Show last authors
1 (% style="text-align:center" %)
2 [[image:image-20221028134937-1.jpeg||height="466" width="466"]]
3
4 (((
5
6
7
8 )))
9
10 **Table of Contents:**
11
12 {{toc/}}
13
14 = **1. Introduction** =
15
16
17 == **1.1 What is LG01v2** ==
18
19
20 (((
21 (((
22 The LG01v2 is an (% style="color:green" %)**open-source single channel LoRa Gateway**(%%). It lets you bridge LoRa wireless network to an IP network via (% style="color:green" %)**WiFi , Ethernet or Cellular Network**(%%) (via Optional 4G module). The LoRa wireless allows users to send data and reach extremely long ranges at low data rates.
23 )))
24
25 (((
26 LG01v2 supports (% style="color:green" %)**remote management**(%%). System Integrator can easy to remote monitor the gateway and maintain it.
27 )))
28
29
30
31 == **1.2 Specifications** ==
32
33
34 (% style="color:#037691" %)**Hardware System:**
35
36 * CPU: Quad-core Cortex-A7 1.2Ghz
37 * RAM: 512MB
38 * eMMC: 4GB
39
40 (% style="color:#037691" %)**Interface:**
41
42 * 10M/100M RJ45 Ports x 1
43 * WiFi 802.11 b/g/n
44
45 (% style="color:#037691" %)**Operating Condition:**
46
47 * Work Temperature: -20 ~~ 65°C
48 * Storage Temperature: -20 ~~ 65°C
49 * Power Input: 5V, 2A, DC
50
51 == **1.3 Features** ==
52
53
54 * Open Source Debian system
55 * Managed by Web GUI, SSH via WAN or WiFi
56 * Remote Management
57 * Auto-provisioning for batch deployment and management
58 * LoRa Gateway
59 * Built-in (% style="color:#037691" %)//**The Things Network**//(%%) local LoRaWAN server
60 * Built-in  (% style="color:#037691" %)//**Node-Red**// (%%)local Application server
61
62 == **1.4 Block Diagram** ==
63
64
65
66 == **1.5 LED Indicators** ==
67
68
69 LG01-V2 has totally four LEDs, They are:
70
71
72 (% style="color:blue" %)//**➢ Power LED**//(%%)//: This RED LED will be solid if the device is properly powered//
73
74 (% style="color:blue" %)//**➢ ETH LED**//(%%)//:  This RGB LED will blink GREEN when the ETH port is connecting//
75
76 (% style="color:blue" %)//**➢ SYS LED**//(%%)//:  This RGB LED will show different colors in different states~://
77
78 // ✓ **SOLID GREEN:** The device is alive with a LoRaWAN server connection.//
79
80 // ✓ **BLINKING GREEN:** a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will BLINKING GREEN for several seconds and then with BLINKING GREEN together//
81
82 // ✓** SOLID RED:** Device doesn't have an Internet connection.//
83
84 (% style="color:blue" %)//**➢ WIFI LED**//(%%)//: This LED shows the WIFI interface connection status.//
85
86
87
88 == **1.6 Button Intruction** ==
89
90
91 LG01v2 has a black toggle button, which is:
92
93
94 (% style="color:blue" %)**//➢ //Long press 4-5s  : **(%%)the gateway will reload the Network and Initialize wifi configuration
95
96 // **LED status: ** ETH LED will BLINKIND BULE Until the reload is finished.//
97
98
99 (% style="color:blue" %)//**➢ **//**Long press more than 10s:**(%%)**    **//the gateway will restore the factory settings.//
100
101 //**LED status: ** ETH LED will SOLID BULE Until the restore is finished.//
102
103
104
105 = **2. Quick Start** =
106
107
108 The LG01-V2 supports network access via Ethernet or Wi-Fi connection and runs without a network.
109
110 In most cases, the first thing you need to do is make the LG01-v2 accessible to the network.
111
112
113 == **2.1 Connects to the network and accesses the gateway Web UI** ==
114
115
116 == **2.1.1 connect the network.** ==
117
118
119 === (% style="color:blue" %)**Method 1**(%%):  Connect via Ethernet with DHCP IP from the router ===
120
121
122 Connect the LG01v2 Ethernet port to your router and LG01v2 can obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the LG01v2.
