Version 57.1 by Kilight Cao on 2022/11/03 14:47
Show last authors
1 (% style="text-align:center" %)
2 [[image:image-20221028134937-1.jpeg||height="466" width="466"]]
3
4 (((
5
6
7
8 )))
9
10 **Table of Contents：**
11
12 {{toc/}}
13
14 = **1. Introduction** =
15
16
17 == **1.1 What is LG01v2** ==
18
19
20 (((
21 (((
22 The LG01v2 is an (% style="color:green" %)**open-source single channel LoRa Gateway**(%%). It lets you bridge LoRa wireless network to an IP network via (% style="color:green" %)**WiFi , Ethernet or Cellular Network**(%%) (via Optional 4G module). The LoRa wireless allows users to send data and reach extremely long ranges at low data rates.
23 )))
24
25 (((
26 LG01v2 supports (% style="color:green" %)**remote management**(%%). System Integrator can easy to remote monitor the gateway and maintain it.
27 )))
28
29
30
31 == **1.2 Specifications** ==
32
33
34 (% style="color:#037691" %)**Hardware System:**
35
36 * CPU: Quad-core Cortex-A7 1.2Ghz
37 * RAM: 512MB
38 * eMMC: 4GB
39
40 (% style="color:#037691" %)**Interface:**
41
42 * 10M/100M RJ45 Ports x 1
43 * WiFi 802.11 b/g/n
44
45 (% style="color:#037691" %)**Operating Condition:**
46
47 * Work Temperature: -20 ~~ 65°C
48 * Storage Temperature: -20 ~~ 65°C
49 * Power Input: 5V, 2A, DC
50
51 == **1.3 Features** ==
52
53
54 * Open Source Debian system
55 * Managed by Web GUI, SSH via WAN or WiFi
56 * Remote Management
57 * Auto-provisioning for batch deployment and management
58 * LoRa Gateway
59 * Built-in (% style="color:#037691" %)//**The Things Network**//(%%) local LoRaWAN server
60 * Built-in  (% style="color:#037691" %)//**Node-Red**// (%%)local Application server
61
62 == **1.4 Block Diagram** ==
63
64
65
66 == **1.5 LED Indicators** ==
67
68
69 LG01-V2 has totally four LEDs, They are:
70
71
72 (% style="color:blue" %)//**➢ Power LED**//(%%)//: This RED LED will be solid if the device is properly powered//
73
74 (% style="color:blue" %)//**➢ ETH LED**//(%%)//:  This RGB LED will blink GREEN when the ETH port is connecting//
75
76 (% style="color:blue" %)//**➢ SYS LED**//(%%)//:  This RGB LED will show different colors in different states~://
77
78 // ✓ **SOLID GREEN:** The device is alive with a LoRaWAN server connection.//
79
80 // ✓ **BLINKING GREEN:** a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will BLINKING GREEN for several seconds and then with BLINKING GREEN together//
81
82 // ✓** SOLID RED:** Device doesn't have an Internet connection.//
83
84 (% style="color:blue" %)//**➢ WIFI LED**//(%%)//: This LED shows the WIFI interface connection status.//
85
86
87
88 == **1.6 Button Intruction** ==
89
90
91 LG01v2 has a black toggle button, which is:
92
93
94 (% style="color:blue" %)**//➢ //Long press 4-5s  : **(%%)the gateway will reload the Network and Initialize wifi configuration
95
96 // **LED status: ** ETH LED will BLINKIND BULE Until the reload is finished.//
97
98
99 (% style="color:blue" %)//**➢ **//**Long press more than 10s:**(%%)**    **//the gateway will restore the factory settings.//
100
101 //**LED status: ** ETH LED will SOLID BULE Until the restore is finished.//
102
103
104
105 = **2. Quick Start** =
106
107
108 The LG01-V2 supports network access via Ethernet or Wi-Fi connection and runs without a network.
109
110 In most cases, the first thing you need to do is make the LG01-v2 accessible to the network.
111
112
113 == **2.1 Connects to the network and accesses the gateway Web UI** ==
114
115
116 == **2.1.1 connect the network.** ==
117
118
119 === (% style="color:blue" %)**Method 1**(%%):  Connect via Ethernet with DHCP IP from the router ===
120
121
122 Connect the LG01v2 Ethernet port to your router and LG01v2 can obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the LG01v2.
