non-erase area, Upgrade the firmware or run AT+FDR won't erase the Device ID.
--
  === 2.4.2  Version Info ===
@@ -422,7 +422,6 @@
  For example 0x00 64 : This device is CPN01 with firmware version 1.0.0.
--
  === 2.4.3  Battery Info ===
@@ -433,7 +433,6 @@
  Ex2: 0x0B49 = 2889mV
--
  === 2.4.4  Signal Strength ===
@@ -452,7 +452,6 @@
  **99**      Not known or not detectable
--
  === 2.4.5  Calculate Flag ===
@@ -465,7 +465,6 @@
  Range (6 bits): (b)000000 ~~ (b) 111111
--
  === 2.4.6  Alarm ===
@@ -472,7 +472,6 @@
  See [[Alarm Base on Timeout>>||anchor="H2.7A0AlarmBaseonTimeout"]]
--
  === 2.4.7  Contact Status ===
@@ -481,7 +481,6 @@
 : Close
--
  === 2.4.8  Total pulse ===
@@ -490,7 +490,6 @@
  Range (3 Bytes) : 0x000000 ~~ 0xFFFFFF . Max: 16777215
--
  === 2.4.9  The last open duration ===
@@ -501,7 +501,6 @@
  [[image:image-20221021111346-17.png||height="146" width="770"]]
--
  === 2.4.10  Timestamp ===
@@ -511,7 +511,6 @@
  **~ **
--
  == 2.5  Downlink Payload ==
@@ -532,7 +532,7 @@
  * (% style="color:#037691" %)**Reset**
--If payload = 0x04FF, it will reset the NSE01
++If payload = 0x04FF, it will reset the CPN01
  * (% style="color:#037691" %)**INTMOD**
@@ -539,7 +539,6 @@
  Downlink Payload: 06000003, Set AT+INTMOD=3
--
  == 2.6  LED Indicator ==
@@ -580,7 +580,6 @@
  (% style="color:#037691" %)**AT+TTRIG=0,0 **  (%%)    **~-~->** Default Value, disable timeout Alarm.
--
  == 2.8  Set debug mode ==
@@ -591,7 +591,6 @@
  [[image:image-20221021111629-21.png]]
--
  == 2.9  Clear Flash Record ==
@@ -602,7 +602,6 @@
  [[image:image-20221021111527-19.png]]
--
  == 2.10  Set trigger mode ==
@@ -613,7 +613,6 @@
  [[image:image-20221021111552-20.png]]
--
  == 2.11  Set the calculate flag ==
@@ -624,7 +624,6 @@
  [[image:image-20221021111711-22.png]]
--
  == 2.12  Set count number ==
@@ -635,7 +635,6 @@
  [[image:image-20221021111748-24.png]]
--
  == 2.13  Set the number of data to be uploaded and the recording time ==
@@ -646,7 +646,6 @@
  (% style="color:#037691" %)**AT+NOUD=8 **     (%%)~/~/  The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
--
  == 2.14  Read or Clear cached data ==
@@ -659,7 +659,6 @@
  [[image:image-20221021111810-25.png||height="364" width="797"]]
--
  == 2.15  Firmware Change Log ==
@@ -668,10 +668,8 @@
  Upgrade Instruction: [[Upgrade Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
--
  == 2.16  Battery Analysis ==
--
  === 2.16.1  Battery Type ===
@@ -690,7 +690,6 @@
  [[image:image-20221021111911-26.png]]
--
  === 2.16.2  Power consumption Analyze ===
@@ -713,7 +713,6 @@
  [[image:1666596205057-567.png]]
--
  === 2.16.3  Battery Note ===
@@ -720,7 +720,6 @@
  The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
--
  === 2.16.4  Replace the battery ===
@@ -727,7 +727,6 @@
  The default battery pack of CPN01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
--
  = 3.  Access NB-IoT Module =
@@ -738,10 +738,8 @@
  [[image:image-20221021112006-28.png]]
--
  = 4.  Using the AT Commands =
--
  == 4.1  Access AT Commands ==
@@ -827,10 +827,8 @@
  AT+PWORD       : Serial Access Password
--
  = 5.  FAQ =
--
  == 5.1  How to Upgrade Firmware ==
@@ -841,10 +841,8 @@
  (% style="color:red" %)**Notice: **(% style="color:blue" %)**CPN01** (%%)**and (% style="color:blue" %)CPL01(%%)**(% style="color:blue" %) (%%)**share the same mother board. They use the same connection and method to update.**
--
  = 6.  Trouble Shooting =
--
  == 6.1  Connection problem when uploading firmware ==
@@ -851,7 +851,6 @@
  (% style="color:blue" %)**Please see: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting]]
--
  == 6.2  AT Command input doesn't work ==
@@ -858,7 +858,6 @@
  In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER** (%%)while press the send key, user need to add ENTER in their string.
--
  = 7.  Order Info =
@@ -865,7 +865,6 @@
  Part Number**:** CPN01
--
  = 8.  Packing Info =

Changes for page CPN01- NB-IoT Outdoor Open/Close Dry Contact Sensor User Manual

Summary

Details

Applications

Navigation