123
124 You can also use this IP to connect.
125
126
127 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622100129-1.png?width=1263&height=332&rev=1.1||alt="image-20220622100129-1.png"]]
128
129
130 === (% style="color:blue" %)**Method 2**(%%):  Connect via WiFi with DHCP IP from the router ===
131
132
133 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622100542-2.png?width=1256&height=369&rev=1.1||alt="image-20220622100542-2.png"]]
134
135 The LG01v2 has a fall-back IP address on its WAN port. you have to access the gateway Web-UI to configure the WiFi connection via the fallback IP address.
136
137
138 (% style="color:#037691" %)**Steps to connect via fallback IP:**
139
140 ~1. Connect PC's Ethernet port to LG01-V2's WAN port
141
142 2. Configure PC's Ethernet port has  IP: 172.31.255.253 and Netmask: 255.255.255.252
143
144
145 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622101433-4.png?rev=1.1||alt="image-20220622101433-4.png"]]
146
147
148 and then On the PC, use the IP address **http:~/~/172.31.255.254** to access the LG01-V2 via Web or Console.
149
150
151 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102210-5.png?width=919&height=504&rev=1.1||alt="image-20220622102210-5.png"]]
152
153
154 Fill in the WiFi information by checking the box and clicking (% style="color:red" %)**Save&Apply**
155
156
157 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102702-6.png?rev=1.1||alt="image-20220622102702-6.png"]]
158
159
160 **Wi-Fi configuration successful**
161
162
163 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102847-7.png?rev=1.1||alt="image-20220622102847-7.png"]]
164
165 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102901-8.png?width=938&height=476&rev=1.1||alt="image-20220622102901-8.png"]]
166
167
168 = **3. Web Configure Pages** =
169
170 == **3.1 Home** ==
171
172 //Shows the system running status~://
173
174 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102901-8.png?rev=1.1||alt="image-20220622102901-8.png" height="476" width="939"]]
175
176
177 == **3.2 Network Settings** ==
178
179
180 === **3.2.1 Network ~-~-> WiFi** ===
181
182
183 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220616114756-4.png?width=669&height=251&rev=1.1||alt="image-20220616114756-4.png"]]
184
185
186
187 === **3.4.2 Network ~-~-> System Status** ===
188
189
190 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220820134112-2.png?width=668&height=539&rev=1.1||alt="image-20220820134112-2.png"]]
191
192
193
194 === **3.4.3 Network ~-~-> Firewall** ===
195
196
197 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220616115351-6.png?width=661&height=244&rev=1.1||alt="image-20220616115351-6.png"]]
198
199
200
201 == **3.5 System** ==
202
203
204 === **3.5.1  System ~-~-> System Overview** ===
205
206
207 Shows the system info:
208
209 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220917144512-5.png?width=853&height=618&rev=1.1||alt="image-20220917144512-5.png"]]
210
211
212
213 === **3.5.2 System ~-~-> Backup/Restore** ===
214
215
216 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220917144725-6.png?width=869&height=208&rev=1.1||alt="image-20220917144725-6.png"]]
217
218
219
220 = **4. How to configure the Lora Gateway** =
221
222
223 == **4.1 Access the Lora configuration page** ==
224
225
226 Users can access the LA66 module by running the following command, then select the option **''serial port setup"**:
227
228 (% class="box infomessage" %)
229 (((
230 **root@dragino-2406ef:~~# minicom -s**
231 )))
232
233 [[image:image-20221029174637-2.png||height="410" width="524"]]
234
235
236 And then, change the setting:
237
238 (% class="box infomessage" %)
239 (((
240 **Serial Device :** **/dev/ttyUSB0**
241
242 **Bps/Par/Bits : 9600 8N1**
243 )))
244
245
246 (% style="color:red" %)**Note: Enter the corresponding letter to change the configuration, like A,B,C**(%%)
247 (% style="color:red" %)[[image:image-20221029174703-3.png]]
248
249
250 Enter **AT+CFG **in the interface to get the configuration,
251
252
253 (% class="box infomessage" %)
254 (((
255 AT+FRE=868.100,868.100  ~-~--> TX and RX frequency
256 AT+GROUPMOD=0,0  ~-~--> TX and RX group
257 AT+BW=0,0  ~-~--> TX and RX Bandwidth
258 AT+SF=12,12  ~-~--> TX and RX Spreading Factor
259 AT+POWER=14  ~-~--> TX Power Range
260 AT+CRC=1,1  ~-~--> TX and RX CRC Type
261 AT+HEADER=0,0  ~-~--> TX and RX Header Type
262 AT+CR=1,1  ~-~--> TX and RX Coding Rate
263 AT+IQ=0,0  ~-~--> TX and RX InvertIQ
264 AT+PREAMBLE=8,8  ~-~--> TX and RX Preamble Length
265 AT+SYNCWORD=0  ~-~-->  Syncword**(0: private,1: public)**
266 AT+RXMOD=65535,0  ~-~-->  Rx Timeout and Reply mode
267 AT+RXDAFORM=1                              
268 )))
269
270
271 == **4.2 Example: LG01v2 Peer-to-Peer** ==
272
273
274 [[image:image-20221103140645-1.png]]
275
276 The user can run the AT command to set the LG01v2 RX window always open as a Receiver, the Sender uses **AT+SEND=1,hello world,2,3** to simulate sending data,
277
278 **Prerequisites: **The configuration of LG01v2 and Sender must match, users can use **AT+CFG** to check all configurations.
