Summary

• Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-XWiki.Edwin
	1	+XWiki.Bei

Content

...	...	@@ -16,7 +16,7 @@
16	16	(% border="1" cellspacing="10" class="doOddEven filterable grid sortable" id="tableid" style="background-color:#f7faff; width:621.989px" %)
17	17	(% class="sortHeader" %)|=(% style="width: 77px;" %)Model|=(% style="width: 120px;" %)Mother Board|=(% style="width: 199px;" %)UART for AT Commands|=(% style="width: 221px;" %)UART for Upgrade Firmware
18	18	|(% style="width:77px" %)(((
19		-PS-LB
	19	+**PS-LB **
20	20	)))|(% style="width:120px" %)SIB|(% style="width:199px" %)Instruction|(% style="width:221px" %)Instruction
21	21
22	22	= 2. UART for AT Commands =
...	...	@@ -31,13 +31,13 @@
31	31	1. (((
32	32	The password is the last six characters of APPSKEY or PIN of box
33	33
34		-**Example：**
	34	+Example：
35	35
36	36	APPSKEY= 41 85 71 A7 5D 7E 54 52 25 58 74 85 96 14 74 85
37	37
38	38	The password：147485
39	39
40		-[[image:image-20230329162900-1.png||height="302" width="648"]]
	40	+[[image:https://qiye.aliyun.com/attachment/downloadex?ri=%2Falimail%2FinternalLinks%2FrefreshToken&o=1&et=normal&ext=png&e=jinggeng.bei%40dragino.cc&f=3e538434-66e4-4c2a-abd3-d6a69fd04ec6&m=2_0%3ADzzzzyPr-xZ%24---.S1oEkZQ&n=image013.png]][[image:image-20230329162900-1.png||height="302" width="648"]]
41	41
42	42
43	43	)))
...	...	@@ -51,16 +51,11 @@
51	51	[[image:image-20221224171304-3.png||height="545" width="863"]]
52	52
53	53
54		-== 2.3 UART Connection for SN50v3 base mother board ==
55		-
56		-
57	57	= 3. UART for Firmware Upgrade =
58	58
59		-== 3.1 Update firmware ==
	56	+== 3.1 General Instruction for UART update firmware ==
60	60
61		-=== 3.1.1 Update a firmware without bootloader ===
62	62
63		-
64	64	LoRaSTv4 Base hardware support UART update firmware. the UART connection is the same as AT Command connection, with the need for two extra action. See below for the steps:
65	65
66	66	(% style="color:blue" %)**Step1**(%%): Set BOOT Switch to (% style="color:blue" %)**PROG**(%%) mode. PROG mode is for update firmware specially.
...	...	@@ -78,7 +78,7 @@
78	78
79	79	2.  Run** (% style="color:blue" %)TremoProgrammer.(%%)**
80	80
81		-3.  Choose software and set the address to (% style="color:blue" %)**0x0800D000(%%)**. (% style="color:red" %)VERY IMPORTANT: USE THIS ADDRESS FOR FIRMWARE WITHOUT BOOTLOADER(%%)
	76	+3.  Choose software and set the address to (% style="color:blue" %)**0x0800D000**
82	82
83	83	4. Rember to set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) after update
84	84