123
124 You can also use this IP to connect.
125
126
127 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622100129-1.png?width=1263&height=332&rev=1.1||alt="image-20220622100129-1.png"]]
128
129
130 === (% style="color:blue" %)**Method 2**(%%):  Connect via WiFi with DHCP IP from the router ===
131
132
133 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622100542-2.png?width=1256&height=369&rev=1.1||alt="image-20220622100542-2.png"]]
134
135 The LG01v2 has a fall-back IP address on its WAN port. you have to access the gateway Web-UI to configure the WiFi connection via the fallback IP address.
136
137
138 (% style="color:#037691" %)**Steps to connect via fallback IP:**
139
140 ~1. Connect PC's Ethernet port to LG01-V2's WAN port
141
142 2. Configure PC's Ethernet port has  IP: 172.31.255.253 and Netmask: 255.255.255.252
143
144
145 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622101433-4.png?rev=1.1||alt="image-20220622101433-4.png"]]
146
147
148 and then On the PC, use the IP address **http:~/~/172.31.255.254** to access the LG01-V2 via Web or Console.
149
150
151 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102210-5.png?width=919&height=504&rev=1.1||alt="image-20220622102210-5.png"]]
152
153
154 Fill in the WiFi information by checking the box and clicking (% style="color:red" %)**Save&Apply**
155
156
157 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102702-6.png?rev=1.1||alt="image-20220622102702-6.png"]]
158
159
160 **Wi-Fi configuration successful**
161
162
163 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102847-7.png?rev=1.1||alt="image-20220622102847-7.png"]]
164
165 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102901-8.png?width=938&height=476&rev=1.1||alt="image-20220622102901-8.png"]]
166
167
168 = **3. Web Configure Pages** =
169
170 == **3.1 Home** ==
171
172 //Shows the system running status~://
173
174 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102901-8.png?rev=1.1||alt="image-20220622102901-8.png" height="476" width="939"]]
175
176
177 == **3.2 Network Settings** ==
178
179
180 === **3.2.1 Network ~-~-> WiFi** ===
181
182
183 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220616114756-4.png?width=669&height=251&rev=1.1||alt="image-20220616114756-4.png"]]
184
185
186
187 === **3.4.2 Network ~-~-> System Status** ===
188
189
190 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220820134112-2.png?width=668&height=539&rev=1.1||alt="image-20220820134112-2.png"]]
191
192
193
194 === **3.4.3 Network ~-~-> Firewall** ===
195
196
197 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220616115351-6.png?width=661&height=244&rev=1.1||alt="image-20220616115351-6.png"]]
198
199
200
201 == **3.5 System** ==
202
203
204 === **3.5.1  System ~-~-> System Overview** ===
205
206
207 Shows the system info:
208
209 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220917144512-5.png?width=853&height=618&rev=1.1||alt="image-20220917144512-5.png"]]
210
211
212
213 === **3.5.2 System ~-~-> Backup/Restore** ===
214
215
216 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220917144725-6.png?width=869&height=208&rev=1.1||alt="image-20220917144725-6.png"]]
217
218
219
220 = **4. How to configure the Lora Gateway** =
221
222
223 == **4.1 Access the Lora configuration page** ==
224
225
226 Users can access the LA66 module by running the following command, then select the option **''serial port setup"**:
227
228 (% class="box infomessage" %)
229 (((
230 **root@dragino-2406ef:~~# minicom -s**
231 )))
232
233 [[image:image-20221029174637-2.png||height="410" width="524"]]
234
235
236 And then, change the setting:
237
238 (% class="box infomessage" %)
239 (((
240 **Serial Device :** **/dev/ttyUSB0**
241
242 **Bps/Par/Bits : 9600 8N1**
243 )))
244
245
246 (% style="color:red" %)**Note: Enter the corresponding letter to change the configuration, like A,B,C**(%%)
247 (% style="color:red" %)[[image:image-20221029174703-3.png]]
248
249
250 Enter **AT+CFG **in the interface to get the configuration,
251
252
253 (% class="box infomessage" %)
254 (((
255 AT+FRE=868.100,868.100  ~-~--> TX and RX frequency
256 AT+GROUPMOD=0,0  ~-~--> TX and RX group
257 AT+BW=0,0  ~-~--> TX and RX Bandwidth
258 AT+SF=12,12  ~-~--> TX and RX Spreading Factor
259 AT+POWER=14  ~-~--> TX Power Range
260 AT+CRC=1,1  ~-~--> TX and RX CRC Type
261 AT+HEADER=0,0  ~-~--> TX and RX Header Type
262 AT+CR=1,1  ~-~--> TX and RX Coding Rate
263 AT+IQ=0,0  ~-~--> TX and RX InvertIQ
264 AT+PREAMBLE=8,8  ~-~--> TX and RX Preamble Length
265 AT+SYNCWORD=0  ~-~-->  Syncword**(0: private，1: public)**
266 AT+RXMOD=65535,0  ~-~-->  Rx Timeout and Reply mode
267 AT+RXDAFORM=1                              
268 )))
269
270
271 == **4.2 Example: LG01v2 Peer-to-Peer** ==
272
273
274
275 [[image:image-20221103143618-5.png||height="274" width="612"]]
276
277
278 The user can run the AT command to set the LG01v2 RX window always open as a Receiver, the LA66 Shield uses **AT+SEND=1,hello world,2,3** to simulate sending data,
279
280 **Prerequisites: **The configuration of LG01v2 and  LA66 Shield must match, users can use **AT+CFG** to check all configurations.