279
280
281 (% style="color:red" %)**LG01v2 as Receiver: (configured as AT+RXMOD=65535,2)**
282
283 [[image:image-20221102140053-4.png]]
284
285
286 (% style="color:red" %)**Sender: (AT+SEND=1,hello world,2,3)**
287
288 [[image:image-20221031092053-4.png]]
289
290
291 Instruction for Peer-to-Peer firmware:[[ **Instruction **>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LA66%20LoRaWAN%20Shield%20User%20Manual/Instruction%20for%20LA66%20Peer%20to%20Peer%20firmware/]]
292 )))
293
294
295 = **5. Build in Server** =
296
297
298 The default factory version of LG01-V2 is installed with the built-in Applicant server: (% style="color:blue" %)**Node-Red**
299
300
301 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220820115644-1.png?width=778&height=217&rev=1.1||alt="image-20220820115644-1.png"]]
302
303
304 (% style="color:red" %)**Note:**
305
306 **Path**: System ~-~-> Built-in Server
307
308
309 **Troubleshooting:**
310
311
312 **~ 1. URL does not jump properly**
313
314 For the Node-Red, you can use the local IP address and the port is 1880 to access it.
315
316
317
318 == **5.1 Application Server ~-~- Node-Red** ==
319
320
321 You can access the gateway's built-in AS server of (% style="color:blue" %)**Node-Red **(%%)via the URL((% style="background-color:yellow" %)__**//http:~/~/<hostname>:1880 or http:~/~/<local-IPV4-address>//**__(%%)) in your browser.
322
323
324 Such as (% style="background-color:yellow" %)__**//http:~/~/dragino-54ff12:1880  or http:~/~/<Local-IPV4-Address>//**__
325
326
327 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220725172124-3.png?width=843&height=610&rev=1.1||alt="image-20220725172124-3.png"]]
328
329
330 = (% style="color:inherit; font-family:inherit; font-size:29px" %)**6. How users can access LG01v2 using serial USB**(%%) =
331
332
333 (% style="color:blue" %)**USB TTL to LG01v2  Connection:**
334
335
336 Port 1 of the UART on the LG01v2 is GND
337
338 (% class="box infomessage" %)
339 (((
340 **TXD  <~-~--> UART RXD (Gray line)**
341
342 **RXD  <~-~--> UART TXD (White line)**
343
344 **GND <~-~--> GND (Black line)**
345 )))
346
347
348 **LG01v2 UART connection photo**
349
350 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220804163015-1.png?width=466&height=621&rev=1.1||alt="image-20220804163015-1.png"]]
351
352
353
354 In the PC, you can use the serial port tool(such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows), you need to set the serial baud rate to (% style="color:blue" %)**115200**(%%) to access the serial console for LG01v2. LG01v2 will output system info once power on as below:
355
356
357 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220804164928-3.png?width=332&height=320&rev=1.1||alt="image-20220804164928-3.png"]]
358
359 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220804164747-2.png?width=594&height=622&rev=1.1||alt="image-20220804164747-2.png"]]
360
361
362 = **7. FAQ** =
363
364
365 == **7.1 How does LG01v2 communicate with Lora shield (LoRa.h)** ==
366
367
368 (% style="color:red" %)**Prerequisites: The configurations of LG01v2 and Lora shield must match**
369
370 **LG01v2 configuration:**
371
372 (% class="box infomessage" %)
373 (((
374 AT+FRE=868.100,868.100  ~-~--> TX and RX frequency set :868100000
375 AT+BW=0,0  ~-~--> TX and RX Bandwidth set : 125kHz
376 AT+SF=12,12  ~-~--> TX and RX Spreading Factor
377 AT+POWER=14  ~-~--> TX Power Range
