Changes for page Node-RED_Install and Use

Last modified by Herong Lu on 2024/03/05 08:37
<
From version < 21.1 >
edited by Herong Lu
on 2022/05/25 18:43
To version < 20.2 >
edited by Herong Lu
on 2022/05/25 18:42
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,70 +1,70 @@
1 1  (% class="wikigeneratedid" id="HEndDeviceFrequencyBand" %)
2 - **Contents：**
2 + **内容：**
3 3  
4 4  {{toc/}}
5 5  
6 -= Installation =
6 += 安装 =
7 7  
8 -Check installation instruction for different OS from this link: [[https:~~/~~/nodered.org/docs/getting-started/>>https://nodered.org/docs/getting-started/]]
8 +从此链接检查不同操作系统的安装说明：[[https :~~/~~/nodered.org/docs/getting-started/>>https://nodered.org/docs/getting-started/]]
9 9  
10 -== Install Example for CENTOS ==
10 +== CENTOS 的安装示例 ==
11 11  
12 -=== Installation ===
12 +=== 安装 ===
13 13  
14 14  (% class="box infomessage" %)
15 15  (((
16 -Reference Instruction from this link:  [[https:~~/~~/github.com/node-red/linux-installers>>https://github.com/node-red/linux-installers]]
17 -Run below commands and wait for installation complete.
16 +此链接的参考说明：   [[https>>https://github.com/node-red/linux-installers]]
17 +:~/~/github.com/node-red/linux-installers运行以下命令并等待安装完成。
18 18  )))
19 19  
20 20  [[image:image-20220519102228-2.png]]
21 21  
22 -**Verify if the installation was successful**
22 +**验证是否安装成功**
23 23  
24 -Type in the command line interface  node-red  
24 +在命令行界面输入node-red  
25 25  
26 -The following information appears to prove that the installation has been successful
26 +出现以下信息证明安装成功
27 27  
28 28  [[image:image-20220519103318-3.png]]
29 29  
30 30  
31 -=== If you want to start Node-RED as a background process ===
31 +=== 如果要将 Node-RED 作为后台进程启动 ===
32 32  
33 -Type in the command line interface  nohup node-red &
33 +在命令行界面输入 nohup node-red &
34 34  
35 -It will prompt after startup
35 +启动后会提示
36 36  
37 37  [[image:image-20220519104601-5.png]]
38 38  
39 -After seeing the above information, press enter
39 +看到以上信息后，按回车
40 40  
41 -Type in the command line  exit
41 +输入命令行退出
42 42  
43 -The above is the installation and startup process of nodered. If you don't understand anything, you can go to the nodered official website. There are installation instructions for various systems. The address has a link at the top
43 +以上就是nodered的安装和启动过程。有什么不懂的可以去nodered官网看看。有各种系统的安装说明。地址顶部有链接
44 44  
45 -== Install in Dragino Gataway ==
45 +== 在 Dragino Gataway 中安装 ==
46 46  
47 47  
48 -= Use Node-RED =
48 += 使用 Node-RED =
49 49  
50 -== Login to Node-RED interface ==
50 +== 登录 Node-RED 界面 ==
51 51  
52 -Enter your public IP address followed by the port number 1880
52 +输入您的公共 IP 地址，后跟端口号 1880
53 53  
54 -example：[[http:~~/~~/xxx.xx.xx.xx:1880/>>http://119.91.62.30:1880/]]
54 +例子：[[http:~~/~~/xxx.xx.xx.xx:1880/>>http://119.91.62.30:1880/]]
55 55  
56 56  [[image:image-20220519104115-4.png||height="352" width="969"]]
57 57  
58 58  
59 -== Add flow ==
59 +== 添加流 ==
60 60  
61 -Take NBSN95 mod1 UDP protocol as an example
61 +以NBSN95 mod1 UDP协议为例
62 62  
63 -After logging into the interface click '+' to create a flow
63 +登录界面后点击“+”创建流程
64 64  
65 65  [[image:http://8.211.40.43:8080/xwiki/bin/download/Main/Node-RED/node_red%20usage%20example/WebHome/image-20220519133634-1.png?rev=1.1||alt="image-20220519133634-1.png" height="231" width="972"]]
66 66  
67 -Rename the stream
67 +重命名流
68 68  
69 69  [[image:http://8.211.40.43:8080/xwiki/bin/download/Main/Node-RED/node_red%20usage%20example/WebHome/image-20220519134042-2.png?rev=1.1||alt="image-20220519134042-2.png" height="552" width="565"]]
70 70  