281
282
283 (% style="color:red" %)**LG01v2 as Receiver: (configured as AT+RXMOD=65535,2)**
284
285 [[image:image-20221102140053-4.png]]
286
287
288 (% style="color:red" %)**LA66 Shield as Sender: (AT+SEND=1,hello world,2,3)**
289
290 [[image:1667456058832-484.png||height="291" width="353"]]
291
292
293 Instruction for Peer-to-Peer firmware:[[ **Instruction **>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LA66%20LoRaWAN%20Shield%20User%20Manual/Instruction%20for%20LA66%20Peer%20to%20Peer%20firmware/]]
294 )))
295
296
297 = **5. Build in Server** =
298
299
300 The default factory version of LG01-V2 is installed with the built-in Applicant server: (% style="color:blue" %)**Node-Red**
301
302
303 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220820115644-1.png?width=778&height=217&rev=1.1||alt="image-20220820115644-1.png"]]
304
305
306 (% style="color:red" %)**Note:**
307
308 **Path**: System ~-~-> Built-in Server
309
310
311 **Troubleshooting:**
312
313
314 **~ 1. URL does not jump properly**
315
316 For the Node-Red, you can use the local IP address and the port is 1880 to access it.
317
318
319
320 == **5.1 Application Server ~-~- Node-Red** ==
321
322
323 You can access the gateway's built-in AS server of (% style="color:blue" %)**Node-Red **(%%)via the URL((% style="background-color:yellow" %)__**//http:~/~/<hostname>:1880 or http:~/~/<local-IPV4-address>//**__(%%)) in your browser.
324
325
326 Such as (% style="background-color:yellow" %)__**//http:~/~/dragino-54ff12:1880  or http:~/~/<Local-IPV4-Address>//**__
327
328
329 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220725172124-3.png?width=843&height=610&rev=1.1||alt="image-20220725172124-3.png"]]
330
331
332 = (% style="color:inherit; font-family:inherit; font-size:29px" %)**6. How users can access LG01v2 using serial USB**(%%) =
333
334
335 (% style="color:blue" %)**USB TTL to LG01v2  Connection:**
336
337
338 Port 1 of the UART on the LG01v2 is GND
339
340 (% class="box infomessage" %)
341 (((
342 **TXD  <~-~--> UART RXD (Gray line)**
343
344 **RXD  <~-~--> UART TXD (White line)**
345
346 **GND <~-~--> GND (Black line)**
347 )))
348
349
350 **LG01v2 UART connection photo**
351
352 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220804163015-1.png?width=466&height=621&rev=1.1||alt="image-20220804163015-1.png"]]
353
354
355
356 In the PC, you can use the serial port tool(such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows), you need to set the serial baud rate to (% style="color:blue" %)**115200**(%%) to access the serial console for LG01v2. LG01v2 will output system info once power on as below:
357
358
359 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220804164928-3.png?width=332&height=320&rev=1.1||alt="image-20220804164928-3.png"]]
360
361 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220804164747-2.png?width=594&height=622&rev=1.1||alt="image-20220804164747-2.png"]]
362
363
364 = **7. FAQ** =
365
366
367 == **7.1 How does LG01v2 communicate with Lora shield (LoRa.h)** ==
368
369
370 This example describes how to use LG01v2, LoRa Shield to set up a LoRa network
371
372 [[image:image-20221103144405-6.png||height="253" width="712"]]
373
374
375 (% style="color:red" %)**Prerequisites: The configurations of LG01v2 and Lora shield must match**
376
377 **LG01v2 configuration:**
378
379 (% class="box infomessage" %)
380 (((
381 AT+FRE=868.100,868.100  ~-~--> TX and RX frequency set :868100000
382 AT+BW=0,0  ~-~--> TX and RX Bandwidth set : 125kHz