378 AT+CRC=1,1  ~-~--> TX and RX CRC Type
379 AT+HEADER=0,0  ~-~--> TX and RX Header Type
380 AT+CR=1,1  ~-~--> TX and RX Coding Rate
381 AT+IQ=0,0  ~-~--> TX and RX InvertIQ
382 AT+PREAMBLE=8,8  ~-~--> TX and RX Preamble Length
383 AT+SYNCWORD=0  ~-~-->  Syncword**(0: private,1: public)**
384 AT+RXMOD=65535,0  ~-~-->  Rx Timeout and Reply mode
385 AT+RXDAFORM=1    
386 )))
387
388 **Lora shield configuration:**
389
390 Lora Shield example: [[attach:LoRa_Shield_Sketch_For_MQTT.ino||target="_blank"]] , [[attach:arduino-LoRa-master.zip||target="_blank"]]
391
392 [[image:image-20221101161318-2.png]]
393
394
395 **Test LG01v2 to receive Lora Shield data:**
396
397 [[image:image-20221101161951-3.png]]
398
399
400 **Test the LG01v2 to send data:**
401
402 [[image:image-20221101162527-4.png]]
403
404
405 = (% style="color:inherit; font-family:inherit; font-size:29px" %)**8. Supports**(%%) =
406
407
408 (((
409 **//If you are experiencing issues and can't solve them, you can send mail to [[support@dragino.com>>mailto:support@dragino.com]].//**
410 )))
411
412 (((
413 **//With your question as detailed as possible. We will reply and help you in the shortest.//**
414
415
416
417 = **9. Reference** =
418
419
420 * Install Tago Core: Refer **Install Tago Core in LPS8v2** in[[ Instruction>>doc:Main.Tago\.IO.WebHome]].
421 * [[Advance OS Reference Guide for LPS8v2>>doc:Main.Armbian OS instruction.WebHome]].
422
423
424 )))
425
426 = **10. Order Info** =
427
428
429 (% style="color:#0000ff" %)**LPS8v2-XXX-YYY**
430
431 (% style="color:#0000ff" %)**XXX**(% style="color:black" %): Frequency Band
432
433 * (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
434 * (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
435 * (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
436 * (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
437 * (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
438 * (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
439
440 (% style="color:#0000ff" %)**YYY**(% style="color:black" %): 4G Cellular Option
441
442 * (% style="color:red" %)**E**(%%):  EMEA, Korea, Thailand, India.
443 * (% style="color:red" %)**A**(%%):  North America/ Rogers/AT&T/T-Mobile.
444 * (% style="color:red" %)**AU**(%%): Latin America, New Zeland, Taiwan
445 * (% style="color:red" %)**J**(%%):  Japan, DOCOMO/SoftBank/ KDDI
446
447 More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
448
449
450
451 = **10. Manufacturer Info** =
452
453
454 **Shenzhen Dragino Technology Development co. LTD**
455
456 Room 202, Block B, BCT Incubation Bases (BaoChengTai),  No.8 CaiYunRoad
457
458 LongCheng Street, LongGang District ; Shenzhen 518116,China
459
460
461
462 = **11. FCC Warning** =
463
464
465 (((
466 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
467 )))
468
469 (((
470 ~-~- Reorient or relocate the receiving antenna.
471 )))
472
473 (((
474 ~-~- Increase the separation between the equipment and receiver.
475 )))
476
477 (((
478 ~-~- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
479 )))
480
481 (((
482 ~-~- Consult the dealer or an experienced radio/TV technician for help.
483 )))
484
485
486 (((
487 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
488 )))
489
490
491 (((
492 The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
493
494
495 )))
496
497 ~)~)~)
Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0