... ... @@ -72,26 +72,26 @@
72 72  
73 73  [[image:http://8.211.40.43:8080/xwiki/bin/download/Main/Node-RED/node_red%20usage%20example/WebHome/image-20220519134346-4.png?rev=1.1||alt="image-20220519134346-4.png"]]
74 74  
75 -Drag UDP into the editing area
75 +将UDP拖入编辑区
76 76  
77 77  [[image:http://8.211.40.43:8080/xwiki/bin/download/Main/Node-RED/node_red%20usage%20example/WebHome/image-20220519134533-5.png?rev=1.1||alt="image-20220519134533-5.png"]]
78 78  
79 -The same method as above, drag and drop functions and debug into the editing area
79 +方法同上，拖拽函数和调试到编辑区
80 80  
81 81  [[image:http://8.211.40.43:8080/xwiki/bin/download/Main/Node-RED/node_red%20usage%20example/WebHome/image-20220519134850-6.png?rev=1.1||alt="image-20220519134850-6.png"]]
82 82  
83 -configure UDP in
83 +配置UDP
84 84  
85 85  [[image:http://8.211.40.43:8080/xwiki/bin/download/Main/Node-RED/node_red%20usage%20example/WebHome/image-20220519135402-7.png?rev=1.1||alt="image-20220519135402-7.png"]]
86 86  
87 -Write to the UDP port that the device node sends to the server
87 +写入设备节点发送给服务器的UDP端口
88 88  
89 -Example My UDP device node sends to server port 8585
90 -just write 8585
89 +示例 我的 UDP 设备节点发送到服务器端口 8585
90 +只需写入 8585
91 91  
92 -Note that the port that is already in use cannot be used. If the receiving fails, you need to check whether the port of the server is occupied. The sending port of the device node should not use the default port used by the server, such as a common port such as 8080.
92 +请注意，不能使用已在使用的端口。如果接收失败，需要检查服务器的端口是否被占用。设备节点的发送端口不应使用服务器默认使用的端口，如8080等常用端口。
93 93  
94 -In order to avoid data confusion, different types of nodes do not use the same UDP port, because different nodes have different data formats and different functions.
94 +为了避免数据混淆，不同类型的节点不使用相同的UDP端口，因为不同的节点有不同的数据格式和不同的功能。
95 95  
96 96  [[image:http://8.211.40.43:8080/xwiki/bin/download/Main/Node-RED/node_red%20usage%20example/WebHome/image-20220519135915-8.png?rev=1.1||alt="image-20220519135915-8.png"]]
97 97  
... ... @@ -101,28 +101,28 @@
101 101  
102 102  [[image:http://8.211.40.43:8080/xwiki/bin/download/Main/Node-RED/node_red%20usage%20example/WebHome/image-20220519141704-12.png?rev=1.1||alt="image-20220519141704-12.png"]]
103 103  
104 -When the node successfully sends data, the effect shown in the following figure will appear
104 +当节点发送数据成功后，会出现下图的效果
105 105  
106 106  [[image:http://8.211.40.43:8080/xwiki/bin/download/Main/Node-RED/node_red%20usage%20example/WebHome/image-20220519150455-15.png?rev=1.1||alt="image-20220519150455-15.png"]]
107 107  
108 -=== About function ===
108 +=== 关于功能 ===
109 109  
110 -If you are familiar with JS code, you can write it yourself
111 -If you are not familiar, we have the JS code for each type of node, you just need to copy and paste it into it
110 +如果你熟悉JS代码，可以自己写
111 +如果你不熟悉，我们有每种节点的JS代码，你只需要复制粘贴进去
112 112  
113 113  [[image:http://8.211.40.43:8080/xwiki/bin/download/Main/Node-RED/node_red%20usage%20example/WebHome/image-20220519141833-13.png?rev=1.1||alt="image-20220519141833-13.png"]]
114 114  
115 115  
116 -== Plot Chart for sensors ==
116 +== 传感器绘图图 ==
117 117  
118 118  
119 -== Store Value ==
119 +== 存储价值 ==
120 120  
121 121  
122 -== Email Notification ==
122 +== 电子邮件通知 ==
123 123  
124 124  
125 -= Input Flow =
125 += 输入流 =
126 126  
127 127  == MQTT ==
128 128  
... ... @@ -130,7 +130,7 @@
130 130  
131 131  == TCP ==
132 132  
133 -== Get data from LoRaWAN Server (TTN) ==
133 +== 从 LoRaWAN 服务器 (TTN) 获取数据 ==
134 134  
135 135  
136 -= Example =
136 += 例子 =

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0