Wiki source code of Connection to Senra
Show last authors
| author | version | line-number | content |
|---|---|---|---|
| 1 | **~ Contents:** | ||
| 2 | |||
| 3 | {{toc/}} | ||
| 4 | |||
| 5 | |||
| 6 | = 1. Introduction = | ||
| 7 | |||
| 8 | Here list some notice when connect to Senra. | ||
| 9 | |||
| 10 | = 2. Notice for Gateway = | ||
| 11 | |||
| 12 | ((( | ||
| 13 | After register an account in Senra, ask their support to approval your gateway: refer ths link [[https:~~/~~/docs.senraco.io/dev/gw/SemtechPacketForwarder/>>url:https://docs.senraco.io/dev/gw/SemtechPacketForwarder/]] for gateway instruction of Senra. | ||
| 14 | ))) | ||
| 15 | |||
| 16 | [[image:image-20220524181429-1.jpeg]] | ||
| 17 | |||
| 18 | |||
| 19 | Gateway Must be Approval | ||
| 20 | |||
| 21 | * The Gateway EUI must match the Approval Gateway EUI in above screen shot | ||
| 22 | * The keep alive status set to 300 seconds. Default 30 seconds is too short to Senra | ||
| 23 | |||
| 24 | [[image:image-20220524181455-2.png]] | ||
| 25 | |||
| 26 | Configure the Gateway with correct settings. | ||
| 27 | |||
| 28 | Gateway should be Active after have internet connection. like below: | ||
| 29 | |||
| 30 | [[image:image-20220524181508-3.png]] | ||
| 31 | |||
| 32 | Configure the Gateway with correct settings. | ||
| 33 | |||
| 34 | = 3. Notice for End node = | ||
| 35 | |||
| 36 | == 3.1 Set up for OTAA mode == | ||
| 37 | |||
| 38 | == 3.2 Set up for ABP Mode == | ||
| 39 | |||
| 40 | ((( | ||
| 41 | ((( | ||
| 42 | ABP Mode devices has to be IN868 frequency band as well, User can use ABP mode to update data. | ||
| 43 | ))) | ||
| 44 | ))) | ||
| 45 | |||
| 46 | ((( | ||
| 47 | ((( | ||
| 48 | For Dragino End Node, user can access to the device console and run AT Command "**AT+NJM=0**" to set it to ABP mode. | ||
| 49 | ))) | ||
| 50 | ))) | ||
| 51 | |||
| 52 | ((( | ||
| 53 | ((( | ||
| 54 | User can know the keys by run **AT+CFG**. | ||
| 55 | ))) | ||
| 56 | ))) | ||
| 57 | |||
| 58 | [[image:image-20220524181520-4.png]] | ||
| 59 | |||
| 60 | AT+CFG command output from End node | ||
| 61 | |||
| 62 | In Senra, need to create a ABP device | ||
| 63 | |||
| 64 | [[image:image-20220524181532-5.png]] | ||
| 65 | |||
| 66 | Create ABP Device | ||
| 67 | |||
| 68 | And input the keys: | ||
| 69 | |||
| 70 | * Device EUI : Use the value from AT+DEUI | ||
| 71 | * Device ADDR: Use the value from AT+DADDR | ||
| 72 | * Application session key: Use the value from AT+APPSKEY | ||
| 73 | * Network Session Key: Use the value from AT+NWKSKEY | ||
| 74 | |||
| 75 | [[image:image-20220524181549-6.png]] | ||
| 76 | |||
| 77 | Create ABP Device | ||
| 78 | |||
| 79 | After Successfule uplink, User will be to see the activity: | ||
| 80 | |||
| 81 | [[image:image-20220524181604-7.png]] | ||
| 82 | |||
| 83 | ABP Device Info |