383 AT+SF=12,12  ~-~--> TX and RX Spreading Factor
384 AT+POWER=14  ~-~--> TX Power Range
385 AT+CRC=1,1  ~-~--> TX and RX CRC Type
386 AT+HEADER=0,0  ~-~--> TX and RX Header Type
387 AT+CR=1,1  ~-~--> TX and RX Coding Rate
388 AT+IQ=0,0  ~-~--> TX and RX InvertIQ
389 AT+PREAMBLE=8,8  ~-~--> TX and RX Preamble Length
390 AT+SYNCWORD=0  ~-~-->  Syncword**(0: private，1: public)**
391 AT+RXMOD=65535,0  ~-~-->  Rx Timeout and Reply mode
392 AT+RXDAFORM=1    
393 )))
394
395 **Lora shield configuration:**
396
397 Lora Shield example: [[attach:LoRa_Shield_Sketch_For_MQTT.ino||target="_blank"]] , [[attach:arduino-LoRa-master.zip||target="_blank"]]
398
399 [[image:image-20221101161318-2.png]]
400
401
402 **Test LG01v2 to receive Lora Shield data:**
403
404 [[image:image-20221101161951-3.png]]
405
406
407 **Test the LG01v2 to send data:**
408
409 [[image:image-20221101162527-4.png]]
410
411
412 = (% style="color:inherit; font-family:inherit; font-size:29px" %)**8. Supports**(%%) =
413
414
415 (((
416 **//If you are experiencing issues and can't solve them, you can send mail to [[support@dragino.com>>mailto:support@dragino.com]].//**
417 )))
418
419 (((
420 **//With your question as detailed as possible. We will reply and help you in the shortest.//**
421
422
423
424 = **9. Reference** =
425
426
427 * Install Tago Core: Refer **Install Tago Core in LPS8v2** in[[ Instruction>>doc:Main.Tago\.IO.WebHome]].
428 * [[Advance OS Reference Guide for LPS8v2>>doc:Main.Armbian OS instruction.WebHome]].
429
430
431 )))
432
433 = **10. Order Info** =
434
435
436 (% style="color:#0000ff" %)**LPS8v2-XXX-YYY**
437
438 (% style="color:#0000ff" %)**XXX**(% style="color:black" %): Frequency Band
439
440 * (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
441 * (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
442 * (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
443 * (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
444 * (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
445 * (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
446
447 (% style="color:#0000ff" %)**YYY**(% style="color:black" %): 4G Cellular Option
448
449 * (% style="color:red" %)**E**(%%):  EMEA, Korea, Thailand, India.
450 * (% style="color:red" %)**A**(%%):  North America/ Rogers/AT&T/T-Mobile.
451 * (% style="color:red" %)**AU**(%%): Latin America, New Zeland, Taiwan
452 * (% style="color:red" %)**J**(%%):  Japan, DOCOMO/SoftBank/ KDDI
453
454 More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
455
456
457
458 = **10. Manufacturer Info** =
459
460
461 **Shenzhen Dragino Technology Development co. LTD**
462
463 Room 202, Block B, BCT Incubation Bases (BaoChengTai),  No.8 CaiYunRoad
464
465 LongCheng Street, LongGang District ; Shenzhen 518116,China
466
467
468
469 = **11. FCC Warning** =
470
471
472 (((
473 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
474 )))
475
476 (((
477 ~-~- Reorient or relocate the receiving antenna.
478 )))
479
480 (((
481 ~-~- Increase the separation between the equipment and receiver.
482 )))
483
484 (((
485 ~-~- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
486 )))
487
488 (((
489 ~-~- Consult the dealer or an experienced radio/TV technician for help.
490 )))
491
492
493 (((
494 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
495 )))
496
497
498 (((
499 The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
500
501
502 )))
503
504 ~)~)~)

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0